3D-Drucker%2FSlicerBundle.ini.mw

   1 # generated by Slic3r Prusa Edition 1.38.5-prusa3d-win64 on 2018-01-16 at 20:47:39
   2
   3 [print:Kossel print]
   4 avoid_crossing_perimeters = 1
   5 bottom_solid_layers = 3
   6 bridge_acceleration = 0
   7 bridge_angle = 0
   8 bridge_flow_ratio = 1
   9 bridge_speed = 60
  10 brim_width = 0
  11 clip_multipart_objects = 0
  12 compatible_printers =
  13 compatible_printers_condition =
  14 complete_objects = 0
  15 default_acceleration = 0
  16 dont_support_bridges = 1
  17 elefant_foot_compensation = 0
  18 ensure_vertical_shell_thickness = 1
  19 external_fill_pattern = rectilinear
  20 external_perimeter_extrusion_width = 0
  21 external_perimeter_speed = 30
  22 external_perimeters_first = 0
  23 extra_perimeters = 1
  24 extruder_clearance_height = 20
  25 extruder_clearance_radius = 20
  26 extrusion_width = 0
  27 fill_angle = 45
  28 fill_density = 20%
  29 fill_pattern = cubic
  30 first_layer_acceleration = 0
  31 first_layer_extrusion_width = 200%
  32 first_layer_height = 0.2
  33 first_layer_speed = 30
  34 gap_fill_speed = 20
  35 gcode_comments = 0
  36 infill_acceleration = 0
  37 infill_every_layers = 1
  38 infill_extruder = 1
  39 infill_extrusion_width = 0
  40 infill_first = 0
  41 infill_only_where_needed = 0
  42 infill_overlap = 25%
  43 infill_speed = 80
  44 interface_shells = 0
  45 layer_height = 0.2
  46 max_print_speed = 80
  47 max_volumetric_extrusion_rate_slope_negative = 0
  48 max_volumetric_extrusion_rate_slope_positive = 0
  49 max_volumetric_speed = 0
  50 min_skirt_length = 0
  51 notes =
  52 only_retract_when_crossing_perimeters = 1
  53 ooze_prevention = 0
  54 output_filename_format = [input_filename_base].gcode
  55 overhangs = 1
  56 perimeter_acceleration = 0
  57 perimeter_extruder = 1
  58 perimeter_extrusion_width = 0
  59 perimeter_speed = 60
  60 perimeters = 3
  61 post_process =
  62 raft_layers = 0
  63 resolution = 0
  64 seam_position = aligned
  65 skirt_distance = 6
  66 skirt_height = 1
  67 skirts = 3
  68 small_perimeter_speed = 15
  69 solid_infill_below_area = 70
  70 solid_infill_every_layers = 0
  71 solid_infill_extruder = 1
  72 solid_infill_extrusion_width = 0
  73 solid_infill_speed = 20
  74 spiral_vase = 0
  75 standby_temperature_delta = -5
  76 support_material = 0
  77 support_material_angle = 0
  78 support_material_buildplate_only = 0
  79 support_material_contact_distance = 0.4
  80 support_material_enforce_layers = 0
  81 support_material_extruder = 1
  82 support_material_extrusion_width = 0
  83 support_material_interface_contact_loops = 0
  84 support_material_interface_extruder = 1
  85 support_material_interface_layers = 3
  86 support_material_interface_spacing = 0
  87 support_material_interface_speed = 100%
  88 support_material_pattern = pillars
  89 support_material_spacing = 2.5
  90 support_material_speed = 60
  91 support_material_synchronize_layers = 0
  92 support_material_threshold = 40
  93 support_material_with_sheath = 1
  94 support_material_xy_spacing = 0.6
  95 thin_walls = 1
  96 threads = 2
  97 top_infill_extrusion_width = 0
  98 top_solid_infill_speed = 15
  99 top_solid_layers = 3
 100 travel_speed = 130
 101 wipe_tower = 1
 102 wipe_tower_per_color_wipe = 10
 103 wipe_tower_width = 10
 104 wipe_tower_x = 0
 105 wipe_tower_y = 65
 106 xy_size_compensation = 0
 107
 108 [print:Lulzbot print]
 109 avoid_crossing_perimeters = 1
 110 bottom_solid_layers = 3
 111 bridge_acceleration = 2000
 112 bridge_angle = 0
 113 bridge_flow_ratio = 1
 114 bridge_speed = 72
 115 brim_width = 0
 116 clip_multipart_objects = 0
 117 compatible_printers =
 118 compatible_printers_condition =
 119 complete_objects = 0
 120 default_acceleration = 2000
 121 dont_support_bridges = 1
 122 elefant_foot_compensation = 0
 123 ensure_vertical_shell_thickness = 1
 124 external_fill_pattern = rectilinear
 125 external_perimeter_extrusion_width = 0
 126 external_perimeter_speed = 45
 127 external_perimeters_first = 0
 128 extra_perimeters = 1
 129 extruder_clearance_height = 20
 130 extruder_clearance_radius = 20
 131 extrusion_width = 0.42
 132 fill_angle = 45
 133 fill_density = 20%
 134 fill_pattern = cubic
 135 first_layer_acceleration = 2000
 136 first_layer_extrusion_width = 0.53
 137 first_layer_height = 100%
 138 first_layer_speed = 10
 139 gap_fill_speed = 55
 140 gcode_comments = 0
 141 infill_acceleration = 2000
 142 infill_every_layers = 1
 143 infill_extruder = 1
 144 infill_extrusion_width = 0.68
 145 infill_first = 0
 146 infill_only_where_needed = 0
 147 infill_overlap = 55%
 148 infill_speed = 80
 149 interface_shells = 0
 150 layer_height = 0.2
 151 max_print_speed = 80
 152 max_volumetric_extrusion_rate_slope_negative = 0
 153 max_volumetric_extrusion_rate_slope_positive = 0
 154 max_volumetric_speed = 0
 155 min_skirt_length = 0
 156 notes =
 157 only_retract_when_crossing_perimeters = 0
 158 ooze_prevention = 0
 159 output_filename_format = [input_filename_base].gcode
 160 overhangs = 1
 161 perimeter_acceleration = 1200
 162 perimeter_extruder = 1
 163 perimeter_extrusion_width = 0.38
 164 perimeter_speed = 75
 165 perimeters = 3
 166 post_process =
 167 print_settings_id =
 168 raft_layers = 0
 169 resolution = 0
 170 seam_position = aligned
 171 skirt_distance = 5
 172 skirt_height = 1
 173 skirts = 3
 174 small_perimeter_speed = 50
 175 solid_infill_below_area = 90
 176 solid_infill_every_layers = 0
 177 solid_infill_extruder = 1
 178 solid_infill_extrusion_width = 0.5
 179 solid_infill_speed = 75
 180 spiral_vase = 0
 181 standby_temperature_delta = -5
 182 support_material = 0
 183 support_material_angle = 0
 184 support_material_buildplate_only = 0
 185 support_material_contact_distance = 0.3
 186 support_material_enforce_layers = 0
 187 support_material_extruder = 1
 188 support_material_extrusion_width = 0
 189 support_material_interface_contact_loops = 0
 190 support_material_interface_extruder = 1
 191 support_material_interface_layers = 5
 192 support_material_interface_spacing = 0
 193 support_material_interface_speed = 100%
 194 support_material_pattern = rectilinear-grid
 195 support_material_spacing = 7
 196 support_material_speed = 60
 197 support_material_synchronize_layers = 0
 198 support_material_threshold = 30
 199 support_material_with_sheath = 0
 200 support_material_xy_spacing = 0.5
 201 thin_walls = 1
 202 threads = 2
 203 top_infill_extrusion_width = 0.4
 204 top_solid_infill_speed = 60
 205 top_solid_layers = 3
 206 travel_speed = 160
 207 wipe_tower = 0
 208 wipe_tower_per_color_wipe = 15
 209 wipe_tower_width = 60
 210 wipe_tower_x = 180
 211 wipe_tower_y = 140
 212 xy_size_compensation = 0
 213
 214 [print:Mendel print]
 215 avoid_crossing_perimeters = 0
 216 bottom_solid_layers = 3
 217 bridge_acceleration = 0
 218 bridge_angle = 0
 219 bridge_flow_ratio = 1
 220 bridge_speed = 40
 221 brim_width = 2
 222 clip_multipart_objects = 0
 223 compatible_printers =
 224 compatible_printers_condition =
 225 complete_objects = 0
 226 default_acceleration = 0
 227 dont_support_bridges = 1
 228 elefant_foot_compensation = 0
 229 ensure_vertical_shell_thickness = 1
 230 external_fill_pattern = rectilinear
 231 external_perimeter_extrusion_width = 0
 232 external_perimeter_speed = 30
 233 external_perimeters_first = 0
 234 extra_perimeters = 1
 235 extruder_clearance_height = 20
 236 extruder_clearance_radius = 20
 237 extrusion_width = 0
 238 fill_angle = 45
 239 fill_density = 20%
 240 fill_pattern = cubic
 241 first_layer_acceleration = 0
 242 first_layer_extrusion_width = 150%
 243 first_layer_height = 0.2
 244 first_layer_speed = 20
 245 gap_fill_speed = 20
 246 gcode_comments = 0
 247 infill_acceleration = 0
 248 infill_every_layers = 1
 249 infill_extruder = 1
 250 infill_extrusion_width = 0
 251 infill_first = 0
 252 infill_only_where_needed = 0
 253 infill_overlap = 15%
 254 infill_speed = 40
 255 interface_shells = 0
 256 layer_height = 0.2
 257 max_print_speed = 40
 258 max_volumetric_extrusion_rate_slope_negative = 0
 259 max_volumetric_extrusion_rate_slope_positive = 0
 260 max_volumetric_speed = 0
 261 min_skirt_length = 0
 262 notes =
 263 only_retract_when_crossing_perimeters = 1
 264 ooze_prevention = 0
 265 output_filename_format = [input_filename_base].gcode
 266 overhangs = 1
 267 perimeter_acceleration = 0
 268 perimeter_extruder = 1
 269 perimeter_extrusion_width = 0
 270 perimeter_speed = 40
 271 perimeters = 3
 272 post_process =
 273 print_settings_id =
 274 raft_layers = 0
 275 resolution = 0
 276 seam_position = aligned
 277 skirt_distance = 6
 278 skirt_height = 1
 279 skirts = 3
 280 small_perimeter_speed = 15
 281 solid_infill_below_area = 70
 282 solid_infill_every_layers = 0
 283 solid_infill_extruder = 1
 284 solid_infill_extrusion_width = 0
 285 solid_infill_speed = 20
 286 spiral_vase = 0
 287 standby_temperature_delta = -5
 288 support_material = 1
 289 support_material_angle = 0
 290 support_material_buildplate_only = 0
 291 support_material_contact_distance = 0.2
 292 support_material_enforce_layers = 0
 293 support_material_extruder = 1
 294 support_material_extrusion_width = 0
 295 support_material_interface_contact_loops = 0
 296 support_material_interface_extruder = 1
 297 support_material_interface_layers = 3
 298 support_material_interface_spacing = 0
 299 support_material_interface_speed = 30
 300 support_material_pattern = pillars
 301 support_material_spacing = 2.5
 302 support_material_speed = 40
 303 support_material_synchronize_layers = 0
 304 support_material_threshold = 0
 305 support_material_with_sheath = 1
 306 support_material_xy_spacing = 50%
 307 thin_walls = 1
 308 threads = 2
 309 top_infill_extrusion_width = 0
 310 top_solid_infill_speed = 15
 311 top_solid_layers = 4
 312 travel_speed = 60
 313 wipe_tower = 0
 314 wipe_tower_per_color_wipe = 15
 315 wipe_tower_width = 60
 316 wipe_tower_x = 180
 317 wipe_tower_y = 140
 318 xy_size_compensation = 0
 319
 320 [print:Tiny print]
 321 avoid_crossing_perimeters = 1
 322 bottom_solid_layers = 2
 323 bridge_acceleration = 0
 324 bridge_angle = 0
 325 bridge_flow_ratio = 1
 326 bridge_speed = 60
 327 brim_width = 2
 328 clip_multipart_objects = 0
 329 compatible_printers =
 330 compatible_printers_condition =
 331 complete_objects = 0
 332 default_acceleration = 0
 333 dont_support_bridges = 1
 334 elefant_foot_compensation = 0
 335 ensure_vertical_shell_thickness = 1
 336 external_fill_pattern = rectilinear
 337 external_perimeter_extrusion_width = 0
 338 external_perimeter_speed = 30
 339 external_perimeters_first = 0
 340 extra_perimeters = 1
 341 extruder_clearance_height = 20
 342 extruder_clearance_radius = 20
 343 extrusion_width = 0
 344 fill_angle = 45
 345 fill_density = 10%
 346 fill_pattern = rectilinear
 347 first_layer_acceleration = 0
 348 first_layer_extrusion_width = 120%
 349 first_layer_height = 0.2
 350 first_layer_speed = 20
 351 gap_fill_speed = 20
 352 gcode_comments = 0
 353 infill_acceleration = 0
 354 infill_every_layers = 1
 355 infill_extruder = 1
 356 infill_extrusion_width = 0
 357 infill_first = 0
 358 infill_only_where_needed = 0
 359 infill_overlap = 15%
 360 infill_speed = 80
 361 interface_shells = 0
 362 layer_height = 0.2
 363 max_print_speed = 100
 364 max_volumetric_extrusion_rate_slope_negative = 0
 365 max_volumetric_extrusion_rate_slope_positive = 0
 366 max_volumetric_speed = 0
 367 min_skirt_length = 0
 368 notes =
 369 only_retract_when_crossing_perimeters = 1
 370 ooze_prevention = 0
 371 output_filename_format = [input_filename_base].gcode
 372 overhangs = 1
 373 perimeter_acceleration = 0
 374 perimeter_extruder = 1
 375 perimeter_extrusion_width = 0
 376 perimeter_speed = 60
 377 perimeters = 2
 378 post_process =
 379 print_settings_id =
 380 raft_layers = 0
 381 resolution = 0
 382 seam_position = nearest
 383 skirt_distance = 6
 384 skirt_height = 1
 385 skirts = 3
 386 small_perimeter_speed = 15
 387 solid_infill_below_area = 70
 388 solid_infill_every_layers = 0
 389 solid_infill_extruder = 1
 390 solid_infill_extrusion_width = 0
 391 solid_infill_speed = 20
 392 spiral_vase = 0
 393 standby_temperature_delta = -5
 394 support_material = 1
 395 support_material_angle = 0
 396 support_material_buildplate_only = 1
 397 support_material_contact_distance = 0.2
 398 support_material_enforce_layers = 0
 399 support_material_extruder = 1
 400 support_material_extrusion_width = 0
 401 support_material_interface_contact_loops = 0
 402 support_material_interface_extruder = 1
 403 support_material_interface_layers = 3
 404 support_material_interface_spacing = 0
 405 support_material_interface_speed = 30
 406 support_material_pattern = pillars
 407 support_material_spacing = 2.5
 408 support_material_speed = 60
 409 support_material_synchronize_layers = 1
 410 support_material_threshold = 40
 411 support_material_with_sheath = 1
 412 support_material_xy_spacing = 0.4
 413 thin_walls = 1
 414 threads = 2
 415 top_infill_extrusion_width = 0
 416 top_solid_infill_speed = 15
 417 top_solid_layers = 3
 418 travel_speed = 130
 419 wipe_tower = 0
 420 wipe_tower_per_color_wipe = 15
 421 wipe_tower_width = 60
 422 wipe_tower_x = 180
 423 wipe_tower_y = 140
 424 xy_size_compensation = 0
 425
 426 [filament:ABS 175]
 427 bed_temperature = 0
 428 bridge_fan_speed = 100
 429 compatible_printers =
 430 compatible_printers_condition =
 431 cooling = 0
 432 disable_fan_first_layers = 3
 433 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 434 extrusion_multiplier = 1
 435 fan_always_on = 0
 436 fan_below_layer_time = 60
 437 filament_colour = #FFFFFF
 438 filament_cost = 0
 439 filament_density = 0
 440 filament_diameter = 1.75
 441 filament_max_volumetric_speed = 0
 442 filament_notes = ""
 443 filament_settings_id =
 444 filament_soluble = 0
 445 filament_type = PLA
 446 first_layer_bed_temperature = 0
 447 first_layer_temperature = 245
 448 max_fan_speed = 100
 449 min_fan_speed = 100
 450 min_print_speed = 5
 451 slowdown_below_layer_time = 20
 452 start_filament_gcode = "; Filament gcode\n"
 453 temperature = 235
 454
 455 [filament:PETG 175]
 456 bed_temperature = 0
 457 bridge_fan_speed = 100
 458 compatible_printers =
 459 compatible_printers_condition =
 460 cooling = 0
 461 disable_fan_first_layers = 5
 462 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 463 extrusion_multiplier = 1
 464 fan_always_on = 1
 465 fan_below_layer_time = 60
 466 filament_colour = #FFFFFF
 467 filament_cost = 27.4375
 468 filament_density = 1.27
 469 filament_diameter = 1.75
 470 filament_max_volumetric_speed = 0
 471 filament_notes = ""
 472 filament_settings_id =
 473 filament_soluble = 0
 474 filament_type = PET
 475 first_layer_bed_temperature = 0
 476 first_layer_temperature = 245
 477 max_fan_speed = 100
 478 min_fan_speed = 100
 479 min_print_speed = 5
 480 slowdown_below_layer_time = 20
 481 start_filament_gcode = "; Filament gcode\n"
 482 temperature = 220
 483
 484 [filament:PETG 285]
 485 bed_temperature = 75
 486 bridge_fan_speed = 100
 487 compatible_printers =
 488 compatible_printers_condition =
 489 cooling = 1
 490 disable_fan_first_layers = 3
 491 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 492 extrusion_multiplier = 0.9
 493 fan_always_on = 1
 494 fan_below_layer_time = 60
 495 filament_colour = #FFFFFF
 496 filament_cost = 27.4375
 497 filament_density = 1.27
 498 filament_diameter = 2.85
 499 filament_max_volumetric_speed = 0
 500 filament_notes = ""
 501 filament_settings_id =
 502 filament_soluble = 0
 503 filament_type = PLA
 504 first_layer_bed_temperature = 75
 505 first_layer_temperature = 250
 506 max_fan_speed = 100
 507 min_fan_speed = 100
 508 min_print_speed = 5
 509 slowdown_below_layer_time = 20
 510 start_filament_gcode = "; Filament gcode\n"
 511 temperature = 220
 512
 513 [filament:PLA 175]
 514 bed_temperature = 0
 515 bridge_fan_speed = 100
 516 compatible_printers =
 517 compatible_printers_condition =
 518 cooling = 1
 519 disable_fan_first_layers = 3
 520 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 521 extrusion_multiplier = 1
 522 fan_always_on = 1
 523 fan_below_layer_time = 60
 524 filament_colour = #FFFFFF
 525 filament_cost = 0
 526 filament_density = 0
 527 filament_diameter = 1.75
 528 filament_max_volumetric_speed = 0
 529 filament_notes = ""
 530 filament_settings_id =
 531 filament_soluble = 0
 532 filament_type = PLA
 533 first_layer_bed_temperature = 0
 534 first_layer_temperature = 230
 535 max_fan_speed = 60
 536 min_fan_speed = 35
 537 min_print_speed = 5
 538 slowdown_below_layer_time = 10
 539 start_filament_gcode = "; Filament gcode\n"
 540 temperature = 200
 541
 542 [filament:PLA 285]
 543 bed_temperature = 60
 544 bridge_fan_speed = 100
 545 compatible_printers =
 546 compatible_printers_condition =
 547 cooling = 1
 548 disable_fan_first_layers = 10
 549 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 550 extrusion_multiplier = 1
 551 fan_always_on = 1
 552 fan_below_layer_time = 60
 553 filament_colour = #FFFFFF
 554 filament_cost = 0
 555 filament_density = 0
 556 filament_diameter = 2.85
 557 filament_max_volumetric_speed = 0
 558 filament_notes = ""
 559 filament_settings_id =
 560 filament_soluble = 0
 561 filament_type = PLA
 562 first_layer_bed_temperature = 75
 563 first_layer_temperature = 230
 564 max_fan_speed = 100
 565 min_fan_speed = 100
 566 min_print_speed = 5
 567 slowdown_below_layer_time = 20
 568 start_filament_gcode = "; Filament gcode\n"
 569 temperature = 220
 570
 571 [filament:WillowFlex 285]
 572 bed_temperature = 60
 573 bridge_fan_speed = 100
 574 compatible_printers =
 575 compatible_printers_condition =
 576 cooling = 1
 577 disable_fan_first_layers = 0
 578 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
 579 extrusion_multiplier = 0.9
 580 fan_always_on = 1
 581 fan_below_layer_time = 60
 582 filament_colour = #FFFFFF
 583 filament_cost = 27.4375
 584 filament_density = 1.27
 585 filament_diameter = 2.85
 586 filament_max_volumetric_speed = 0
 587 filament_notes = ""
 588 filament_settings_id =
 589 filament_soluble = 0
 590 filament_type = PLA
 591 first_layer_bed_temperature = 60
 592 first_layer_temperature = 175
 593 max_fan_speed = 100
 594 min_fan_speed = 100
 595 min_print_speed = 5
 596 slowdown_below_layer_time = 20
 597 start_filament_gcode = "; Filament gcode\n"
 598 temperature = 175
 599
 600 [printer:Kossel]
 601 bed_shape = 79.5618x8.36228,78.2518x16.6329,76.0845x24.7214,73.0836x32.5389,69.282x40,64.7214x47.0228,59.4516x53.5304,53.5304x59.4516,47.0228x64.7214,40x69.282,32.5389x73.0836,24.7214x76.0845,16.6329x78.2518,8.36228x79.5618,0x80,-8.36228x79.5618,-16.6329x78.2518,-24.7214x76.0845,-32.5389x73.0836,-40x69.282,-47.0228x64.7214,-53.5304x59.4516,-59.4516x53.5304,-64.7214x47.0228,-69.282x40,-73.0836x32.5389,-76.0845x24.7214,-78.2518x16.6329,-79.5618x8.36228,-80x0,-79.5618x-8.36228,-78.2518x-16.6329,-76.0845x-24.7214,-73.0836x-32.5389,-69.282x-40,-64.7214x-47.0228,-59.4516x-53.5304,-53.5304x-59.4516,-47.0228x-64.7214,-40x-69.282,-32.5389x-73.0836,-24.7214x-76.0845,-16.6329x-78.2518,-8.36228x-79.5618,0x-80,8.36228x-79.5618,16.6329x-78.2518,24.7214x-76.0845,32.5389x-73.0836,40x-69.282,47.0228x-64.7214,53.5304x-59.4516,59.4516x-53.5304,64.7214x-47.0228,69.282x-40,73.0836x-32.5389,76.0845x-24.7214,78.2518x-16.6329,79.5618x-8.36228,80x0
 602 before_layer_gcode =
 603 between_objects_gcode =
 604 deretract_speed = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 605 end_gcode = M104 S0 ; turn off nozzle temperature\nG28; Home\nM84 ; disable motors\nM82; absolute E
 606 extruder_colour = #FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000;#FF0000
 607 extruder_offset = 0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0,0x0
 608 gcode_flavor = reprap
 609 layer_gcode =
 610 max_layer_height = 0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3,0.3
 611 min_layer_height = 0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07,0.07
 612 nozzle_diameter = 0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4,0.4
 613 octoprint_apikey =
 614 octoprint_host =
 615 printer_notes =
 616 printer_settings_id =
 617 retract_before_travel = 2,2,2,2,2,2,2,2,2,2,2,2,2,2,2,2
 618 retract_before_wipe = 0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%,0%
 619 retract_layer_change = 1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1
 620 retract_length = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 621 retract_length_toolchange = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 622 retract_lift = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 623 retract_lift_above = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 624 retract_lift_below = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 625 retract_restart_extra = 0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01,0.01
 626 retract_restart_extra_toolchange = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 627 retract_speed = 20,20,20,20,20,20,20,20,20,20,20,20,20,20,20,20
 628 serial_port =
 629 serial_speed = 250000
 630 single_extruder_multi_material = 1
 631 start_gcode = ;M104 S230  ;Temperatur\n;G29 S2         ;Autobed Level\n;G132 S1       ;Store Offset\n\nM83 ;relativ E \n\n; Cyan\nM163 S0 P1\nM163 S1 P0\nM163 S2 P0\nM164 S0\n\n; Ocean\nM163 S0 P5\nM163 S1 P1\nM163 S2 P0\nM164 S1\n\n; Blue\nM163 S0 P1\nM163 S1 P1\nM163 S2 P0\nM164 S2\n\n; Violet\nM163 S0 P1\nM163 S1 P5\nM163 S2 P0\nM164 S3\n\n; Magenta\nM163 S0 P0\nM163 S1 P1\nM163 S2 P0\nM164 S4\n\n; Raspberry\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S5\n\n; Red\nM163 S0 P0\nM163 S1 P5\nM163 S2 P1\nM164 S6\n\n; Orange\nM163 S0 P0\nM163 S1 P1\nM163 S2 P1\nM164 S7\n\n; Yellow\nM163 S0 P0\nM163 S1 P0\nM163 S2 P1\nM164 S8\n\n; Spring Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P5\nM164 S9\n\n; Green\nM163 S0 P1\nM163 S1 P0\nM163 S2 P1\nM164 S10\n\n; Turquoise\nM163 S0 P5\nM163 S1 P0\nM163 S2 P1\nM164 S11\n\n\n; Cyan-Brown\nM163 S0 P2\nM163 S1 P1\nM163 S2 P1\nM164 S12\n\n; Magenta-Brown\nM163 S0 P1\nM163 S1 P2\nM163 S2 P1\nM164 S13\n\n; Yellow-Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P2\nM164 S14\n\n; Brown\nM163 S0 P1\nM163 S1 P1\nM163 S2 P1\nM164 S15\n
 632 toolchange_gcode =
 633 use_firmware_retraction = 0
 634 use_relative_e_distances = 1
 635 use_volumetric_e = 0
 636 variable_layer_height = 0
 637 wipe = 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
 638 z_offset = 0
 639
 640 [printer:Lulzbot]
 641 bed_shape = 0x0,300x0,300x300,0x300
 642 before_layer_gcode =
 643 between_objects_gcode =
 644 deretract_speed = 0
 645 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
 646 extruder_colour = ""
 647 extruder_offset = 0x0
 648 gcode_flavor = reprap
 649 layer_gcode =
 650 max_layer_height = 0.3
 651 min_layer_height = 0.07
 652 nozzle_diameter = 0.35
 653 octoprint_apikey =
 654 octoprint_host =
 655 printer_notes =
 656 printer_settings_id =
 657 retract_before_travel = 2
 658 retract_before_wipe = 0%
 659 retract_layer_change = 1
 660 retract_length = 5
 661 retract_length_toolchange = 3
 662 retract_lift = 0
 663 retract_lift_above = 1
 664 retract_lift_below = 0
 665 retract_restart_extra = 0
 666 retract_restart_extra_toolchange = 0
 667 retract_speed = 60
 668 serial_port =
 669 serial_speed = 250000
 670 single_extruder_multi_material = 0
 671 start_gcode = G28 ; home all axes\n
 672 toolchange_gcode =
 673 use_firmware_retraction = 0
 674 use_relative_e_distances = 0
 675 use_volumetric_e = 0
 676 variable_layer_height = 0
 677 wipe = 1
 678 z_offset = 0
 679
 680 [printer:Mendel]
 681 bed_shape = 0x0,218x0,218x201,0x201
 682 before_layer_gcode =
 683 between_objects_gcode =
 684 deretract_speed = 0
 685 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors\n\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\nM355 S1;\nG4 P500;\nM355 S0;\nG4 P500;\n
 686 extruder_colour = ""
 687 extruder_offset = 0x0
 688 gcode_flavor = reprap
 689 layer_gcode =
 690 max_layer_height = 0.3
 691 min_layer_height = 0.07
 692 nozzle_diameter = 0.5
 693 octoprint_apikey =
 694 octoprint_host =
 695 printer_notes =
 696 printer_settings_id =
 697 retract_before_travel = 2
 698 retract_before_wipe = 0%
 699 retract_layer_change = 1
 700 retract_length = 2
 701 retract_length_toolchange = 3
 702 retract_lift = 0
 703 retract_lift_above = 0
 704 retract_lift_below = 0
 705 retract_restart_extra = 0.01
 706 retract_restart_extra_toolchange = 0
 707 retract_speed = 20
 708 serial_port =
 709 serial_speed = 250000
 710 single_extruder_multi_material = 0
 711 start_gcode = G28 ; home all axes\n
 712 toolchange_gcode =
 713 use_firmware_retraction = 0
 714 use_relative_e_distances = 0
 715 use_volumetric_e = 0
 716 variable_layer_height = 1
 717 wipe = 0
 718 z_offset = 0
 719
 720 [printer:Tiny]
 721 bed_shape = 0x0,80x0,80x74,0x74
 722 before_layer_gcode =
 723 between_objects_gcode =
 724 deretract_speed = 0
 725 end_gcode = M104 S0 ; turn off nozzle temperature\nG28 X0 ; home X axis
 726 extruder_colour = ""
 727 extruder_offset = 0x0
 728 gcode_flavor = reprap
 729 layer_gcode =
 730 max_layer_height = 0.3
 731 min_layer_height = 0.07
 732 nozzle_diameter = 0.4
 733 octoprint_apikey =
 734 octoprint_host =
 735 printer_notes =
 736 printer_settings_id =
 737 retract_before_travel = 2
 738 retract_before_wipe = 0%
 739 retract_layer_change = 1
 740 retract_length = 2
 741 retract_length_toolchange = 3
 742 retract_lift = 0
 743 retract_lift_above = 1
 744 retract_lift_below = 0
 745 retract_restart_extra = 0.01
 746 retract_restart_extra_toolchange = 0
 747 retract_speed = 40
 748 serial_port =
 749 serial_speed = 250000
 750 single_extruder_multi_material = 0
 751 start_gcode = G28 ; home all axes\n
 752 toolchange_gcode =
 753 use_firmware_retraction = 0
 754 use_relative_e_distances = 0
 755 use_volumetric_e = 0
 756 variable_layer_height = 1
 757 wipe = 0
 758 z_offset = 0
 759
 760 [printer:prusa i3]
 761 bed_shape = 0x0,190x0,190x160,0x160
 762 before_layer_gcode =
 763 between_objects_gcode =
 764 deretract_speed = 0
 765 end_gcode = M104 S0        ; turn off temperature\nM140 S0        ; turn off bed temp \nG28 X0           ; home X axis\nG0 Y190         ; präsent object\nM84               ; disable motors\nM81               ; Power off\n\n
 766 extruder_colour = ""
 767 extruder_offset = 0x0
 768 gcode_flavor = reprap
 769 layer_gcode =
 770 max_layer_height = 0
 771 min_layer_height = 0.07
 772 nozzle_diameter = 0.4
 773 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
 774 octoprint_host =
 775 printer_notes =
 776 retract_before_travel = 2
 777 retract_before_wipe = 0%
 778 retract_layer_change = 1
 779 retract_length = 4
 780 retract_length_toolchange = 10
 781 retract_lift = 0
 782 retract_lift_above = 0
 783 retract_lift_below = 0
 784 retract_restart_extra = 0
 785 retract_restart_extra_toolchange = 0
 786 retract_speed = 40
 787 serial_port =
 788 serial_speed = 250000
 789 single_extruder_multi_material = 0
 790 start_gcode = G28 Z             ; home Z\n;G0 Z1            ; lift Z\nG28 X Y         ; home X Y\nG0   Y40        ; clab move
 791 toolchange_gcode = M83 ; turn on relative movement for extruder  \nG1 E-5  ; retract filament 5mm  \nG1 X10 Y10 Z4.000000  ; home X and Y axis leave Z at current height  \nM84 E ; release extruder stepper motor from 'holding' position  \n@pause ; pause print!  \nG1 E0 ; reset extruder, ready to push out plastic again  \nM82 ; set extruder movement back to absolute ready for next layer
 792 use_firmware_retraction = 0
 793 use_relative_e_distances = 0
 794 use_volumetric_e = 0
 795 variable_layer_height = 1
 796 wipe = 0
 797 z_offset = 0
 798
 799 [presets]
 800 print = Tiny print
 801 printer = Tiny
 802 filament = PETG 175