3D-Drucker%2FSlicerBundle.ini.mw

   1 # generated by Slic3r 1.34.1-prusa3d-win64 on Tue Dec 19 18:45:57 2017
   2
   3 [filament:PETG 175]
   4 bed_temperature = 0
   5 bridge_fan_speed = 100
   6 cooling = 0
   7 disable_fan_first_layers = 5
   8 extrusion_multiplier = 1
   9 fan_always_on = 1
  10 fan_below_layer_time = 60
  11 filament_colour = #FFFFFF
  12 filament_cost = 27.4375
  13 filament_density = 1.27
  14 filament_diameter = 1.75
  15 filament_max_volumetric_speed = 0
  16 filament_notes = ""
  17 filament_settings_id =
  18 first_layer_bed_temperature = 0
  19 first_layer_temperature = 245
  20 max_fan_speed = 100
  21 min_fan_speed = 100
  22 min_print_speed = 5
  23 slowdown_below_layer_time = 20
  24 temperature = 220
  25
  26 [filament:PETG 285]
  27 bed_temperature = 75
  28 bridge_fan_speed = 100
  29 cooling = 1
  30 disable_fan_first_layers = 3
  31 extrusion_multiplier = 1
  32 fan_always_on = 1
  33 fan_below_layer_time = 60
  34 filament_colour = #FFFFFF
  35 filament_cost = 27.4375
  36 filament_density = 1.27
  37 filament_diameter = 2.85
  38 filament_max_volumetric_speed = 0
  39 filament_notes = ""
  40 filament_settings_id =
  41 first_layer_bed_temperature = 75
  42 first_layer_temperature = 250
  43 max_fan_speed = 100
  44 min_fan_speed = 100
  45 min_print_speed = 5
  46 slowdown_below_layer_time = 20
  47 temperature = 240
  48
  49 [filament:PLA 175]
  50 bed_temperature = 0
  51 bridge_fan_speed = 100
  52 cooling = 1
  53 disable_fan_first_layers = 3
  54 extrusion_multiplier = 1
  55 fan_always_on = 1
  56 fan_below_layer_time = 60
  57 filament_colour = #FFFFFF
  58 filament_cost = 0
  59 filament_density = 0
  60 filament_diameter = 1.75
  61 filament_max_volumetric_speed = 0
  62 filament_notes = ""
  63 filament_settings_id =
  64 first_layer_bed_temperature = 0
  65 first_layer_temperature = 230
  66 max_fan_speed = 100
  67 min_fan_speed = 80
  68 min_print_speed = 10
  69 slowdown_below_layer_time = 20
  70 temperature = 190
  71
  72 [filament:PLA 285]
  73 bed_temperature = 60
  74 bridge_fan_speed = 100
  75 cooling = 1
  76 disable_fan_first_layers = 10
  77 extrusion_multiplier = 1
  78 fan_always_on = 1
  79 fan_below_layer_time = 60
  80 filament_colour = #FFFFFF
  81 filament_cost = 0
  82 filament_density = 0
  83 filament_diameter = 2.85
  84 filament_max_volumetric_speed = 0
  85 filament_notes = ""
  86 filament_settings_id =
  87 first_layer_bed_temperature = 75
  88 first_layer_temperature = 230
  89 max_fan_speed = 100
  90 min_fan_speed = 100
  91 min_print_speed = 5
  92 slowdown_below_layer_time = 20
  93 temperature = 220
  94
  95 [presets]
  96 filament = PETG 175.ini
  97 print = Kossel.ini
  98 printer = Kossel.ini
  99
 100 [print:Kossel]
 101 avoid_crossing_perimeters = 0
 102 bottom_solid_layers = 2
 103 bridge_acceleration = 0
 104 bridge_flow_ratio = 1
 105 bridge_speed = 40
 106 brim_width = 2
 107 clip_multipart_objects = 0
 108 complete_objects = 0
 109 default_acceleration = 0
 110 dont_support_bridges = 1
 111 ensure_vertical_shell_thickness = 1
 112 external_fill_pattern = rectilinear
 113 external_perimeter_extrusion_width = 0
 114 external_perimeter_speed = 30
 115 external_perimeters_first = 0
 116 extra_perimeters = 1
 117 extruder_clearance_height = 20
 118 extruder_clearance_radius = 20
 119 extrusion_width = 0
 120 fill_angle = 45
 121 fill_density = 20%
 122 fill_pattern = honeycomb
 123 first_layer_acceleration = 0
 124 first_layer_extrusion_width = 200%
 125 first_layer_height = 0.2
 126 first_layer_speed = 10
 127 gap_fill_speed = 20
 128 gcode_comments = 0
 129 infill_acceleration = 0
 130 infill_every_layers = 1
 131 infill_extruder = 1
 132 infill_extrusion_width = 0
 133 infill_first = 0
 134 infill_only_where_needed = 0
 135 infill_overlap = 15%
 136 infill_speed = 60
 137 interface_shells = 0
 138 layer_height = 0.2
 139 max_print_speed = 80
 140 max_volumetric_extrusion_rate_slope_negative = 0
 141 max_volumetric_extrusion_rate_slope_positive = 0
 142 max_volumetric_speed = 0
 143 min_skirt_length = 0
 144 notes =
 145 only_retract_when_crossing_perimeters = 1
 146 ooze_prevention = 0
 147 output_filename_format = [input_filename_base].gcode
 148 overhangs = 1
 149 perimeter_acceleration = 0
 150 perimeter_extruder = 1
 151 perimeter_extrusion_width = 0
 152 perimeter_speed = 60
 153 perimeters = 3
 154 post_process =
 155 print_settings_id =
 156 raft_layers = 0
 157 resolution = 0
 158 seam_position = aligned
 159 skirt_distance = 10
 160 skirt_height = 1
 161 skirts = 5
 162 small_perimeter_speed = 15
 163 solid_infill_below_area = 70
 164 solid_infill_every_layers = 0
 165 solid_infill_extruder = 1
 166 solid_infill_extrusion_width = 0
 167 solid_infill_speed = 20
 168 spiral_vase = 0
 169 standby_temperature_delta = -5
 170 support_material = 0
 171 support_material_angle = 0
 172 support_material_buildplate_only = 0
 173 support_material_contact_distance = 0.4
 174 support_material_enforce_layers = 0
 175 support_material_extruder = 1
 176 support_material_extrusion_width = 0
 177 support_material_interface_contact_loops = 0
 178 support_material_interface_extruder = 1
 179 support_material_interface_layers = 3
 180 support_material_interface_spacing = 0
 181 support_material_interface_speed = 100%
 182 support_material_pattern = pillars
 183 support_material_spacing = 2.5
 184 support_material_speed = 60
 185 support_material_synchronize_layers = 0
 186 support_material_threshold = 0
 187 support_material_with_sheath = 1
 188 support_material_xy_spacing = 50%
 189 thin_walls = 1
 190 threads = 2
 191 top_infill_extrusion_width = 0
 192 top_solid_infill_speed = 15
 193 top_solid_layers = 3
 194 travel_speed = 130
 195 xy_size_compensation = 0
 196
 197 [print:Lulzbot]
 198 avoid_crossing_perimeters = 0
 199 bottom_solid_layers = 3
 200 bridge_acceleration = 2000
 201 bridge_flow_ratio = 1
 202 bridge_speed = 72
 203 brim_width = 0
 204 clip_multipart_objects = 0
 205 complete_objects = 0
 206 default_acceleration = 2000
 207 dont_support_bridges = 1
 208 ensure_vertical_shell_thickness = 1
 209 external_fill_pattern = rectilinear
 210 external_perimeter_extrusion_width = 0
 211 external_perimeter_speed = 45
 212 external_perimeters_first = 0
 213 extra_perimeters = 1
 214 extruder_clearance_height = 20
 215 extruder_clearance_radius = 20
 216 extrusion_width = 0.42
 217 fill_angle = 45
 218 fill_density = 5%
 219 fill_pattern = rectilinear
 220 first_layer_acceleration = 2000
 221 first_layer_extrusion_width = 0.53
 222 first_layer_height = 100%
 223 first_layer_speed = 75%
 224 gap_fill_speed = 55
 225 gcode_comments = 0
 226 infill_acceleration = 2000
 227 infill_every_layers = 1
 228 infill_extruder = 1
 229 infill_extrusion_width = 0.68
 230 infill_first = 0
 231 infill_only_where_needed = 0
 232 infill_overlap = 55%
 233 infill_speed = 80
 234 interface_shells = 0
 235 layer_height = 0.2
 236 max_print_speed = 80
 237 max_volumetric_extrusion_rate_slope_negative = 0
 238 max_volumetric_extrusion_rate_slope_positive = 0
 239 max_volumetric_speed = 0
 240 min_skirt_length = 0
 241 notes =
 242 only_retract_when_crossing_perimeters = 0
 243 ooze_prevention = 0
 244 output_filename_format = [input_filename_base].gcode
 245 overhangs = 1
 246 perimeter_acceleration = 1200
 247 perimeter_extruder = 1
 248 perimeter_extrusion_width = 0.38
 249 perimeter_speed = 75
 250 perimeters = 2
 251 post_process =
 252 print_settings_id =
 253 raft_layers = 0
 254 resolution = 0
 255 seam_position = aligned
 256 skirt_distance = 5
 257 skirt_height = 1
 258 skirts = 0
 259 small_perimeter_speed = 50
 260 solid_infill_below_area = 90
 261 solid_infill_every_layers = 0
 262 solid_infill_extruder = 1
 263 solid_infill_extrusion_width = 0.5
 264 solid_infill_speed = 75
 265 spiral_vase = 0
 266 standby_temperature_delta = -5
 267 support_material = 0
 268 support_material_angle = 0
 269 support_material_buildplate_only = 0
 270 support_material_contact_distance = 0.3
 271 support_material_enforce_layers = 0
 272 support_material_extruder = 1
 273 support_material_extrusion_width = 0
 274 support_material_interface_contact_loops = 0
 275 support_material_interface_extruder = 1
 276 support_material_interface_layers = 5
 277 support_material_interface_spacing = 0
 278 support_material_interface_speed = 100%
 279 support_material_pattern = rectilinear-grid
 280 support_material_spacing = 7
 281 support_material_speed = 60
 282 support_material_synchronize_layers = 0
 283 support_material_threshold = 30
 284 support_material_with_sheath = 0
 285 support_material_xy_spacing = 0.5
 286 thin_walls = 1
 287 threads = 2
 288 top_infill_extrusion_width = 0.4
 289 top_solid_infill_speed = 60
 290 top_solid_layers = 5
 291 travel_speed = 160
 292 xy_size_compensation = 0
 293
 294 [print:Mendel]
 295 avoid_crossing_perimeters = 0
 296 bottom_solid_layers = 3
 297 bridge_acceleration = 0
 298 bridge_flow_ratio = 1
 299 bridge_speed = 40
 300 brim_width = 2
 301 clip_multipart_objects = 0
 302 complete_objects = 0
 303 default_acceleration = 0
 304 dont_support_bridges = 1
 305 ensure_vertical_shell_thickness = 1
 306 external_fill_pattern = rectilinear
 307 external_perimeter_extrusion_width = 0
 308 external_perimeter_speed = 30
 309 external_perimeters_first = 0
 310 extra_perimeters = 1
 311 extruder_clearance_height = 20
 312 extruder_clearance_radius = 20
 313 extrusion_width = 0
 314 fill_angle = 45
 315 fill_density = 20%
 316 fill_pattern = cubic
 317 first_layer_acceleration = 0
 318 first_layer_extrusion_width = 150%
 319 first_layer_height = 0.2
 320 first_layer_speed = 20
 321 gap_fill_speed = 20
 322 gcode_comments = 0
 323 infill_acceleration = 0
 324 infill_every_layers = 1
 325 infill_extruder = 1
 326 infill_extrusion_width = 0
 327 infill_first = 0
 328 infill_only_where_needed = 0
 329 infill_overlap = 15%
 330 infill_speed = 40
 331 interface_shells = 0
 332 layer_height = 0.2
 333 max_print_speed = 40
 334 max_volumetric_extrusion_rate_slope_negative = 0
 335 max_volumetric_extrusion_rate_slope_positive = 0
 336 max_volumetric_speed = 0
 337 min_skirt_length = 0
 338 notes =
 339 only_retract_when_crossing_perimeters = 1
 340 ooze_prevention = 0
 341 output_filename_format = [input_filename_base].gcode
 342 overhangs = 1
 343 perimeter_acceleration = 0
 344 perimeter_extruder = 1
 345 perimeter_extrusion_width = 0
 346 perimeter_speed = 40
 347 perimeters = 3
 348 post_process =
 349 print_settings_id =
 350 raft_layers = 0
 351 resolution = 0
 352 seam_position = aligned
 353 skirt_distance = 6
 354 skirt_height = 1
 355 skirts = 3
 356 small_perimeter_speed = 15
 357 solid_infill_below_area = 70
 358 solid_infill_every_layers = 0
 359 solid_infill_extruder = 1
 360 solid_infill_extrusion_width = 0
 361 solid_infill_speed = 20
 362 spiral_vase = 0
 363 standby_temperature_delta = -5
 364 support_material = 1
 365 support_material_angle = 0
 366 support_material_buildplate_only = 0
 367 support_material_contact_distance = 0.2
 368 support_material_enforce_layers = 0
 369 support_material_extruder = 1
 370 support_material_extrusion_width = 0
 371 support_material_interface_contact_loops = 0
 372 support_material_interface_extruder = 1
 373 support_material_interface_layers = 3
 374 support_material_interface_spacing = 0
 375 support_material_interface_speed = 30
 376 support_material_pattern = pillars
 377 support_material_spacing = 2.5
 378 support_material_speed = 40
 379 support_material_synchronize_layers = 0
 380 support_material_threshold = 0
 381 support_material_with_sheath = 1
 382 support_material_xy_spacing = 50%
 383 thin_walls = 1
 384 threads = 2
 385 top_infill_extrusion_width = 0
 386 top_solid_infill_speed = 15
 387 top_solid_layers = 4
 388 travel_speed = 60
 389 xy_size_compensation = 0
 390
 391 [print:desktop]
 392
 393 [printer:Kossel]
 394 bed_shape = 79.5618x8.36228,78.2518x16.6329,76.0845x24.7214,73.0836x32.5389,69.282x40,64.7214x47.0228,59.4516x53.5304,53.5304x59.4516,47.0228x64.7214,40x69.282,32.5389x73.0836,24.7214x76.0845,16.6329x78.2518,8.36228x79.5618,0x80,-8.36228x79.5618,-16.6329x78.2518,-24.7214x76.0845,-32.5389x73.0836,-40x69.282,-47.0228x64.7214,-53.5304x59.4516,-59.4516x53.5304,-64.7214x47.0228,-69.282x40,-73.0836x32.5389,-76.0845x24.7214,-78.2518x16.6329,-79.5618x8.36228,-80x0,-79.5618x-8.36228,-78.2518x-16.6329,-76.0845x-24.7214,-73.0836x-32.5389,-69.282x-40,-64.7214x-47.0228,-59.4516x-53.5304,-53.5304x-59.4516,-47.0228x-64.7214,-40x-69.282,-32.5389x-73.0836,-24.7214x-76.0845,-16.6329x-78.2518,-8.36228x-79.5618,0x-80,8.36228x-79.5618,16.6329x-78.2518,24.7214x-76.0845,32.5389x-73.0836,40x-69.282,47.0228x-64.7214,53.5304x-59.4516,59.4516x-53.5304,64.7214x-47.0228,69.282x-40,73.0836x-32.5389,76.0845x-24.7214,78.2518x-16.6329,79.5618x-8.36228,80x0
 395 before_layer_gcode =
 396 end_gcode = M104 S0 ; turn off nozzle temperature\nG28; Home\nM84 ; disable motors
 397 extruder_offset = 0x0,0x0,0x0
 398 gcode_flavor = reprap
 399 layer_gcode =
 400 max_layer_height = 0.3,0.3,0.3
 401 min_layer_height = 0.07,0.07,0.07
 402 nozzle_diameter = 0.4,0.4,0.4
 403 octoprint_apikey =
 404 octoprint_host =
 405 printer_settings_id =
 406 retract_before_travel = 2,2,2
 407 retract_layer_change = 1,1,1
 408 retract_length = 2,2,2
 409 retract_length_toolchange = 3,3,3
 410 retract_lift = 0,0,0
 411 retract_lift_above = 0,0,0
 412 retract_lift_below = 0,0,0
 413 retract_restart_extra = 0.01,0.01,0.01
 414 retract_restart_extra_toolchange = 0,0,0
 415 retract_speed = 20,20,20
 416 serial_port =
 417 serial_speed = 250000
 418 start_gcode = ; Cyan\nM163 S0 P1\nM163 S1 P0\nM163 S2 P0\nM164 S0\n\n; Ocean\nM163 S0 P5\nM163 S1 P1\nM163 S2 P0\nM164 S1\n\n; Blue\nM163 S0 P1\nM163 S1 P1\nM163 S2 P0\nM164 S2\n\n; Violet\nM163 S0 P1\nM163 S1 P5\nM163 S2 P0\nM164 S3\n\n; Magenta\nM163 S0 P0\nM163 S1 P1\nM163 S2 P0\nM164 S4\n\n; Raspberry\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S5\n\n; Red\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S6\n\n; Orange\nM163 S0 P0\nM163 S1 P1\nM163 S2 P1\nM164 S7\n\n; Yellow\nM163 S0 P0\nM163 S1 P0\nM163 S2 P1\nM164 S8\n\n; Spring Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P5\nM164 S9\n\n; Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P1\nM164 S10\n\n; Turquoise\nM163 S0 P5\nM163 S1 P0\nM163 S2 P1\nM164 S11\n\n\n; Cyan-Brown\nM163 S0 P2\nM163 S1 P1\nM163 S2 P1\nM164 S12\n\n; Magenta-Brown\nM163 S0 P1\nM163 S1 P2\nM163 S2 P1\nM164 S13\n\n; Yellow-Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P2\nM164 S14\n\n; Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P1\nM164 S15\n
 419 toolchange_gcode =
 420 use_firmware_retraction = 1
 421 use_relative_e_distances = 0
 422 use_volumetric_e = 0
 423 variable_layer_height = 0
 424 wipe = 0,0,0
 425 z_offset = 0
 426
 427 [printer:Lulzbot]
 428 bed_shape = 0x0,298x0,298x275,0x275
 429 before_layer_gcode =
 430 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
 431 extruder_offset = 0x0
 432 gcode_flavor = reprap
 433 layer_gcode =
 434 max_layer_height = 0.3
 435 min_layer_height = 0.07
 436 nozzle_diameter = 0.35
 437 octoprint_apikey =
 438 octoprint_host =
 439 pressure_advance = 0
 440 printer_settings_id =
 441 retract_before_travel = 2
 442 retract_layer_change = 1
 443 retract_length = 5
 444 retract_length_toolchange = 3
 445 retract_lift = 0
 446 retract_lift_above = 1
 447 retract_lift_below = 0
 448 retract_restart_extra = 0.05
 449 retract_restart_extra_toolchange = 0
 450 retract_speed = 60
 451 serial_port =
 452 serial_speed = 250000
 453 start_gcode = G28 ; home all axes\n
 454 toolchange_gcode =
 455 use_firmware_retraction = 0
 456 use_relative_e_distances = 0
 457 use_volumetric_e = 0
 458 variable_layer_height = 1
 459 wipe = 0
 460 z_offset = 0
 461
 462 [printer:Mendel]
 463 bed_shape = 0x0,218x0,218x201,0x201
 464 before_layer_gcode =
 465 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
 466 extruder_offset = 0x0
 467 gcode_flavor = reprap
 468 layer_gcode =
 469 max_layer_height = 0.3
 470 min_layer_height = 0.07
 471 nozzle_diameter = 0.5
 472 octoprint_apikey =
 473 octoprint_host =
 474 pressure_advance = 0
 475 printer_settings_id =
 476 retract_before_travel = 2
 477 retract_layer_change = 1
 478 retract_length = 2
 479 retract_length_toolchange = 3
 480 retract_lift = 0
 481 retract_lift_above = 0
 482 retract_lift_below = 0
 483 retract_restart_extra = 0.01
 484 retract_restart_extra_toolchange = 0
 485 retract_speed = 20
 486 serial_port =
 487 serial_speed = 250000
 488 start_gcode = G28 ; home all axes\n
 489 toolchange_gcode =
 490 use_firmware_retraction = 0
 491 use_relative_e_distances = 0
 492 use_volumetric_e = 0
 493 variable_layer_height = 1
 494 wipe = 0
 495 z_offset = 0
 496
 497 [printer:Tiny]
 498 bed_shape = 0x0,80x0,80x74,0x74
 499 before_layer_gcode =
 500 end_gcode = M104 S0 ; turn off nozzle temperature\nG28 X0 ; home X axis
 501 extruder_offset = 0x0
 502 gcode_flavor = reprap
 503 layer_gcode =
 504 max_layer_height = 0.3
 505 min_layer_height = 0.07
 506 nozzle_diameter = 0.4
 507 octoprint_apikey =
 508 octoprint_host =
 509 pressure_advance = 0
 510 printer_settings_id =
 511 retract_before_travel = 2
 512 retract_layer_change = 1
 513 retract_length = 2
 514 retract_length_toolchange = 3
 515 retract_lift = 0
 516 retract_lift_above = 1
 517 retract_lift_below = 0
 518 retract_restart_extra = 0.01
 519 retract_restart_extra_toolchange = 0
 520 retract_speed = 40
 521 serial_port =
 522 serial_speed = 250000
 523 start_gcode = G28 ; home all axes\n
 524 toolchange_gcode =
 525 use_firmware_retraction = 0
 526 use_relative_e_distances = 0
 527 use_volumetric_e = 0
 528 variable_layer_height = 1
 529 wipe = 0
 530 z_offset = 0
 531
 532 [settings]
 533 autocenter = 1
 534 mode = expert