3D-Drucker%2FSlicerBundle.ini.mw

   1 # generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016
   2
   3 [filament:LULZBOT ABS fine]
   4 bed_temperature = 100
   5 bridge_fan_speed = 0
   6 cooling = 1
   7 disable_fan_first_layers = 1
   8 extrusion_multiplier = 1
   9 fan_always_on = 0
  10 fan_below_layer_time = 60
  11 filament_colour = #FFFFFF
  12 filament_diameter = 2.89
  13 first_layer_bed_temperature = 100
  14 first_layer_temperature = 250
  15 max_fan_speed = 0
  16 min_fan_speed = 0
  17 min_print_speed = 15
  18 slowdown_below_layer_time = 20
  19 temperature = 240
  20
  21 [filament:MendelPro ABS]
  22 bed_temperature = 0
  23 bridge_fan_speed = 100
  24 cooling = 0
  25 disable_fan_first_layers = 1
  26 extrusion_multiplier = 1
  27 fan_always_on = 0
  28 fan_below_layer_time = 60
  29 filament_colour = #FFFFFF
  30 filament_diameter = 1.7
  31 first_layer_bed_temperature = 0
  32 first_layer_temperature = 250
  33 max_fan_speed = 100
  34 min_fan_speed = 50
  35 min_print_speed = 5
  36 slowdown_below_layer_time = 30
  37 temperature = 245
  38
  39 [filament:MendelPro Holz]
  40 bed_temperature = 50
  41 bridge_fan_speed = 100
  42 cooling = 1
  43 disable_fan_first_layers = 1
  44 extrusion_multiplier = 1
  45 fan_always_on = 1
  46 fan_below_layer_time = 60
  47 filament_colour = #FFFFFF
  48 filament_diameter = 1.7
  49 first_layer_bed_temperature = 55
  50 first_layer_temperature = 200
  51 max_fan_speed = 100
  52 min_fan_speed = 50
  53 min_print_speed = 5
  54 slowdown_below_layer_time = 30
  55 temperature = 185
  56
  57 [filament:MendelPro PLA]
  58 bed_temperature = 50
  59 bridge_fan_speed = 100
  60 cooling = 1
  61 disable_fan_first_layers = 1
  62 extrusion_multiplier = 1
  63 fan_always_on = 1
  64 fan_below_layer_time = 60
  65 filament_colour = #FFFFFF
  66 filament_diameter = 1.7
  67 first_layer_bed_temperature = 55
  68 first_layer_temperature = 200
  69 max_fan_speed = 100
  70 min_fan_speed = 50
  71 min_print_speed = 5
  72 slowdown_below_layer_time = 30
  73 temperature = 180
  74
  75 [filament:TinyBoy PLA]
  76 bed_temperature = 0
  77 bridge_fan_speed = 100
  78 cooling = 1
  79 disable_fan_first_layers = 2
  80 extrusion_multiplier = 0.9
  81 fan_always_on = 1
  82 fan_below_layer_time = 60
  83 filament_colour = #35E1FF
  84 filament_diameter = 1.7
  85 first_layer_bed_temperature = 0
  86 first_layer_temperature = 200
  87 max_fan_speed = 50
  88 min_fan_speed = 35
  89 min_print_speed = 5
  90 slowdown_below_layer_time = 15
  91 temperature = 185
  92
  93 [filament:prusa i3 PLA black fine]
  94 bed_temperature = 50
  95 bridge_fan_speed = 100
  96 cooling = 1
  97 disable_fan_first_layers = 1
  98 extrusion_multiplier = 1
  99 fan_always_on = 1
 100 fan_below_layer_time = 60
 101 filament_colour = #FF0000
 102 filament_diameter = 2.9
 103 first_layer_bed_temperature = 50
 104 first_layer_temperature = 200
 105 max_fan_speed = 100
 106 min_fan_speed = 100
 107 min_print_speed = 5
 108 slowdown_below_layer_time = 15
 109 temperature = 200
 110
 111 [filament:prusa i3 PLA igus]
 112 bed_temperature = 50
 113 bridge_fan_speed = 100
 114 cooling = 0
 115 disable_fan_first_layers = 1
 116 extrusion_multiplier = 0.9
 117 fan_always_on = 0
 118 fan_below_layer_time = 60
 119 filament_colour = #D0C9B0
 120 filament_diameter = 2.9
 121 first_layer_bed_temperature = 50
 122 first_layer_temperature = 250
 123 max_fan_speed = 100
 124 min_fan_speed = 35
 125 min_print_speed = 5
 126 slowdown_below_layer_time = 15
 127 temperature = 250
 128
 129 [filament:prusa i3 PLA rot]
 130 bed_temperature = 50
 131 bridge_fan_speed = 100
 132 cooling = 1
 133 disable_fan_first_layers = 1
 134 extrusion_multiplier = 1
 135 fan_always_on = 1
 136 fan_below_layer_time = 60
 137 filament_colour = #FF0000
 138 filament_diameter = 2.9
 139 first_layer_bed_temperature = 50
 140 first_layer_temperature = 200
 141 max_fan_speed = 100
 142 min_fan_speed = 35
 143 min_print_speed = 5
 144 slowdown_below_layer_time = 15
 145 temperature = 200
 146
 147 [presets]
 148 filament = LULZBOT ABS fine.ini
 149 print = prusa i3 100.ini
 150 printer = LULZBOT ABS fine.ini
 151
 152 [print:LULZBOT ABS fine  ]
 153 avoid_crossing_perimeters = 1
 154 bottom_solid_layers = 2
 155 bridge_acceleration = 1000
 156 bridge_flow_ratio = 1.1
 157 bridge_speed = 40
 158 brim_width = 0
 159 complete_objects = 0
 160 default_acceleration = 900
 161 dont_support_bridges = 1
 162 external_fill_pattern = rectilinear
 163 external_perimeter_extrusion_width = 0
 164 external_perimeter_speed = 30
 165 external_perimeters_first = 0
 166 extra_perimeters = 1
 167 extruder_clearance_height = 20
 168 extruder_clearance_radius = 20
 169 extrusion_width = 0.37
 170 fill_angle = 35
 171 fill_density = 30%
 172 fill_pattern = line
 173 first_layer_acceleration = 0
 174 first_layer_extrusion_width = 0.37
 175 first_layer_height = 120%
 176 first_layer_speed = 85%
 177 gap_fill_speed = 45
 178 gcode_comments = 0
 179 infill_acceleration = 1400
 180 infill_every_layers = 2
 181 infill_extruder = 1
 182 infill_extrusion_width = 0.6
 183 infill_first = 0
 184 infill_only_where_needed = 0
 185 infill_overlap = 15%
 186 infill_speed = 70
 187 interface_shells = 0
 188 layer_height = 0.14
 189 max_print_speed = 80
 190 max_volumetric_speed = 0
 191 min_skirt_length = 0
 192 notes =
 193 only_retract_when_crossing_perimeters = 0
 194 ooze_prevention = 0
 195 output_filename_format = [input_filename_base].gcode
 196 overhangs = 1
 197 perimeter_acceleration = 900
 198 perimeter_extruder = 1
 199 perimeter_extrusion_width = 0.34
 200 perimeter_speed = 40
 201 perimeters = 4
 202 post_process =
 203 raft_layers = 0
 204 resolution = 0
 205 seam_position = aligned
 206 skirt_distance = 6
 207 skirt_height = 1
 208 skirts = 2
 209 small_perimeter_speed = 30
 210 solid_infill_below_area = 30
 211 solid_infill_every_layers = 0
 212 solid_infill_extruder = 1
 213 solid_infill_extrusion_width = 0
 214 solid_infill_speed = 60
 215 spiral_vase = 0
 216 standby_temperature_delta = -5
 217 support_material = 0
 218 support_material_angle = 0
 219 support_material_contact_distance = 0.2
 220 support_material_enforce_layers = 0
 221 support_material_extruder = 1
 222 support_material_extrusion_width = 0
 223 support_material_interface_extruder = 1
 224 support_material_interface_layers = 0
 225 support_material_interface_spacing = 0
 226 support_material_interface_speed = 100%
 227 support_material_pattern = rectilinear
 228 support_material_spacing = 2.5
 229 support_material_speed = 60
 230 support_material_threshold = 45
 231 thin_walls = 1
 232 threads = 2
 233 top_infill_extrusion_width = 0.35
 234 top_solid_infill_speed = 80%
 235 top_solid_layers = 4
 236 travel_speed = 80
 237 xy_size_compensation = 0
 238
 239 [print:MendelPro]
 240 avoid_crossing_perimeters = 0
 241 bottom_solid_layers = 3
 242 bridge_acceleration = 0
 243 bridge_flow_ratio = 1
 244 bridge_speed = 35
 245 brim_width = 0
 246 complete_objects = 0
 247 default_acceleration = 0
 248 dont_support_bridges = 1
 249 external_fill_pattern = rectilinear
 250 external_perimeter_extrusion_width = 0
 251 external_perimeter_speed = 20
 252 external_perimeters_first = 0
 253 extra_perimeters = 1
 254 extruder_clearance_height = 20
 255 extruder_clearance_radius = 20
 256 extrusion_width = 0
 257 fill_angle = 45
 258 fill_density = 15%
 259 fill_pattern = rectilinear
 260 first_layer_acceleration = 0
 261 first_layer_extrusion_width = 150%
 262 first_layer_height = 0.2
 263 first_layer_speed = 10
 264 gap_fill_speed = 10
 265 gcode_comments = 0
 266 infill_acceleration = 0
 267 infill_every_layers = 1
 268 infill_extruder = 1
 269 infill_extrusion_width = 0
 270 infill_first = 0
 271 infill_only_where_needed = 0
 272 infill_overlap = 15%
 273 infill_speed = 0
 274 interface_shells = 0
 275 layer_height = 0.2
 276 max_print_speed = 35
 277 max_volumetric_speed = 0
 278 min_skirt_length = 1
 279 notes =
 280 only_retract_when_crossing_perimeters = 1
 281 ooze_prevention = 0
 282 output_filename_format = [input_filename_base].gcode
 283 overhangs = 1
 284 perimeter_acceleration = 0
 285 perimeter_extruder = 1
 286 perimeter_extrusion_width = 0
 287 perimeter_speed = 0
 288 perimeters = 2
 289 post_process =
 290 raft_layers = 0
 291 resolution = 0
 292 seam_position = aligned
 293 skirt_distance = 1
 294 skirt_height = 1
 295 skirts = 1
 296 small_perimeter_speed = 10
 297 solid_infill_below_area = 70
 298 solid_infill_every_layers = 0
 299 solid_infill_extruder = 1
 300 solid_infill_extrusion_width = 0
 301 solid_infill_speed = 0
 302 spiral_vase = 0
 303 standby_temperature_delta = -5
 304 support_material = 0
 305 support_material_angle = 0
 306 support_material_contact_distance = 0.2
 307 support_material_enforce_layers = 0
 308 support_material_extruder = 1
 309 support_material_extrusion_width = 0
 310 support_material_interface_extruder = 1
 311 support_material_interface_layers = 2
 312 support_material_interface_spacing = 0
 313 support_material_interface_speed = 100%
 314 support_material_pattern = rectilinear
 315 support_material_spacing = 5
 316 support_material_speed = 0
 317 support_material_threshold = 40
 318 thin_walls = 1
 319 threads = 2
 320 top_infill_extrusion_width = 0
 321 top_solid_infill_speed = 20
 322 top_solid_layers = 3
 323 travel_speed = 100
 324 xy_size_compensation = 0
 325
 326 [print:TinyBoy]
 327 avoid_crossing_perimeters = 0
 328 bottom_solid_layers = 3
 329 bridge_acceleration = 0
 330 bridge_flow_ratio = 1
 331 bridge_speed = 0
 332 brim_width = 0
 333 complete_objects = 0
 334 default_acceleration = 0
 335 dont_support_bridges = 1
 336 external_fill_pattern = rectilinear
 337 external_perimeter_extrusion_width = 0
 338 external_perimeter_speed = 0
 339 external_perimeters_first = 0
 340 extra_perimeters = 1
 341 extruder_clearance_height = 20
 342 extruder_clearance_radius = 20
 343 extrusion_width = 0
 344 fill_angle = 45
 345 fill_density = 15%
 346 fill_pattern = rectilinear
 347 first_layer_acceleration = 0
 348 first_layer_extrusion_width = 150%
 349 first_layer_height = 0.2
 350 first_layer_speed = 20
 351 gap_fill_speed = 0
 352 gcode_comments = 0
 353 infill_acceleration = 0
 354 infill_every_layers = 1
 355 infill_extruder = 1
 356 infill_extrusion_width = 0
 357 infill_first = 0
 358 infill_only_where_needed = 0
 359 infill_overlap = 15%
 360 infill_speed = 0
 361 interface_shells = 0
 362 layer_height = 0.2
 363 max_print_speed = 50
 364 max_volumetric_speed = 0
 365 min_skirt_length = 1
 366 notes =
 367 only_retract_when_crossing_perimeters = 1
 368 ooze_prevention = 0
 369 output_filename_format = [input_filename_base].gcode
 370 overhangs = 1
 371 perimeter_acceleration = 0
 372 perimeter_extruder = 1
 373 perimeter_extrusion_width = 0
 374 perimeter_speed = 0
 375 perimeters = 2
 376 post_process =
 377 raft_layers = 0
 378 resolution = 0
 379 seam_position = aligned
 380 skirt_distance = 1
 381 skirt_height = 1
 382 skirts = 1
 383 small_perimeter_speed = 0
 384 solid_infill_below_area = 70
 385 solid_infill_every_layers = 0
 386 solid_infill_extruder = 1
 387 solid_infill_extrusion_width = 0
 388 solid_infill_speed = 0
 389 spiral_vase = 0
 390 standby_temperature_delta = -5
 391 support_material = 0
 392 support_material_angle = 0
 393 support_material_contact_distance = 0.2
 394 support_material_enforce_layers = 0
 395 support_material_extruder = 1
 396 support_material_extrusion_width = 0
 397 support_material_interface_extruder = 1
 398 support_material_interface_layers = 2
 399 support_material_interface_spacing = 0
 400 support_material_interface_speed = 100%
 401 support_material_pattern = rectilinear
 402 support_material_spacing = 5
 403 support_material_speed = 0
 404 support_material_threshold = 40
 405 thin_walls = 1
 406 threads = 2
 407 top_infill_extrusion_width = 0
 408 top_solid_infill_speed = 0
 409 top_solid_layers = 3
 410 travel_speed = 100
 411 xy_size_compensation = 0
 412
 413 [print:prusa i3 100]
 414 avoid_crossing_perimeters = 0
 415 bottom_solid_layers = 3
 416 bridge_acceleration = 0
 417 bridge_flow_ratio = 1
 418 bridge_speed = 40
 419 brim_width = 0
 420 complete_objects = 0
 421 default_acceleration = 0
 422 dont_support_bridges = 1
 423 external_fill_pattern = rectilinear
 424 external_perimeter_extrusion_width = 0
 425 external_perimeter_speed = 10
 426 external_perimeters_first = 0
 427 extra_perimeters = 1
 428 extruder_clearance_height = 20
 429 extruder_clearance_radius = 20
 430 extrusion_width = 0
 431 fill_angle = 45
 432 fill_density = 20%
 433 fill_pattern = rectilinear
 434 first_layer_acceleration = 0
 435 first_layer_extrusion_width = 0
 436 first_layer_height = 0.2
 437 first_layer_speed = 10
 438 gap_fill_speed = 10
 439 gcode_comments = 0
 440 infill_acceleration = 0
 441 infill_every_layers = 1
 442 infill_extruder = 1
 443 infill_extrusion_width = 110%
 444 infill_first = 0
 445 infill_only_where_needed = 0
 446 infill_overlap = 15%
 447 infill_speed = 0
 448 interface_shells = 0
 449 layer_height = 0.1
 450 max_print_speed = 80
 451 max_volumetric_speed = 0
 452 min_skirt_length = 1
 453 notes =
 454 only_retract_when_crossing_perimeters = 1
 455 ooze_prevention = 0
 456 output_filename_format = [input_filename_base].gcode
 457 overhangs = 1
 458 perimeter_acceleration = 0
 459 perimeter_extruder = 1
 460 perimeter_extrusion_width = 0
 461 perimeter_speed = 0
 462 perimeters = 3
 463 post_process =
 464 raft_layers = 0
 465 resolution = 0
 466 seam_position = aligned
 467 skirt_distance = 6
 468 skirt_height = 1
 469 skirts = 3
 470 small_perimeter_speed = 10
 471 solid_infill_below_area = 70
 472 solid_infill_every_layers = 0
 473 solid_infill_extruder = 1
 474 solid_infill_extrusion_width = 0
 475 solid_infill_speed = 0
 476 spiral_vase = 0
 477 standby_temperature_delta = -5
 478 support_material = 0
 479 support_material_angle = 0
 480 support_material_contact_distance = 0.2
 481 support_material_enforce_layers = 0
 482 support_material_extruder = 1
 483 support_material_extrusion_width = 0
 484 support_material_interface_extruder = 1
 485 support_material_interface_layers = 2
 486 support_material_interface_spacing = 0
 487 support_material_interface_speed = 100%
 488 support_material_pattern = rectilinear
 489 support_material_spacing = 5
 490 support_material_speed = 0
 491 support_material_threshold = 40
 492 thin_walls = 1
 493 threads = 2
 494 top_infill_extrusion_width = 0
 495 top_solid_infill_speed = 10
 496 top_solid_layers = 3
 497 travel_speed = 100
 498 xy_size_compensation = 0
 499
 500 [print:prusa i3 100 testtesttest]
 501 avoid_crossing_perimeters = 0
 502 bottom_solid_layers = 0
 503 bridge_acceleration = 0
 504 bridge_flow_ratio = 1
 505 bridge_speed = 40
 506 brim_width = 0
 507 complete_objects = 0
 508 default_acceleration = 0
 509 dont_support_bridges = 1
 510 external_fill_pattern = rectilinear
 511 external_perimeter_extrusion_width = 0
 512 external_perimeter_speed = 10
 513 external_perimeters_first = 0
 514 extra_perimeters = 1
 515 extruder_clearance_height = 20
 516 extruder_clearance_radius = 20
 517 extrusion_width = 0
 518 fill_angle = 45
 519 fill_density = 0%
 520 fill_pattern = rectilinear
 521 first_layer_acceleration = 0
 522 first_layer_extrusion_width = 0
 523 first_layer_height = 0.2
 524 first_layer_speed = 10
 525 gap_fill_speed = 10
 526 gcode_comments = 0
 527 infill_acceleration = 0
 528 infill_every_layers = 1
 529 infill_extruder = 1
 530 infill_extrusion_width = 110%
 531 infill_first = 0
 532 infill_only_where_needed = 0
 533 infill_overlap = 15%
 534 infill_speed = 0
 535 interface_shells = 0
 536 layer_height = 0.1
 537 max_print_speed = 80
 538 max_volumetric_speed = 0
 539 min_skirt_length = 1
 540 notes =
 541 only_retract_when_crossing_perimeters = 1
 542 ooze_prevention = 0
 543 output_filename_format = [input_filename_base].gcode
 544 overhangs = 1
 545 perimeter_acceleration = 0
 546 perimeter_extruder = 1
 547 perimeter_extrusion_width = 0
 548 perimeter_speed = 0
 549 perimeters = 1
 550 post_process =
 551 raft_layers = 0
 552 resolution = 0
 553 seam_position = aligned
 554 skirt_distance = 1
 555 skirt_height = 1
 556 skirts = 1
 557 small_perimeter_speed = 10
 558 solid_infill_below_area = 70
 559 solid_infill_every_layers = 0
 560 solid_infill_extruder = 1
 561 solid_infill_extrusion_width = 0
 562 solid_infill_speed = 0
 563 spiral_vase = 0
 564 standby_temperature_delta = -5
 565 support_material = 0
 566 support_material_angle = 0
 567 support_material_contact_distance = 0.2
 568 support_material_enforce_layers = 0
 569 support_material_extruder = 1
 570 support_material_extrusion_width = 0
 571 support_material_interface_extruder = 1
 572 support_material_interface_layers = 2
 573 support_material_interface_spacing = 0
 574 support_material_interface_speed = 100%
 575 support_material_pattern = rectilinear
 576 support_material_spacing = 5
 577 support_material_speed = 0
 578 support_material_threshold = 40
 579 thin_walls = 1
 580 threads = 2
 581 top_infill_extrusion_width = 0
 582 top_solid_infill_speed = 10
 583 top_solid_layers = 0
 584 travel_speed = 100
 585 xy_size_compensation = 0
 586
 587 [print:prusa i3 250]
 588 avoid_crossing_perimeters = 0
 589 bottom_solid_layers = 3
 590 bridge_acceleration = 0
 591 bridge_flow_ratio = 1
 592 bridge_speed = 40
 593 brim_width = 0
 594 complete_objects = 0
 595 default_acceleration = 0
 596 dont_support_bridges = 1
 597 external_fill_pattern = rectilinear
 598 external_perimeter_extrusion_width = 0
 599 external_perimeter_speed = 10
 600 external_perimeters_first = 0
 601 extra_perimeters = 1
 602 extruder_clearance_height = 20
 603 extruder_clearance_radius = 20
 604 extrusion_width = 0
 605 fill_angle = 45
 606 fill_density = 20%
 607 fill_pattern = rectilinear
 608 first_layer_acceleration = 0
 609 first_layer_extrusion_width = 0
 610 first_layer_height = 0.2
 611 first_layer_speed = 15
 612 gap_fill_speed = 10
 613 gcode_comments = 0
 614 infill_acceleration = 0
 615 infill_every_layers = 1
 616 infill_extruder = 1
 617 infill_extrusion_width = 110%
 618 infill_first = 0
 619 infill_only_where_needed = 0
 620 infill_overlap = 15%
 621 infill_speed = 0
 622 interface_shells = 0
 623 layer_height = 0.25
 624 max_print_speed = 60
 625 max_volumetric_speed = 0
 626 min_skirt_length = 1
 627 notes =
 628 only_retract_when_crossing_perimeters = 1
 629 ooze_prevention = 0
 630 output_filename_format = [input_filename_base].gcode
 631 overhangs = 1
 632 perimeter_acceleration = 0
 633 perimeter_extruder = 1
 634 perimeter_extrusion_width = 0
 635 perimeter_speed = 0
 636 perimeters = 2
 637 post_process =
 638 raft_layers = 0
 639 resolution = 0
 640 seam_position = aligned
 641 skirt_distance = 1
 642 skirt_height = 1
 643 skirts = 1
 644 small_perimeter_speed = 10
 645 solid_infill_below_area = 70
 646 solid_infill_every_layers = 0
 647 solid_infill_extruder = 1
 648 solid_infill_extrusion_width = 0
 649 solid_infill_speed = 0
 650 spiral_vase = 0
 651 standby_temperature_delta = -5
 652 support_material = 0
 653 support_material_angle = 0
 654 support_material_contact_distance = 0.2
 655 support_material_enforce_layers = 0
 656 support_material_extruder = 1
 657 support_material_extrusion_width = 0
 658 support_material_interface_extruder = 1
 659 support_material_interface_layers = 2
 660 support_material_interface_spacing = 0
 661 support_material_interface_speed = 100%
 662 support_material_pattern = rectilinear
 663 support_material_spacing = 5
 664 support_material_speed = 0
 665 support_material_threshold = 40
 666 thin_walls = 1
 667 threads = 2
 668 top_infill_extrusion_width = 0
 669 top_solid_infill_speed = 20
 670 top_solid_layers = 3
 671 travel_speed = 100
 672 xy_size_compensation = 0
 673
 674 [print:prusa i3 400]
 675 avoid_crossing_perimeters = 0
 676 bottom_solid_layers = 3
 677 bridge_acceleration = 0
 678 bridge_flow_ratio = 1
 679 bridge_speed = 60
 680 brim_width = 0
 681 complete_objects = 0
 682 default_acceleration = 0
 683 dont_support_bridges = 1
 684 external_fill_pattern = rectilinear
 685 external_perimeter_extrusion_width = 0
 686 external_perimeter_speed = 20
 687 external_perimeters_first = 0
 688 extra_perimeters = 1
 689 extruder_clearance_height = 20
 690 extruder_clearance_radius = 20
 691 extrusion_width = 0
 692 fill_angle = 45
 693 fill_density = 20%
 694 fill_pattern = rectilinear
 695 first_layer_acceleration = 0
 696 first_layer_extrusion_width = 0
 697 first_layer_height = 0.2
 698 first_layer_speed = 10
 699 gap_fill_speed = 10
 700 gcode_comments = 0
 701 infill_acceleration = 0
 702 infill_every_layers = 1
 703 infill_extruder = 1
 704 infill_extrusion_width = 110%
 705 infill_first = 0
 706 infill_only_where_needed = 0
 707 infill_overlap = 15%
 708 infill_speed = 0
 709 interface_shells = 0
 710 layer_height = 0.4
 711 max_print_speed = 80
 712 max_volumetric_speed = 0
 713 min_skirt_length = 1
 714 notes =
 715 only_retract_when_crossing_perimeters = 1
 716 ooze_prevention = 0
 717 output_filename_format = [input_filename_base].gcode
 718 overhangs = 1
 719 perimeter_acceleration = 0
 720 perimeter_extruder = 1
 721 perimeter_extrusion_width = 0
 722 perimeter_speed = 0
 723 perimeters = 2
 724 post_process =
 725 raft_layers = 0
 726 resolution = 0
 727 seam_position = aligned
 728 skirt_distance = 1
 729 skirt_height = 1
 730 skirts = 1
 731 small_perimeter_speed = 10
 732 solid_infill_below_area = 70
 733 solid_infill_every_layers = 0
 734 solid_infill_extruder = 1
 735 solid_infill_extrusion_width = 0
 736 solid_infill_speed = 0
 737 spiral_vase = 0
 738 standby_temperature_delta = -5
 739 support_material = 0
 740 support_material_angle = 0
 741 support_material_contact_distance = 0.2
 742 support_material_enforce_layers = 0
 743 support_material_extruder = 1
 744 support_material_extrusion_width = 0
 745 support_material_interface_extruder = 1
 746 support_material_interface_layers = 2
 747 support_material_interface_spacing = 0
 748 support_material_interface_speed = 100%
 749 support_material_pattern = rectilinear
 750 support_material_spacing = 5
 751 support_material_speed = 0
 752 support_material_threshold = 40
 753 thin_walls = 1
 754 threads = 2
 755 top_infill_extrusion_width = 0
 756 top_solid_infill_speed = 20
 757 top_solid_layers = 3
 758 travel_speed = 100
 759 xy_size_compensation = 0
 760
 761 [print:prusa i3 400 sup]
 762 avoid_crossing_perimeters = 0
 763 bottom_solid_layers = 3
 764 bridge_acceleration = 0
 765 bridge_flow_ratio = 1
 766 bridge_speed = 40
 767 brim_width = 0
 768 complete_objects = 0
 769 default_acceleration = 0
 770 dont_support_bridges = 1
 771 external_fill_pattern = rectilinear
 772 external_perimeter_extrusion_width = 0
 773 external_perimeter_speed = 10
 774 external_perimeters_first = 0
 775 extra_perimeters = 1
 776 extruder_clearance_height = 20
 777 extruder_clearance_radius = 20
 778 extrusion_width = 0
 779 fill_angle = 45
 780 fill_density = 20%
 781 fill_pattern = rectilinear
 782 first_layer_acceleration = 0
 783 first_layer_extrusion_width = 0
 784 first_layer_height = 0.2
 785 first_layer_speed = 10
 786 gap_fill_speed = 10
 787 gcode_comments = 0
 788 infill_acceleration = 0
 789 infill_every_layers = 1
 790 infill_extruder = 1
 791 infill_extrusion_width = 110%
 792 infill_first = 0
 793 infill_only_where_needed = 0
 794 infill_overlap = 15%
 795 infill_speed = 0
 796 interface_shells = 0
 797 layer_height = 0.4
 798 max_print_speed = 80
 799 max_volumetric_speed = 0
 800 min_skirt_length = 1
 801 notes =
 802 only_retract_when_crossing_perimeters = 1
 803 ooze_prevention = 0
 804 output_filename_format = [input_filename_base].gcode
 805 overhangs = 1
 806 perimeter_acceleration = 0
 807 perimeter_extruder = 1
 808 perimeter_extrusion_width = 0
 809 perimeter_speed = 0
 810 perimeters = 2
 811 post_process =
 812 raft_layers = 0
 813 resolution = 0
 814 seam_position = aligned
 815 skirt_distance = 1
 816 skirt_height = 1
 817 skirts = 1
 818 small_perimeter_speed = 10
 819 solid_infill_below_area = 70
 820 solid_infill_every_layers = 0
 821 solid_infill_extruder = 1
 822 solid_infill_extrusion_width = 0
 823 solid_infill_speed = 0
 824 spiral_vase = 0
 825 standby_temperature_delta = -5
 826 support_material = 1
 827 support_material_angle = 0
 828 support_material_contact_distance = 0.2
 829 support_material_enforce_layers = 0
 830 support_material_extruder = 1
 831 support_material_extrusion_width = 0
 832 support_material_interface_extruder = 1
 833 support_material_interface_layers = 2
 834 support_material_interface_spacing = 0
 835 support_material_interface_speed = 100%
 836 support_material_pattern = rectilinear
 837 support_material_spacing = 5
 838 support_material_speed = 0
 839 support_material_threshold = 40
 840 thin_walls = 1
 841 threads = 2
 842 top_infill_extrusion_width = 0
 843 top_solid_infill_speed = 20
 844 top_solid_layers = 3
 845 travel_speed = 100
 846 xy_size_compensation = 0
 847
 848 [printer:LULZBOT ABS fine]
 849 bed_shape = 0x0,298x0,298x275,0x275
 850 before_layer_gcode =
 851 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
 852 extruder_offset = 0x0
 853 gcode_flavor = reprap
 854 layer_gcode =
 855 nozzle_diameter = 0.35
 856 octoprint_apikey =
 857 octoprint_host =
 858 pressure_advance = 0
 859 retract_before_travel = 2
 860 retract_layer_change = 1
 861 retract_length = 1.75
 862 retract_length_toolchange = 3
 863 retract_lift = 0
 864 retract_restart_extra = 0
 865 retract_restart_extra_toolchange = 0
 866 retract_speed = 20
 867 start_gcode = G28 ; home all axes
 868 toolchange_gcode =
 869 use_firmware_retraction = 0
 870 use_relative_e_distances = 0
 871 use_volumetric_e = 0
 872 vibration_limit = 0
 873 wipe = 0
 874 z_offset = 0
 875
 876 [printer:MendelPro]
 877 bed_shape = 0x0,220x0,220x177,0x177
 878 before_layer_gcode =
 879 end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nM84               ; disable motors\n
 880 extruder_offset = 0x0
 881 gcode_flavor = reprap
 882 layer_gcode =
 883 nozzle_diameter = 0.5
 884 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
 885 octoprint_host =
 886 pressure_advance = 0
 887 retract_before_travel = 2
 888 retract_layer_change = 1
 889 retract_length = 5
 890 retract_length_toolchange = 10
 891 retract_lift = 0
 892 retract_restart_extra = 0
 893 retract_restart_extra_toolchange = 0
 894 retract_speed = 40
 895 start_gcode = G28 Z            ; home Z\nG28 X Y         ; home X Y\n
 896 toolchange_gcode =
 897 use_firmware_retraction = 0
 898 use_relative_e_distances = 0
 899 use_volumetric_e = 0
 900 vibration_limit = 0
 901 wipe = 0
 902 z_offset = 0
 903
 904 [printer:TinyBoy]
 905 bed_shape = 0x0,88x0,88x74,0x74
 906 before_layer_gcode =
 907 end_gcode = M104 S0        ; turn off temperature\nG28 X0           ; home X axis\nM84               ; disable motors\n
 908 extruder_offset = 0x0
 909 gcode_flavor = reprap
 910 layer_gcode =
 911 nozzle_diameter = 0.4
 912 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
 913 octoprint_host =
 914 pressure_advance = 0
 915 retract_before_travel = 2
 916 retract_layer_change = 1
 917 retract_length = 5
 918 retract_length_toolchange = 10
 919 retract_lift = 0
 920 retract_restart_extra = 0
 921 retract_restart_extra_toolchange = 0
 922 retract_speed = 40
 923 start_gcode = G28 Z            ; home Z\nG0 Z 1          ; lift Z\nG28 X Y         ; home X Y\n
 924 toolchange_gcode =
 925 use_firmware_retraction = 0
 926 use_relative_e_distances = 0
 927 use_volumetric_e = 0
 928 vibration_limit = 0
 929 wipe = 0
 930 z_offset = 0
 931
 932 [printer:prusa i3]
 933 bed_shape = 0x0,190x0,190x190,0x190
 934 before_layer_gcode =
 935 end_gcode = M104 S0        ; turn off temperature\nM140 S0        ; turn off bed temp \nG28 X0           ; home X axis\nG0 Y190         ; präsent object\nM84               ; disable motors\n\n
 936 extruder_offset = 0x0
 937 gcode_flavor = reprap
 938 layer_gcode =
 939 nozzle_diameter = 0.4
 940 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
 941 octoprint_host =
 942 pressure_advance = 0
 943 retract_before_travel = 2
 944 retract_layer_change = 1
 945 retract_length = 5
 946 retract_length_toolchange = 10
 947 retract_lift = 0
 948 retract_restart_extra = 0
 949 retract_restart_extra_toolchange = 0
 950 retract_speed = 40
 951 start_gcode = G28 Z            ; home Z\n\nG28 X Y         ; home X Y\n
 952 toolchange_gcode =
 953 use_firmware_retraction = 0
 954 use_relative_e_distances = 0
 955 use_volumetric_e = 0
 956 vibration_limit = 0
 957 wipe = 0
 958 z_offset = 0
 959
 960 [settings]
 961 autocenter = 1
 962 mode = expert