3D-Drucker%2FSlicerBundle.ini.mw

   1 # generated by Slic3r 1.2.9 on Thu Jun  2 16:16:44 2016
   2
   3 [filament:Lulzbot ABS]
   4 bed_temperature = 100
   5 bridge_fan_speed = 100
   6 cooling = 0
   7 disable_fan_first_layers = 1
   8 extrusion_multiplier = 1
   9 fan_always_on = 0
  10 fan_below_layer_time = 60
  11 filament_colour = #FFFFFF
  12 filament_diameter = 2.85
  13 first_layer_bed_temperature = 100
  14 first_layer_temperature = 250
  15 max_fan_speed = 100
  16 min_fan_speed = 30
  17 min_print_speed = 10
  18 slowdown_below_layer_time = 20
  19 temperature = 245
  20
  21 [filament:Lulzbot PLA]
  22 bed_temperature = 50
  23 bridge_fan_speed = 100
  24 cooling = 1
  25 disable_fan_first_layers = 1
  26 extrusion_multiplier = 1
  27 fan_always_on = 1
  28 fan_below_layer_time = 60
  29 filament_colour = #FFFFFF
  30 filament_diameter = 2.85
  31 first_layer_bed_temperature = 55
  32 first_layer_temperature = 200
  33 max_fan_speed = 100
  34 min_fan_speed = 35
  35 min_print_speed = 10
  36 slowdown_below_layer_time = 30
  37 temperature = 190
  38
  39 [filament:Lulzbot PLA Weiß]
  40 bed_temperature = 50
  41 bridge_fan_speed = 100
  42 cooling = 1
  43 disable_fan_first_layers = 1
  44 extrusion_multiplier = 1
  45 fan_always_on = 0
  46 fan_below_layer_time = 60
  47 filament_colour = #FFFFFF
  48 filament_diameter = 2.85
  49 first_layer_bed_temperature = 55
  50 first_layer_temperature = 200
  51 max_fan_speed = 100
  52 min_fan_speed = 30
  53 min_print_speed = 10
  54 slowdown_below_layer_time = 20
  55 temperature = 190
  56
  57 [filament:MendelPro ABS]
  58 bed_temperature = 0
  59 bridge_fan_speed = 100
  60 cooling = 0
  61 disable_fan_first_layers = 1
  62 extrusion_multiplier = 1
  63 fan_always_on = 0
  64 fan_below_layer_time = 60
  65 filament_colour = #FFFFFF
  66 filament_diameter = 1.7
  67 first_layer_bed_temperature = 0
  68 first_layer_temperature = 250
  69 max_fan_speed = 100
  70 min_fan_speed = 50
  71 min_print_speed = 5
  72 slowdown_below_layer_time = 30
  73 temperature = 245
  74
  75 [filament:MendelPro Holz]
  76 bed_temperature = 50
  77 bridge_fan_speed = 100
  78 cooling = 1
  79 disable_fan_first_layers = 1
  80 extrusion_multiplier = 1
  81 fan_always_on = 1
  82 fan_below_layer_time = 60
  83 filament_colour = #FFFFFF
  84 filament_diameter = 1.7
  85 first_layer_bed_temperature = 55
  86 first_layer_temperature = 200
  87 max_fan_speed = 100
  88 min_fan_speed = 50
  89 min_print_speed = 5
  90 slowdown_below_layer_time = 30
  91 temperature = 185
  92
  93 [filament:MendelPro PLA]
  94 bed_temperature = 50
  95 bridge_fan_speed = 100
  96 cooling = 1
  97 disable_fan_first_layers = 1
  98 extrusion_multiplier = 1
  99 fan_always_on = 1
 100 fan_below_layer_time = 60
 101 filament_colour = #FFFFFF
 102 filament_diameter = 1.7
 103 first_layer_bed_temperature = 55
 104 first_layer_temperature = 200
 105 max_fan_speed = 100
 106 min_fan_speed = 40
 107 min_print_speed = 5
 108 slowdown_below_layer_time = 30
 109 temperature = 180
 110
 111 [filament:MendelPro PLA fast]
 112 bed_temperature = 50
 113 bridge_fan_speed = 100
 114 cooling = 1
 115 disable_fan_first_layers = 1
 116 extrusion_multiplier = 1
 117 fan_always_on = 1
 118 fan_below_layer_time = 60
 119 filament_colour = #FFFFFF
 120 filament_diameter = 1.7
 121 first_layer_bed_temperature = 50
 122 first_layer_temperature = 200
 123 max_fan_speed = 100
 124 min_fan_speed = 50
 125 min_print_speed = 5
 126 slowdown_below_layer_time = 30
 127 temperature = 200
 128
 129 [filament:MendelPro PLA transparent]
 130 bed_temperature = 50
 131 bridge_fan_speed = 100
 132 cooling = 1
 133 disable_fan_first_layers = 1
 134 extrusion_multiplier = 1
 135 fan_always_on = 1
 136 fan_below_layer_time = 60
 137 filament_colour = #FFFFFF
 138 filament_diameter = 1.7
 139 first_layer_bed_temperature = 55
 140 first_layer_temperature = 200
 141 max_fan_speed = 100
 142 min_fan_speed = 40
 143 min_print_speed = 5
 144 slowdown_below_layer_time = 30
 145 temperature = 200
 146
 147 [filament:TinyBoy PLA]
 148 bed_temperature = 0
 149 bridge_fan_speed = 100
 150 cooling = 1
 151 disable_fan_first_layers = 2
 152 extrusion_multiplier = 0.9
 153 fan_always_on = 1
 154 fan_below_layer_time = 60
 155 filament_colour = #35E1FF
 156 filament_diameter = 1.7
 157 first_layer_bed_temperature = 0
 158 first_layer_temperature = 200
 159 max_fan_speed = 50
 160 min_fan_speed = 35
 161 min_print_speed = 5
 162 slowdown_below_layer_time = 15
 163 temperature = 185
 164
 165 [filament:Toy]
 166 bed_temperature = 0
 167 bridge_fan_speed = 100
 168 cooling = 1
 169 disable_fan_first_layers = 1
 170 extrusion_multiplier = 1
 171 fan_always_on = 1
 172 fan_below_layer_time = 60
 173 filament_colour = #FFFFFF
 174 filament_diameter = 1.7
 175 first_layer_bed_temperature = 0
 176 first_layer_temperature = 200
 177 max_fan_speed = 100
 178 min_fan_speed = 100
 179 min_print_speed = 5
 180 slowdown_below_layer_time = 30
 181 temperature = 180
 182
 183 [filament:prusa i3 PLA black fine]
 184 bed_temperature = 50
 185 bridge_fan_speed = 100
 186 cooling = 1
 187 disable_fan_first_layers = 1
 188 extrusion_multiplier = 1
 189 fan_always_on = 1
 190 fan_below_layer_time = 60
 191 filament_colour = #FF0000
 192 filament_diameter = 2.9
 193 first_layer_bed_temperature = 50
 194 first_layer_temperature = 200
 195 max_fan_speed = 100
 196 min_fan_speed = 100
 197 min_print_speed = 5
 198 slowdown_below_layer_time = 15
 199 temperature = 200
 200
 201 [filament:prusa i3 PLA lila]
 202 bed_temperature = 50
 203 bridge_fan_speed = 100
 204 cooling = 1
 205 disable_fan_first_layers = 1
 206 extrusion_multiplier = 1
 207 fan_always_on = 1
 208 fan_below_layer_time = 60
 209 filament_colour = #8000FF
 210 filament_diameter = 3
 211 first_layer_bed_temperature = 50
 212 first_layer_temperature = 200
 213 max_fan_speed = 100
 214 min_fan_speed = 35
 215 min_print_speed = 5
 216 slowdown_below_layer_time = 15
 217 temperature = 200
 218
 219 [presets]
 220 filament = MendelPro PLA fast.ini
 221 print = Lulzbot fine.ini
 222 printer = Lulzbot.ini
 223
 224 [print:Lulzbot fine]
 225 avoid_crossing_perimeters = 1
 226 bottom_solid_layers = 4
 227 bridge_acceleration = 0
 228 bridge_flow_ratio = 1
 229 bridge_speed = 40
 230 brim_width = 0
 231 complete_objects = 0
 232 default_acceleration = 0
 233 dont_support_bridges = 1
 234 external_fill_pattern = rectilinear
 235 external_perimeter_extrusion_width = 0
 236 external_perimeter_speed = 30
 237 external_perimeters_first = 0
 238 extra_perimeters = 1
 239 extruder_clearance_height = 20
 240 extruder_clearance_radius = 20
 241 extrusion_width = 0
 242 fill_angle = 35
 243 fill_density = 30%
 244 fill_pattern = line
 245 first_layer_acceleration = 0
 246 first_layer_extrusion_width = 0
 247 first_layer_height = 0.2
 248 first_layer_speed = 10
 249 gap_fill_speed = 20
 250 gcode_comments = 0
 251 infill_acceleration = 0
 252 infill_every_layers = 2
 253 infill_extruder = 1
 254 infill_extrusion_width = 110%
 255 infill_first = 0
 256 infill_only_where_needed = 0
 257 infill_overlap = 15%
 258 infill_speed = 0
 259 interface_shells = 0
 260 layer_height = 0.25
 261 max_print_speed = 100
 262 max_volumetric_speed = 0
 263 min_skirt_length = 0
 264 notes =
 265 only_retract_when_crossing_perimeters = 0
 266 ooze_prevention = 0
 267 output_filename_format = [input_filename_base].gcode
 268 overhangs = 1
 269 perimeter_acceleration = 0
 270 perimeter_extruder = 1
 271 perimeter_extrusion_width = 0
 272 perimeter_speed = 0
 273 perimeters = 3
 274 post_process =
 275 raft_layers = 0
 276 resolution = 0
 277 seam_position = aligned
 278 skirt_distance = 6
 279 skirt_height = 1
 280 skirts = 2
 281 small_perimeter_speed = 20
 282 solid_infill_below_area = 30
 283 solid_infill_every_layers = 0
 284 solid_infill_extruder = 1
 285 solid_infill_extrusion_width = 0
 286 solid_infill_speed = 0
 287 spiral_vase = 0
 288 standby_temperature_delta = -5
 289 support_material = 0
 290 support_material_angle = 0
 291 support_material_contact_distance = 0.2
 292 support_material_enforce_layers = 0
 293 support_material_extruder = 1
 294 support_material_extrusion_width = 0
 295 support_material_interface_extruder = 1
 296 support_material_interface_layers = 0
 297 support_material_interface_spacing = 0
 298 support_material_interface_speed = 100%
 299 support_material_pattern = rectilinear
 300 support_material_spacing = 2.5
 301 support_material_speed = 0
 302 support_material_threshold = 45
 303 thin_walls = 1
 304 threads = 2
 305 top_infill_extrusion_width = 0
 306 top_solid_infill_speed = 30
 307 top_solid_layers = 4
 308 travel_speed = 100
 309 xy_size_compensation = 0
 310
 311 [print:MendelPro]
 312 avoid_crossing_perimeters = 0
 313 bottom_solid_layers = 3
 314 bridge_acceleration = 0
 315 bridge_flow_ratio = 1
 316 bridge_speed = 40
 317 brim_width = 0
 318 complete_objects = 0
 319 default_acceleration = 0
 320 dont_support_bridges = 1
 321 external_fill_pattern = rectilinear
 322 external_perimeter_extrusion_width = 0
 323 external_perimeter_speed = 20
 324 external_perimeters_first = 0
 325 extra_perimeters = 1
 326 extruder_clearance_height = 20
 327 extruder_clearance_radius = 20
 328 extrusion_width = 0
 329 fill_angle = 45
 330 fill_density = 15%
 331 fill_pattern = rectilinear
 332 first_layer_acceleration = 0
 333 first_layer_extrusion_width = 0
 334 first_layer_height = 0.2
 335 first_layer_speed = 10
 336 gap_fill_speed = 10
 337 gcode_comments = 0
 338 infill_acceleration = 0
 339 infill_every_layers = 1
 340 infill_extruder = 1
 341 infill_extrusion_width = 0
 342 infill_first = 0
 343 infill_only_where_needed = 0
 344 infill_overlap = 15%
 345 infill_speed = 0
 346 interface_shells = 0
 347 layer_height = 0.2
 348 max_print_speed = 80
 349 max_volumetric_speed = 0
 350 min_skirt_length = 2
 351 notes =
 352 only_retract_when_crossing_perimeters = 1
 353 ooze_prevention = 0
 354 output_filename_format = [input_filename_base].gcode
 355 overhangs = 1
 356 perimeter_acceleration = 0
 357 perimeter_extruder = 1
 358 perimeter_extrusion_width = 0
 359 perimeter_speed = 0
 360 perimeters = 2
 361 post_process =
 362 raft_layers = 0
 363 resolution = 0
 364 seam_position = aligned
 365 skirt_distance = 1
 366 skirt_height = 1
 367 skirts = 1
 368 small_perimeter_speed = 10
 369 solid_infill_below_area = 70
 370 solid_infill_every_layers = 0
 371 solid_infill_extruder = 1
 372 solid_infill_extrusion_width = 0
 373 solid_infill_speed = 0
 374 spiral_vase = 0
 375 standby_temperature_delta = -5
 376 support_material = 0
 377 support_material_angle = 0
 378 support_material_contact_distance = 0.2
 379 support_material_enforce_layers = 0
 380 support_material_extruder = 1
 381 support_material_extrusion_width = 0
 382 support_material_interface_extruder = 1
 383 support_material_interface_layers = 2
 384 support_material_interface_spacing = 0
 385 support_material_interface_speed = 100%
 386 support_material_pattern = rectilinear
 387 support_material_spacing = 5
 388 support_material_speed = 0
 389 support_material_threshold = 40
 390 thin_walls = 1
 391 threads = 2
 392 top_infill_extrusion_width = 0
 393 top_solid_infill_speed = 20
 394 top_solid_layers = 3
 395 travel_speed = 100
 396 xy_size_compensation = 0
 397
 398 [print:MendelPro fast]
 399 avoid_crossing_perimeters = 0
 400 bottom_solid_layers = 3
 401 bridge_acceleration = 0
 402 bridge_flow_ratio = 1
 403 bridge_speed = 40
 404 brim_width = 0
 405 complete_objects = 0
 406 default_acceleration = 0
 407 dont_support_bridges = 1
 408 external_fill_pattern = rectilinear
 409 external_perimeter_extrusion_width = 0
 410 external_perimeter_speed = 20
 411 external_perimeters_first = 0
 412 extra_perimeters = 1
 413 extruder_clearance_height = 20
 414 extruder_clearance_radius = 20
 415 extrusion_width = 0
 416 fill_angle = 45
 417 fill_density = 15%
 418 fill_pattern = rectilinear
 419 first_layer_acceleration = 0
 420 first_layer_extrusion_width = 0
 421 first_layer_height = 0.2
 422 first_layer_speed = 10
 423 gap_fill_speed = 10
 424 gcode_comments = 0
 425 infill_acceleration = 0
 426 infill_every_layers = 1
 427 infill_extruder = 1
 428 infill_extrusion_width = 0
 429 infill_first = 0
 430 infill_only_where_needed = 0
 431 infill_overlap = 15%
 432 infill_speed = 0
 433 interface_shells = 0
 434 layer_height = 0.5
 435 max_print_speed = 80
 436 max_volumetric_speed = 0
 437 min_skirt_length = 2
 438 notes =
 439 only_retract_when_crossing_perimeters = 1
 440 ooze_prevention = 0
 441 output_filename_format = [input_filename_base].gcode
 442 overhangs = 1
 443 perimeter_acceleration = 0
 444 perimeter_extruder = 1
 445 perimeter_extrusion_width = 0
 446 perimeter_speed = 0
 447 perimeters = 2
 448 post_process =
 449 raft_layers = 0
 450 resolution = 0
 451 seam_position = aligned
 452 skirt_distance = 1
 453 skirt_height = 1
 454 skirts = 1
 455 small_perimeter_speed = 10
 456 solid_infill_below_area = 70
 457 solid_infill_every_layers = 0
 458 solid_infill_extruder = 1
 459 solid_infill_extrusion_width = 0
 460 solid_infill_speed = 0
 461 spiral_vase = 0
 462 standby_temperature_delta = -5
 463 support_material = 0
 464 support_material_angle = 0
 465 support_material_contact_distance = 0.2
 466 support_material_enforce_layers = 0
 467 support_material_extruder = 1
 468 support_material_extrusion_width = 0
 469 support_material_interface_extruder = 1
 470 support_material_interface_layers = 2
 471 support_material_interface_spacing = 0
 472 support_material_interface_speed = 100%
 473 support_material_pattern = rectilinear
 474 support_material_spacing = 5
 475 support_material_speed = 0
 476 support_material_threshold = 40
 477 thin_walls = 1
 478 threads = 2
 479 top_infill_extrusion_width = 0
 480 top_solid_infill_speed = 20
 481 top_solid_layers = 3
 482 travel_speed = 100
 483 xy_size_compensation = 0
 484
 485 [print:TinyBoy]
 486 avoid_crossing_perimeters = 0
 487 bottom_solid_layers = 3
 488 bridge_acceleration = 0
 489 bridge_flow_ratio = 1
 490 bridge_speed = 0
 491 brim_width = 0
 492 complete_objects = 0
 493 default_acceleration = 0
 494 dont_support_bridges = 1
 495 external_fill_pattern = rectilinear
 496 external_perimeter_extrusion_width = 0
 497 external_perimeter_speed = 0
 498 external_perimeters_first = 0
 499 extra_perimeters = 1
 500 extruder_clearance_height = 20
 501 extruder_clearance_radius = 20
 502 extrusion_width = 0
 503 fill_angle = 45
 504 fill_density = 15%
 505 fill_pattern = rectilinear
 506 first_layer_acceleration = 0
 507 first_layer_extrusion_width = 150%
 508 first_layer_height = 0.2
 509 first_layer_speed = 20
 510 gap_fill_speed = 0
 511 gcode_comments = 0
 512 infill_acceleration = 0
 513 infill_every_layers = 1
 514 infill_extruder = 1
 515 infill_extrusion_width = 0
 516 infill_first = 0
 517 infill_only_where_needed = 0
 518 infill_overlap = 15%
 519 infill_speed = 0
 520 interface_shells = 0
 521 layer_height = 0.2
 522 max_print_speed = 50
 523 max_volumetric_speed = 0
 524 min_skirt_length = 1
 525 notes =
 526 only_retract_when_crossing_perimeters = 1
 527 ooze_prevention = 0
 528 output_filename_format = [input_filename_base].gcode
 529 overhangs = 1
 530 perimeter_acceleration = 0
 531 perimeter_extruder = 1
 532 perimeter_extrusion_width = 0
 533 perimeter_speed = 0
 534 perimeters = 2
 535 post_process =
 536 raft_layers = 0
 537 resolution = 0
 538 seam_position = aligned
 539 skirt_distance = 1
 540 skirt_height = 1
 541 skirts = 1
 542 small_perimeter_speed = 0
 543 solid_infill_below_area = 70
 544 solid_infill_every_layers = 0
 545 solid_infill_extruder = 1
 546 solid_infill_extrusion_width = 0
 547 solid_infill_speed = 0
 548 spiral_vase = 0
 549 standby_temperature_delta = -5
 550 support_material = 0
 551 support_material_angle = 0
 552 support_material_contact_distance = 0.2
 553 support_material_enforce_layers = 0
 554 support_material_extruder = 1
 555 support_material_extrusion_width = 0
 556 support_material_interface_extruder = 1
 557 support_material_interface_layers = 2
 558 support_material_interface_spacing = 0
 559 support_material_interface_speed = 100%
 560 support_material_pattern = rectilinear
 561 support_material_spacing = 5
 562 support_material_speed = 0
 563 support_material_threshold = 40
 564 thin_walls = 1
 565 threads = 2
 566 top_infill_extrusion_width = 0
 567 top_solid_infill_speed = 0
 568 top_solid_layers = 3
 569 travel_speed = 100
 570 xy_size_compensation = 0
 571
 572 [print:Toy]
 573 avoid_crossing_perimeters = 0
 574 bottom_solid_layers = 2
 575 bridge_acceleration = 0
 576 bridge_flow_ratio = 1
 577 bridge_speed = 0
 578 brim_width = 0
 579 complete_objects = 0
 580 default_acceleration = 0
 581 dont_support_bridges = 1
 582 external_fill_pattern = rectilinear
 583 external_perimeter_extrusion_width = 0
 584 external_perimeter_speed = 0
 585 external_perimeters_first = 0
 586 extra_perimeters = 1
 587 extruder_clearance_height = 20
 588 extruder_clearance_radius = 20
 589 extrusion_width = 0
 590 fill_angle = 45
 591 fill_density = 0%
 592 fill_pattern = rectilinear
 593 first_layer_acceleration = 0
 594 first_layer_extrusion_width = 0
 595 first_layer_height = 0.2
 596 first_layer_speed = 10
 597 gap_fill_speed = 0
 598 gcode_comments = 0
 599 infill_acceleration = 0
 600 infill_every_layers = 1
 601 infill_extruder = 1
 602 infill_extrusion_width = 0
 603 infill_first = 0
 604 infill_only_where_needed = 0
 605 infill_overlap = 15%
 606 infill_speed = 0
 607 interface_shells = 0
 608 layer_height = 0.2
 609 max_print_speed = 10
 610 max_volumetric_speed = 0
 611 min_skirt_length = 1
 612 notes =
 613 only_retract_when_crossing_perimeters = 1
 614 ooze_prevention = 0
 615 output_filename_format = [input_filename_base].gcode
 616 overhangs = 1
 617 perimeter_acceleration = 0
 618 perimeter_extruder = 1
 619 perimeter_extrusion_width = 0
 620 perimeter_speed = 0
 621 perimeters = 2
 622 post_process =
 623 raft_layers = 0
 624 resolution = 0
 625 seam_position = aligned
 626 skirt_distance = 1
 627 skirt_height = 1
 628 skirts = 1
 629 small_perimeter_speed = 0
 630 solid_infill_below_area = 70
 631 solid_infill_every_layers = 0
 632 solid_infill_extruder = 1
 633 solid_infill_extrusion_width = 0
 634 solid_infill_speed = 0
 635 spiral_vase = 0
 636 standby_temperature_delta = -5
 637 support_material = 0
 638 support_material_angle = 0
 639 support_material_contact_distance = 0.2
 640 support_material_enforce_layers = 0
 641 support_material_extruder = 1
 642 support_material_extrusion_width = 0
 643 support_material_interface_extruder = 1
 644 support_material_interface_layers = 2
 645 support_material_interface_spacing = 0
 646 support_material_interface_speed = 100%
 647 support_material_pattern = rectilinear
 648 support_material_spacing = 5
 649 support_material_speed = 0
 650 support_material_threshold = 40
 651 thin_walls = 1
 652 threads = 2
 653 top_infill_extrusion_width = 0
 654 top_solid_infill_speed = 0
 655 top_solid_layers = 0
 656 travel_speed = 100
 657 xy_size_compensation = 0
 658
 659 [print:prusa i3 100]
 660 avoid_crossing_perimeters = 0
 661 bottom_solid_layers = 3
 662 bridge_acceleration = 0
 663 bridge_flow_ratio = 1
 664 bridge_speed = 40
 665 brim_width = 0
 666 complete_objects = 0
 667 default_acceleration = 0
 668 dont_support_bridges = 1
 669 external_fill_pattern = rectilinear
 670 external_perimeter_extrusion_width = 0
 671 external_perimeter_speed = 10
 672 external_perimeters_first = 0
 673 extra_perimeters = 1
 674 extruder_clearance_height = 20
 675 extruder_clearance_radius = 20
 676 extrusion_width = 0
 677 fill_angle = 45
 678 fill_density = 20%
 679 fill_pattern = rectilinear
 680 first_layer_acceleration = 0
 681 first_layer_extrusion_width = 0
 682 first_layer_height = 0.2
 683 first_layer_speed = 10
 684 gap_fill_speed = 10
 685 gcode_comments = 0
 686 infill_acceleration = 0
 687 infill_every_layers = 1
 688 infill_extruder = 1
 689 infill_extrusion_width = 110%
 690 infill_first = 0
 691 infill_only_where_needed = 0
 692 infill_overlap = 15%
 693 infill_speed = 0
 694 interface_shells = 0
 695 layer_height = 0.1
 696 max_print_speed = 80
 697 max_volumetric_speed = 0
 698 min_skirt_length = 1
 699 notes =
 700 only_retract_when_crossing_perimeters = 1
 701 ooze_prevention = 0
 702 output_filename_format = [input_filename_base].gcode
 703 overhangs = 1
 704 perimeter_acceleration = 0
 705 perimeter_extruder = 1
 706 perimeter_extrusion_width = 0
 707 perimeter_speed = 0
 708 perimeters = 3
 709 post_process =
 710 raft_layers = 0
 711 resolution = 0
 712 seam_position = aligned
 713 skirt_distance = 6
 714 skirt_height = 1
 715 skirts = 3
 716 small_perimeter_speed = 10
 717 solid_infill_below_area = 70
 718 solid_infill_every_layers = 0
 719 solid_infill_extruder = 1
 720 solid_infill_extrusion_width = 0
 721 solid_infill_speed = 0
 722 spiral_vase = 0
 723 standby_temperature_delta = -5
 724 support_material = 0
 725 support_material_angle = 0
 726 support_material_contact_distance = 0.2
 727 support_material_enforce_layers = 0
 728 support_material_extruder = 1
 729 support_material_extrusion_width = 0
 730 support_material_interface_extruder = 1
 731 support_material_interface_layers = 2
 732 support_material_interface_spacing = 0
 733 support_material_interface_speed = 100%
 734 support_material_pattern = rectilinear
 735 support_material_spacing = 5
 736 support_material_speed = 0
 737 support_material_threshold = 40
 738 thin_walls = 1
 739 threads = 2
 740 top_infill_extrusion_width = 0
 741 top_solid_infill_speed = 10
 742 top_solid_layers = 3
 743 travel_speed = 100
 744 xy_size_compensation = 0
 745
 746 [print:prusa i3 250]
 747 avoid_crossing_perimeters = 0
 748 bottom_solid_layers = 3
 749 bridge_acceleration = 0
 750 bridge_flow_ratio = 1
 751 bridge_speed = 40
 752 brim_width = 0
 753 complete_objects = 0
 754 default_acceleration = 0
 755 dont_support_bridges = 1
 756 external_fill_pattern = rectilinear
 757 external_perimeter_extrusion_width = 0
 758 external_perimeter_speed = 10
 759 external_perimeters_first = 0
 760 extra_perimeters = 1
 761 extruder_clearance_height = 20
 762 extruder_clearance_radius = 20
 763 extrusion_width = 0
 764 fill_angle = 45
 765 fill_density = 20%
 766 fill_pattern = rectilinear
 767 first_layer_acceleration = 0
 768 first_layer_extrusion_width = 0
 769 first_layer_height = 0.2
 770 first_layer_speed = 15
 771 gap_fill_speed = 10
 772 gcode_comments = 0
 773 infill_acceleration = 0
 774 infill_every_layers = 1
 775 infill_extruder = 1
 776 infill_extrusion_width = 110%
 777 infill_first = 0
 778 infill_only_where_needed = 0
 779 infill_overlap = 15%
 780 infill_speed = 0
 781 interface_shells = 0
 782 layer_height = 0.25
 783 max_print_speed = 60
 784 max_volumetric_speed = 0
 785 min_skirt_length = 1
 786 notes =
 787 only_retract_when_crossing_perimeters = 1
 788 ooze_prevention = 0
 789 output_filename_format = [input_filename_base].gcode
 790 overhangs = 1
 791 perimeter_acceleration = 0
 792 perimeter_extruder = 1
 793 perimeter_extrusion_width = 0
 794 perimeter_speed = 0
 795 perimeters = 2
 796 post_process =
 797 raft_layers = 0
 798 resolution = 0
 799 seam_position = aligned
 800 skirt_distance = 1
 801 skirt_height = 1
 802 skirts = 1
 803 small_perimeter_speed = 10
 804 solid_infill_below_area = 70
 805 solid_infill_every_layers = 0
 806 solid_infill_extruder = 1
 807 solid_infill_extrusion_width = 0
 808 solid_infill_speed = 0
 809 spiral_vase = 0
 810 standby_temperature_delta = -5
 811 support_material = 0
 812 support_material_angle = 0
 813 support_material_contact_distance = 0.2
 814 support_material_enforce_layers = 0
 815 support_material_extruder = 1
 816 support_material_extrusion_width = 0
 817 support_material_interface_extruder = 1
 818 support_material_interface_layers = 2
 819 support_material_interface_spacing = 0
 820 support_material_interface_speed = 100%
 821 support_material_pattern = rectilinear
 822 support_material_spacing = 5
 823 support_material_speed = 0
 824 support_material_threshold = 40
 825 thin_walls = 1
 826 threads = 2
 827 top_infill_extrusion_width = 0
 828 top_solid_infill_speed = 20
 829 top_solid_layers = 3
 830 travel_speed = 100
 831 xy_size_compensation = 0
 832
 833 [print:prusa i3 400]
 834 avoid_crossing_perimeters = 0
 835 bottom_solid_layers = 3
 836 bridge_acceleration = 0
 837 bridge_flow_ratio = 1
 838 bridge_speed = 60
 839 brim_width = 0
 840 complete_objects = 0
 841 default_acceleration = 0
 842 dont_support_bridges = 1
 843 external_fill_pattern = rectilinear
 844 external_perimeter_extrusion_width = 0
 845 external_perimeter_speed = 20
 846 external_perimeters_first = 0
 847 extra_perimeters = 1
 848 extruder_clearance_height = 20
 849 extruder_clearance_radius = 20
 850 extrusion_width = 0
 851 fill_angle = 45
 852 fill_density = 20%
 853 fill_pattern = rectilinear
 854 first_layer_acceleration = 0
 855 first_layer_extrusion_width = 0
 856 first_layer_height = 0.2
 857 first_layer_speed = 10
 858 gap_fill_speed = 10
 859 gcode_comments = 0
 860 infill_acceleration = 0
 861 infill_every_layers = 1
 862 infill_extruder = 1
 863 infill_extrusion_width = 110%
 864 infill_first = 0
 865 infill_only_where_needed = 0
 866 infill_overlap = 15%
 867 infill_speed = 0
 868 interface_shells = 0
 869 layer_height = 0.4
 870 max_print_speed = 80
 871 max_volumetric_speed = 0
 872 min_skirt_length = 1
 873 notes =
 874 only_retract_when_crossing_perimeters = 1
 875 ooze_prevention = 0
 876 output_filename_format = [input_filename_base].gcode
 877 overhangs = 1
 878 perimeter_acceleration = 0
 879 perimeter_extruder = 1
 880 perimeter_extrusion_width = 0
 881 perimeter_speed = 0
 882 perimeters = 2
 883 post_process =
 884 raft_layers = 0
 885 resolution = 0
 886 seam_position = aligned
 887 skirt_distance = 1
 888 skirt_height = 1
 889 skirts = 1
 890 small_perimeter_speed = 10
 891 solid_infill_below_area = 70
 892 solid_infill_every_layers = 0
 893 solid_infill_extruder = 1
 894 solid_infill_extrusion_width = 0
 895 solid_infill_speed = 0
 896 spiral_vase = 0
 897 standby_temperature_delta = -5
 898 support_material = 0
 899 support_material_angle = 0
 900 support_material_contact_distance = 0.2
 901 support_material_enforce_layers = 0
 902 support_material_extruder = 1
 903 support_material_extrusion_width = 0
 904 support_material_interface_extruder = 1
 905 support_material_interface_layers = 2
 906 support_material_interface_spacing = 0
 907 support_material_interface_speed = 100%
 908 support_material_pattern = rectilinear
 909 support_material_spacing = 5
 910 support_material_speed = 0
 911 support_material_threshold = 40
 912 thin_walls = 1
 913 threads = 2
 914 top_infill_extrusion_width = 0
 915 top_solid_infill_speed = 20
 916 top_solid_layers = 3
 917 travel_speed = 100
 918 xy_size_compensation = 0
 919
 920 [print:prusa i3 400 sup]
 921 avoid_crossing_perimeters = 0
 922 bottom_solid_layers = 3
 923 bridge_acceleration = 0
 924 bridge_flow_ratio = 1
 925 bridge_speed = 60
 926 brim_width = 0
 927 complete_objects = 0
 928 default_acceleration = 0
 929 dont_support_bridges = 1
 930 external_fill_pattern = rectilinear
 931 external_perimeter_extrusion_width = 0
 932 external_perimeter_speed = 20
 933 external_perimeters_first = 0
 934 extra_perimeters = 1
 935 extruder_clearance_height = 20
 936 extruder_clearance_radius = 20
 937 extrusion_width = 0
 938 fill_angle = 45
 939 fill_density = 20%
 940 fill_pattern = rectilinear
 941 first_layer_acceleration = 0
 942 first_layer_extrusion_width = 0
 943 first_layer_height = 0.2
 944 first_layer_speed = 10
 945 gap_fill_speed = 10
 946 gcode_comments = 0
 947 infill_acceleration = 0
 948 infill_every_layers = 1
 949 infill_extruder = 1
 950 infill_extrusion_width = 0
 951 infill_first = 0
 952 infill_only_where_needed = 0
 953 infill_overlap = 15%
 954 infill_speed = 0
 955 interface_shells = 0
 956 layer_height = 0.4
 957 max_print_speed = 80
 958 max_volumetric_speed = 0
 959 min_skirt_length = 1
 960 notes =
 961 only_retract_when_crossing_perimeters = 1
 962 ooze_prevention = 0
 963 output_filename_format = [input_filename_base].gcode
 964 overhangs = 1
 965 perimeter_acceleration = 0
 966 perimeter_extruder = 1
 967 perimeter_extrusion_width = 0
 968 perimeter_speed = 0
 969 perimeters = 2
 970 post_process =
 971 raft_layers = 0
 972 resolution = 0
 973 seam_position = aligned
 974 skirt_distance = 1
 975 skirt_height = 1
 976 skirts = 1
 977 small_perimeter_speed = 10
 978 solid_infill_below_area = 70
 979 solid_infill_every_layers = 0
 980 solid_infill_extruder = 1
 981 solid_infill_extrusion_width = 0
 982 solid_infill_speed = 0
 983 spiral_vase = 0
 984 standby_temperature_delta = -5
 985 support_material = 1
 986 support_material_angle = 0
 987 support_material_contact_distance = 0.3
 988 support_material_enforce_layers = 0
 989 support_material_extruder = 1
 990 support_material_extrusion_width = 90%
 991 support_material_interface_extruder = 1
 992 support_material_interface_layers = 2
 993 support_material_interface_spacing = 2
 994 support_material_interface_speed = 100%
 995 support_material_pattern = rectilinear
 996 support_material_spacing = 5
 997 support_material_speed = 0
 998 support_material_threshold = 40
 999 thin_walls = 1
1000 threads = 2
1001 top_infill_extrusion_width = 0
1002 top_solid_infill_speed = 20
1003 top_solid_layers = 3
1004 travel_speed = 100
1005 xy_size_compensation = 0
1006
1007 [printer:Lulzbot]
1008 bed_shape = 0x0,298x0,298x275,0x275
1009 before_layer_gcode =
1010 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
1011 extruder_offset = 0x0
1012 gcode_flavor = reprap
1013 layer_gcode =
1014 nozzle_diameter = 0.35
1015 octoprint_apikey =
1016 octoprint_host =
1017 pressure_advance = 0
1018 retract_before_travel = 2
1019 retract_layer_change = 1
1020 retract_length = 1.75
1021 retract_length_toolchange = 3
1022 retract_lift = 0
1023 retract_restart_extra = 0
1024 retract_restart_extra_toolchange = 0
1025 retract_speed = 20
1026 start_gcode = G28 ; home all axes\n
1027 toolchange_gcode =
1028 use_firmware_retraction = 0
1029 use_relative_e_distances = 0
1030 use_volumetric_e = 0
1031 vibration_limit = 0
1032 wipe = 0
1033 z_offset = 0
1034
1035 [printer:MendelPro]
1036 bed_shape = 0x0,220x0,220x177,0x177
1037 before_layer_gcode =
1038 end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nG0 Y177;\nM84               ; disable motors\n
1039 extruder_offset = 0x0
1040 gcode_flavor = reprap
1041 layer_gcode =
1042 nozzle_diameter = 0.5
1043 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
1044 octoprint_host =
1045 pressure_advance = 0
1046 retract_before_travel = 2
1047 retract_layer_change = 1
1048 retract_length = 5
1049 retract_length_toolchange = 10
1050 retract_lift = 0
1051 retract_restart_extra = 0
1052 retract_restart_extra_toolchange = 0
1053 retract_speed = 40
1054 start_gcode = G28 Z            ; home Z\nG28 X Y         ; home X Y\n
1055 toolchange_gcode =
1056 use_firmware_retraction = 0
1057 use_relative_e_distances = 0
1058 use_volumetric_e = 0
1059 vibration_limit = 0
1060 wipe = 0
1061 z_offset = 0
1062
1063 [printer:TinyBoy]
1064 bed_shape = 0x0,88x0,88x74,0x74
1065 before_layer_gcode =
1066 end_gcode = M104 S0        ; turn off temperature\nG28 X0           ; home X axis\nM84               ; disable motors\n
1067 extruder_offset = 0x0
1068 gcode_flavor = reprap
1069 layer_gcode =
1070 nozzle_diameter = 0.4
1071 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
1072 octoprint_host =
1073 pressure_advance = 0
1074 retract_before_travel = 2
1075 retract_layer_change = 1
1076 retract_length = 5
1077 retract_length_toolchange = 10
1078 retract_lift = 0
1079 retract_restart_extra = 0
1080 retract_restart_extra_toolchange = 0
1081 retract_speed = 40
1082 start_gcode = G28 Z            ; home Z\nG0 Z 1          ; lift Z\nG28 X Y         ; home X Y\n
1083 toolchange_gcode =
1084 use_firmware_retraction = 0
1085 use_relative_e_distances = 0
1086 use_volumetric_e = 0
1087 vibration_limit = 0
1088 wipe = 0
1089 z_offset = 0
1090
1091 [printer:Toyrep]
1092 bed_shape = 0x0,125x0,125x125,0x125
1093 before_layer_gcode =
1094 end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors
1095 extruder_offset = 0x0
1096 gcode_flavor = reprap
1097 layer_gcode =
1098 nozzle_diameter = 0.4
1099 octoprint_apikey =
1100 octoprint_host =
1101 pressure_advance = 0
1102 retract_before_travel = 2
1103 retract_layer_change = 1
1104 retract_length = 0
1105 retract_length_toolchange = 3
1106 retract_lift = 0
1107 retract_restart_extra = 0
1108 retract_restart_extra_toolchange = 0
1109 retract_speed = 10
1110 start_gcode = \n
1111 toolchange_gcode =
1112 use_firmware_retraction = 0
1113 use_relative_e_distances = 0
1114 use_volumetric_e = 0
1115 vibration_limit = 0
1116 wipe = 0
1117 z_offset = 0
1118
1119 [printer:prusa i3]
1120 bed_shape = 0x0,190x0,190x190,0x190
1121 before_layer_gcode =
1122 end_gcode = M104 S0        ; turn off temperature\nM140 S0        ; turn off bed temp \nG28 X0           ; home X axis\nG0 Y190         ; präsent object\nM84               ; disable motors\n\n
1123 extruder_offset = 0x0
1124 gcode_flavor = reprap
1125 layer_gcode =
1126 nozzle_diameter = 0.4
1127 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
1128 octoprint_host =
1129 pressure_advance = 0
1130 retract_before_travel = 2
1131 retract_layer_change = 1
1132 retract_length = 5
1133 retract_length_toolchange = 10
1134 retract_lift = 0
1135 retract_restart_extra = 0
1136 retract_restart_extra_toolchange = 0
1137 retract_speed = 40
1138 start_gcode = G28 Z            ; home Z\n\nG28 X Y         ; home X Y\n
1139 toolchange_gcode =
1140 use_firmware_retraction = 0
1141 use_relative_e_distances = 0
1142 use_volumetric_e = 0
1143 vibration_limit = 0
1144 wipe = 0
1145 z_offset = 0
1146
1147 [settings]
1148 autocenter = 1
1149 mode = expert