Folgen Tracking Doodle
[stratum0-wiki.git] / RepRap%2FConfigs%2FSlic3r.mw
1 Eine Seite um (gute) Beispielkonfigkurationen zu sammeln, am besten mit Beispieldruck (Foto)
2
3 Es gibt vermutlich nicht ''die eine Ideal-Konfiguration'' die für alle Teile gut funktioniert, mit den hier gelisteten sollte aber ein Druck einigermaßen gelingen.
4
5 ===== Von larsan =====
6 Ursprünglich die erste Konfiguration für unseren Drucker auf Basis von {{Benutzer|DanielWillmann}}s Konfiguration.
7
8 Von der unten stehenden Config gibt es eine verbesserte [https://rohieb.name/stuff/stratum0/larsan-tuned.ini larsan-tuned.ini], die Rohieb gemacht hat.
9
10 <pre style="height:200px;overflow:scroll;">
11 # generated by Slic3r 0.9.8-dev on Wed Nov 28 08:03:30 2012
12 acceleration = 0
13 bed_size = 180,200
14 bed_temperature = 50
15 bottom_solid_layers = 3
16 bridge_fan_speed = 100
17 bridge_flow_ratio = 1
18 bridge_speed = 60
19 brim_width = 0
20 complete_objects =
21 cooling =
22 disable_fan_first_layers = 1
23 duplicate = 1
24 duplicate_distance = 6
25 duplicate_grid = 1,1
26 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
27 external_perimeter_speed = 40%
28 extra_perimeters = 1
29 extruder_clearance_height = 20
30 extruder_clearance_radius = 30
31 extruder_offset = 0x0
32 extrusion_axis = E
33 extrusion_multiplier = 1
34 extrusion_width = 0
35 fan_always_on = 0
36 fan_below_layer_time = 60
37 filament_diameter = 1.75
38 fill_angle = 0
39 fill_density = 0.15
40 fill_pattern = honeycomb
41 first_layer_bed_temperature = 50
42 first_layer_extrusion_width = 0
43 first_layer_height = 0.27
44 first_layer_speed = 15%
45 first_layer_temperature = 195
46 g0 = 0
47 gap_fill_speed = 20
48 gcode_arcs = 0
49 gcode_comments = 0
50 gcode_flavor = reprap
51 infill_acceleration = 50
52 infill_every_layers = 1
53 infill_extruder = 1
54 infill_extrusion_width = 0
55 infill_speed = 60
56 layer_gcode =
57 layer_height = 0.24
58 max_fan_speed = 100
59 min_fan_speed = 35
60 min_print_speed = 5
61 min_skirt_length = 0
62 notes = larsanconfig
63 nozzle_diameter = 0.35
64 only_retract_when_crossing_perimeters =
65 output_filename_format = [input_filename_base].gcode
66 perimeter_acceleration = 25
67 perimeter_extruder = 1
68 perimeter_extrusion_width = 0
69 perimeter_speed = 50
70 perimeters = 3
71 post_process =
72 print_center = 90,100
73 randomize_start = 1
74 retract_before_travel = 5
75 retract_length = 2
76 retract_length_toolchange = 3
77 retract_lift = 0
78 retract_restart_extra = 0.01
79 retract_restart_extra_toolchange = 0
80 retract_speed = 50
81 rotate = 0
82 scale = 1
83 skirt_distance = 20
84 skirt_height = 1
85 skirts = 3
86 slowdown_below_layer_time = 50
87 small_perimeter_speed = 100%
88 solid_fill_pattern = rectilinear
89 solid_infill_below_area = 0
90 solid_infill_every_layers = 0
91 solid_infill_speed = 90%
92 start_gcode = G28 ; home all axes\nM92 E820
93 support_material =
94 support_material_angle = 45
95 support_material_extruder = 1
96 support_material_extrusion_width = 0
97 support_material_pattern = rectilinear
98 support_material_spacing = 2
99 support_material_speed = 60
100 support_material_threshold = 41
101 temperature = 185
102 threads = 2
103 top_solid_infill_speed = 70%
104 top_solid_layers = 3
105 travel_speed = 50
106 use_relative_e_distances = 0
107 vibration_limit = 0
108 z_offset = 0
109 </pre>
110
111 == Schnelle Config von [[Benutzer:Daniel Bohrer|Daniel Bohrer]] (Work in Progress) ==
112 Der erste und letzte Layer wird "normal schnell" gedruckt, die anderen doppelt so schnell. Bei dünnen Strukturen (z.B. Mate-Tags) muss man notfalls noch ein bisschen mit der Perimeteranzahl spielen.
113 <pre style="height:200px;overflow:scroll;">
114 # generated by Slic3r 0.9.4-dev on Fri Nov 16 20:55:02 2012
115 acceleration = 0
116 bed_size = 180,200
117 bed_temperature = 60
118 bridge_fan_speed = 100
119 bridge_flow_ratio = 1
120 bridge_speed = 350
121 brim_width = 0
122 complete_objects = 0
123 cooling = 1
124 disable_fan_first_layers = 1
125 duplicate = 1
126 duplicate_distance = 6
127 duplicate_grid = 1,1
128 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
129 external_perimeter_speed = 90%
130 extra_perimeters = 1
131 extruder_clearance_height = 20
132 extruder_clearance_radius = 20
133 extruder_offset = 0x0
134 extrusion_axis = E
135 extrusion_multiplier = 1.0
136 extrusion_width = 0
137 fan_always_on = 0
138 fan_below_layer_time = 60
139 filament_diameter = 1.75
140 fill_angle = 0
141 fill_density = 0.2
142 fill_pattern = rectilinear
143 first_layer_bed_temperature = 60
144 first_layer_extrusion_width = 0
145 first_layer_height = 100%
146 first_layer_speed = 20%
147 first_layer_temperature = 195
148 g0 = 0
149 gcode_arcs = 0
150 gcode_comments = 0
151 gcode_flavor = reprap
152 infill_acceleration = 50
153 infill_every_layers = 1
154 infill_extruder = 1
155 infill_extrusion_width = 0
156 infill_speed = 120
157 layer_gcode =
158 layer_height = 0.25
159 max_fan_speed = 100
160 min_fan_speed = 35
161 min_print_speed = 10
162 notes = Used for Mate name tag
163 nozzle_diameter = 0.35
164 only_retract_when_crossing_perimeters = 0
165 output_filename_format = [input_filename_base].gcode
166 perimeter_acceleration = 25
167 perimeter_extruder = 1
168 perimeter_extrusion_width = 0
169 perimeter_speed = 100
170 perimeters = 2
171 post_process =
172 print_center = 90,100
173 randomize_start = 1
174 retract_before_travel = 4
175 retract_length = 4
176 retract_length_toolchange = 3
177 retract_lift = 0.5
178 retract_restart_extra = 0
179 retract_restart_extra_toolchange = 0
180 retract_speed = 150
181 rotate = 0
182 scale = 1
183 skirt_distance = 10
184 skirt_height = 1
185 skirts = 2
186 slowdown_below_layer_time = 60
187 small_perimeter_speed = 80%
188 solid_fill_pattern = rectilinear
189 solid_infill_below_area = 0
190 solid_infill_every_layers = 0
191 solid_infill_speed = 100%
192 solid_layers = 3
193 start_gcode = G28 ; home all axes\nM92 E820
194 support_material = 1
195 support_material_angle = 45
196 support_material_extruder = 1
197 support_material_extrusion_width = 0
198 support_material_pattern = rectilinear
199 support_material_spacing = 3
200 support_material_threshold = 45
201 temperature = 185
202 threads = 3
203 top_solid_infill_speed = 50%
204 travel_speed = 140
205 use_relative_e_distances = 0
206 z_offset = 0.22
207 </pre>
208
209 == von Chrissi^ ==
210 * Nette Konfiguration zum Drucken von allem möglichen.
211 * First Layer ist super langsam => Guter Druck auch bei kleinen Strukturen
212 * First Layer Extrusion Width 110% => Wenig ''Wellenschlagen'' auf dem ersten Layer
213 <pre style="height:200px;overflow:scroll;">
214 # generated by Slic3r 0.9.3 on Tue Nov 6 21:53:43 2012
215 acceleration = 0
216 bed_size = 180,200
217 bed_temperature = 60
218 bridge_fan_speed = 100
219 bridge_flow_ratio = 1.05
220 bridge_speed = 60
221 brim_width = 0
222 complete_objects =
223 cooling = 1
224 disable_fan_first_layers = 1
225 duplicate = 1
226 duplicate_distance = 6
227 duplicate_grid = 1,1
228 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
229 external_perimeter_speed = 100%
230 extra_perimeters = 1
231 extruder_clearance_height = 20
232 extruder_clearance_radius = 30
233 extruder_offset = 0x0
234 extrusion_axis = E
235 extrusion_multiplier = 1
236 extrusion_width = 100%
237 fan_always_on = 0
238 fan_below_layer_time = 60
239 filament_diameter = 1.75
240 fill_angle = 45
241 fill_density = 0.1
242 fill_pattern = rectilinear
243 first_layer_bed_temperature = 60
244 first_layer_extrusion_width = 112%
245 first_layer_height = 95%
246 first_layer_speed = 15%
247 first_layer_temperature = 200
248 g0 = 0
249 gcode_arcs = 0
250 gcode_comments = 0
251 gcode_flavor = reprap
252 infill_acceleration = 50
253 infill_every_layers = 1
254 infill_extruder = 1
255 infill_extrusion_width = 120%
256 infill_speed = 60
257 layer_gcode =
258 layer_height = 0.3
259 max_fan_speed = 100
260 min_fan_speed = 35
261 min_print_speed = 5
262 notes = larsanconfig
263 nozzle_diameter = 0.35
264 only_retract_when_crossing_perimeters = 1
265 output_filename_format = [timestamp]_[input_filename_base].gcode
266 perimeter_acceleration = 25
267 perimeter_extruder = 1
268 perimeter_extrusion_width = 0
269 perimeter_speed = 60
270 perimeters = 2
271 post_process =
272 print_center = 120,120
273 randomize_start = 1
274 retract_before_travel = 4
275 retract_length = 2
276 retract_length_toolchange = 3
277 retract_lift = 0
278 retract_restart_extra = 0
279 retract_restart_extra_toolchange = 0
280 retract_speed = 50
281 rotate = 0
282 scale = 1
283 skirt_distance = 10
284 skirt_height = 1
285 skirts = 3
286 slowdown_below_layer_time = 50
287 small_perimeter_speed = 50%
288 solid_fill_pattern = rectilinear
289 solid_infill_below_area = 0
290 solid_infill_every_layers = 0
291 solid_infill_speed = 100%
292 solid_layers = 3
293 start_gcode = G28 ; home all axes\nM92 E820
294 support_material = 1
295 support_material_angle = 45
296 support_material_extruder = 1
297 support_material_extrusion_width = 160%
298 support_material_pattern = rectilinear
299 support_material_spacing = 2
300 support_material_threshold = 40
301 temperature = 205
302 threads = 2
303 top_solid_infill_speed = 40%
304 travel_speed = 90
305 use_relative_e_distances = 0
306 z_offset = 0
307 </pre>
308
309 == Gelbes Filament ==
310 * Ursprünglich für [[Reprap/Parent]] erstellt
311 * Damit gedruckt: der letzte gelbe frame-vertex für den Drucker
312 * etwas wärmer (195°C)
313 * 0.22 mm z-offeset
314 <pre style="height:200px;overflow:scroll;">
315 acceleration = 0
316 bed_size = 170,170
317 bed_temperature = 60
318 bridge_fan_speed = 100
319 bridge_flow_ratio = 1
320 bridge_speed = 30
321 brim_width = 0
322 complete_objects = 0
323 cooling = 1
324 disable_fan_first_layers = 1
325 duplicate = 1
326 duplicate_distance = 6
327 duplicate_grid = 1,1
328 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
329 external_perimeter_speed = 90%
330 extra_perimeters = 1
331 extruder_clearance_height = 20
332 extruder_clearance_radius = 20
333 extrusion_axis = E
334 extrusion_multiplier = 1
335 extrusion_width = 0
336 fan_always_on = 0
337 fan_below_layer_time = 60
338 filament_diameter = 3
339 fill_angle = 45
340 fill_density = 0.15
341 fill_pattern = rectilinear
342 first_layer_bed_temperature = 60
343 first_layer_extrusion_width = 0
344 first_layer_height = 115%
345 first_layer_speed = 80%
346 first_layer_temperature = 200
347 g0 = 0
348 gcode_arcs = 0
349 gcode_comments = 0
350 gcode_flavor = reprap
351 infill_acceleration = 50
352 infill_every_layers = 1
353 infill_extruder = 1
354 infill_extrusion_width = 0
355 infill_speed = 40
356 layer_gcode =
357 layer_height = 0.28
358 max_fan_speed = 100
359 min_fan_speed = 35
360 min_print_speed = 10
361 notes = Used for Mate name tag
362 nozzle_diameter = 0.35
363 output_filename_format = [input_filename_base].gcode
364 perimeter_acceleration = 25
365 perimeter_speed = 30
366 perimeters = 3
367 perimeters_extruder = 1
368 perimeters_extrusion_width = 0
369 post_process =
370 print_center = 50,27
371 randomize_start = 1
372 retract_before_travel = 4
373 retract_length = 3
374 retract_lift = 0.4
375 retract_restart_extra = 0
376 retract_speed = 30
377 rotate = 0
378 scale = 1
379 skirt_distance = 6
380 skirt_height = 1
381 skirts = 3
382 slowdown_below_layer_time = 60
383 small_perimeter_speed = 30
384 solid_fill_pattern = rectilinear
385 solid_infill_speed = 40
386 solid_layers = 3
387 start_gcode = G28 ; home all axes\nM92 E820
388 support_material =
389 support_material_angle = 45
390 support_material_extruder = 1
391 support_material_extrusion_width = 0
392 support_material_pattern = rectilinear
393 support_material_spacing = 2.5
394 support_material_threshold = 45
395 temperature = 195
396 threads = 2
397 top_solid_infill_speed = 40
398 travel_speed = 130
399 use_relative_e_distances = 0
400 z_offset = 0.22
401 </pre>
402
403 == RepRap-Config ==
404 Konfiguration, mit der die Teile für den RepRap vom [http://netz39.eu Netz39] gedruckt wurden.
405 <pre style="height:200px;overflow:scroll;">
406 # generated by Slic3r 0.9.9-dev on Mon Jun 3 17:06:48 2013
407 avoid_crossing_perimeters = 0
408 bed_size = 180,200
409 bed_temperature = 50
410 bottom_solid_layers = 5
411 bridge_acceleration = 0
412 bridge_fan_speed = 100
413 bridge_flow_ratio = 1
414 bridge_speed = 30
415 brim_width = 0
416 complete_objects = 1
417 cooling =
418 default_acceleration = 0
419 disable_fan_first_layers = 1
420 duplicate = 1
421 duplicate_distance = 6
422 duplicate_grid = 1,1
423 end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0 ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84 ; disable motors
424 external_perimeter_speed = 40%
425 external_perimeters_first = 0
426 extra_perimeters =
427 extruder_clearance_height = 35
428 extruder_clearance_radius = 62
429 extruder_offset = 0x0
430 extrusion_axis = E
431 extrusion_multiplier = 1.1
432 extrusion_width = 0
433 fan_always_on = 0
434 fan_below_layer_time = 60
435 filament_diameter = 1.75
436 fill_angle = 30
437 fill_density = 0.5
438 fill_pattern = rectilinear
439 first_layer_bed_temperature = 50
440 first_layer_extrusion_width = 0
441 first_layer_height = 150%
442 first_layer_speed = 40%
443 first_layer_temperature = 197
444 g0 = 0
445 gap_fill_speed = 20
446 gcode_arcs = 0
447 gcode_comments = 0
448 gcode_flavor = reprap
449 infill_acceleration = 0
450 infill_every_layers = 1
451 infill_extruder = 1
452 infill_extrusion_width = 0
453 infill_first = 0
454 infill_only_where_needed = 0
455 infill_speed = 60
456 layer_gcode =
457 layer_height = 0.2
458 max_fan_speed = 100
459 min_fan_speed = 35
460 min_print_speed = 5
461 min_skirt_length = 15
462 notes = config for printing netz39 pieces
463 nozzle_diameter = 0.33
464 only_retract_when_crossing_perimeters = 1
465 output_filename_format = [input_filename_base].gcode
466 perimeter_acceleration = 0
467 perimeter_extruder = 1
468 perimeter_extrusion_width = 0
469 perimeter_speed = 60
470 perimeters = 3
471 post_process =
472 print_center = 90,100
473 raft_layers = 0
474 randomize_start =
475 resolution = 0
476 retract_before_travel = 0
477 retract_layer_change = 1
478 retract_length = 2
479 retract_length_toolchange = 5
480 retract_lift = 0
481 retract_restart_extra = 0
482 retract_restart_extra_toolchange = 0
483 retract_speed = 50
484 rotate = 0
485 scale = 1
486 skirt_distance = 5
487 skirt_height = 1
488 skirts = 2
489 slowdown_below_layer_time = 50
490 small_perimeter_speed = 60%
491 solid_fill_pattern = rectilinear
492 solid_infill_below_area = 0
493 solid_infill_every_layers = 0
494 solid_infill_extrusion_width = 0
495 solid_infill_speed = 100%
496 start_gcode = G28 ; home all axes\nM92 E820
497 support_material =
498 support_material_angle = 45
499 support_material_enforce_layers = 0
500 support_material_extruder = 1
501 support_material_extrusion_width = 0
502 support_material_interface_layers = 0
503 support_material_interface_spacing = 0
504 support_material_pattern = rectilinear
505 support_material_spacing = 2
506 support_material_speed = 60
507 support_material_threshold = 41
508 temperature = 188
509 threads = 2
510 toolchange_gcode =
511 top_infill_extrusion_width = 0
512 top_solid_infill_speed = 70%
513 top_solid_layers = 5
514 travel_speed = 100
515 use_relative_e_distances = 0
516 vibration_limit = 0
517 z_offset = 0
518 </pre>
519
520 [[Kategorie:RepRap]]
This page took 0.064728 seconds and 5 git commands to generate.