3D-Drucker%2FSlicerBundle.ini.mw

   1 # generated by Slic3r 1.2.9 on Sun Aug 14 14:31:08 2016
   2
   3 [filament:Lulzbot ABS]
   4 bed_temperature = 100
   5 bridge_fan_speed = 50
   6 cooling = 1
   7 disable_fan_first_layers = 1
   8 extrusion_multiplier = 1
   9 fan_always_on = 0
  10 fan_below_layer_time = 60
  11 filament_colour = #FFFFFF
  12 filament_diameter = 2.85
  13 first_layer_bed_temperature = 100
  14 first_layer_temperature = 250
  15 max_fan_speed = 0
  16 min_fan_speed = 0
  17 min_print_speed = 5
  18 slowdown_below_layer_time = 20
  19 temperature = 230
  20
  21 [filament:Lulzbot PLA]
  22 bed_temperature = 50
  23 bridge_fan_speed = 100
  24 cooling = 1
  25 disable_fan_first_layers = 1
  26 extrusion_multiplier = 1
  27 fan_always_on = 1
  28 fan_below_layer_time = 60
  29 filament_colour = #FFFFFF
  30 filament_diameter = 2.82
  31 first_layer_bed_temperature = 50
  32 first_layer_temperature = 200
  33 max_fan_speed = 100
  34 min_fan_speed = 35
  35 min_print_speed = 5
  36 slowdown_below_layer_time = 30
  37 temperature = 200
  38
  39 [filament:Lulzbot PLA Weiß]
  40 bed_temperature = 50
  41 bridge_fan_speed = 100
  42 cooling = 1
  43 disable_fan_first_layers = 1
  44 extrusion_multiplier = 1
  45 fan_always_on = 0
  46 fan_below_layer_time = 60
  47 filament_colour = #FFFFFF
  48 filament_diameter = 2.85
  49 first_layer_bed_temperature = 50
  50 first_layer_temperature = 200
  51 max_fan_speed = 100
  52 min_fan_speed = 30
  53 min_print_speed = 5
  54 slowdown_below_layer_time = 30
  55 temperature = 180
  56
  57 [filament:Lulzbot PLA black]
  58 bed_temperature = 50
  59 bridge_fan_speed = 100
  60 cooling = 1
  61 disable_fan_first_layers = 1
  62 extrusion_multiplier = 1
  63 fan_always_on = 1
  64 fan_below_layer_time = 60
  65 filament_colour = #000000
  66 filament_diameter = 2.9
  67 first_layer_bed_temperature = 50
  68 first_layer_temperature = 200
  69 max_fan_speed = 100
  70 min_fan_speed = 35
  71 min_print_speed = 5
  72 slowdown_below_layer_time = 30
  73 temperature = 200
  74
  75 [filament:MendelPro ABS]
  76 bed_temperature = 0
  77 bridge_fan_speed = 100
  78 cooling = 0
  79 disable_fan_first_layers = 1
  80 extrusion_multiplier = 1
  81 fan_always_on = 0
  82 fan_below_layer_time = 60
  83 filament_colour = #FFFFFF
  84 filament_diameter = 1.7
  85 first_layer_bed_temperature = 0
  86 first_layer_temperature = 250
  87 max_fan_speed = 100
  88 min_fan_speed = 50
  89 min_print_speed = 5
  90 slowdown_below_layer_time = 30
  91 temperature = 245
  92
  93 [filament:MendelPro Holz]
  94 bed_temperature = 50
  95 bridge_fan_speed = 100
  96 cooling = 1
  97 disable_fan_first_layers = 1
  98 extrusion_multiplier = 1
  99 fan_always_on = 1
 100 fan_below_layer_time = 60
 101 filament_colour = #FFFFFF
 102 filament_diameter = 1.7
 103 first_layer_bed_temperature = 55
 104 first_layer_temperature = 200
 105 max_fan_speed = 100
 106 min_fan_speed = 50
 107 min_print_speed = 5
 108 slowdown_below_layer_time = 30
 109 temperature = 185
 110
 111 [filament:MendelPro Mistery]
 112 bed_temperature = 80
 113 bridge_fan_speed = 50
 114 cooling = 1
 115 disable_fan_first_layers = 1
 116 extrusion_multiplier = 1
 117 fan_always_on = 0
 118 fan_below_layer_time = 60
 119 filament_colour = #FFFFFF
 120 filament_diameter = 1.7
 121 first_layer_bed_temperature = 80
 122 first_layer_temperature = 250
 123 max_fan_speed = 0
 124 min_fan_speed = 0
 125 min_print_speed = 10
 126 slowdown_below_layer_time = 20
 127 temperature = 200
 128
 129 [filament:MendelPro PLA]
 130 bed_temperature = 50
 131 bridge_fan_speed = 100
 132 cooling = 1
 133 disable_fan_first_layers = 1
 134 extrusion_multiplier = 1
 135 fan_always_on = 1
 136 fan_below_layer_time = 60
 137 filament_colour = #FFFFFF
 138 filament_diameter = 1.7
 139 first_layer_bed_temperature = 55
 140 first_layer_temperature = 200
 141 max_fan_speed = 100
 142 min_fan_speed = 40
 143 min_print_speed = 5
 144 slowdown_below_layer_time = 30
 145 temperature = 185
 146
 147 [filament:MendelPro PLA fast]
 148 bed_temperature = 50
 149 bridge_fan_speed = 100
 150 cooling = 1
 151 disable_fan_first_layers = 1
 152 extrusion_multiplier = 1
 153 fan_always_on = 1
 154 fan_below_layer_time = 60
 155 filament_colour = #FFFFFF
 156 filament_diameter = 1.7
 157 first_layer_bed_temperature = 50
 158 first_layer_temperature = 200
 159 max_fan_speed = 100
 160 min_fan_speed = 50
 161 min_print_speed = 5
 162 slowdown_below_layer_time = 30
 163 temperature = 200
 164
 165 [filament:MendelPro PLA transparent]
 166 bed_temperature = 50
 167 bridge_fan_speed = 100
 168 cooling = 1
 169 disable_fan_first_layers = 1
 170 extrusion_multiplier = 1
 171 fan_always_on = 1
 172 fan_below_layer_time = 60
 173 filament_colour = #FFFFFF
 174 filament_diameter = 1.7
 175 first_layer_bed_temperature = 55
 176 first_layer_temperature = 200
 177 max_fan_speed = 100
 178 min_fan_speed = 40
 179 min_print_speed = 5
 180 slowdown_below_layer_time = 30
 181 temperature = 200
 182
 183 [filament:TinyBoy PLA]
 184 bed_temperature = 0
 185 bridge_fan_speed = 100
 186 cooling = 1
 187 disable_fan_first_layers = 2
 188 extrusion_multiplier = 0.9
 189 fan_always_on = 1
 190 fan_below_layer_time = 60
 191 filament_colour = #35E1FF
 192 filament_diameter = 1.63
 193 first_layer_bed_temperature = 0
 194 first_layer_temperature = 200
 195 max_fan_speed = 40
 196 min_fan_speed = 35
 197 min_print_speed = 5
 198 slowdown_below_layer_time = 15
 199 temperature = 190
 200
 201 [filament:prusa i3 ABS grün]
 202 bed_temperature = 100
 203 bridge_fan_speed = 70
 204 cooling = 1
 205 disable_fan_first_layers = 1
 206 extrusion_multiplier = 1
 207 fan_always_on = 0
 208 fan_below_layer_time = 60
 209 filament_colour = #80FF00
 210 filament_diameter = 2.9
 211 first_layer_bed_temperature = 100
 212 first_layer_temperature = 255
 213 max_fan_speed = 0
 214 min_fan_speed = 0
 215 min_print_speed = 5
 216 slowdown_below_layer_time = 15
 217 temperature = 245
 218
 219 [filament:prusa i3 ABS grün blau]
 220 bed_temperature = 100
 221 bridge_fan_speed = 70
 222 cooling = 1
 223 disable_fan_first_layers = 1
 224 extrusion_multiplier = 1
 225 fan_always_on = 0
 226 fan_below_layer_time = 60
 227 filament_colour = #0000A0
 228 filament_diameter = 2.9
 229 first_layer_bed_temperature = 100
 230 first_layer_temperature = 240
 231 max_fan_speed = 0
 232 min_fan_speed = 0
 233 min_print_speed = 5
 234 slowdown_below_layer_time = 30
 235 temperature = 235
 236
 237 [filament:prusa i3 ABS schwarz]
 238 bed_temperature = 100
 239 bridge_fan_speed = 70
 240 cooling = 1
 241 disable_fan_first_layers = 1
 242 extrusion_multiplier = 1
 243 fan_always_on = 0
 244 fan_below_layer_time = 60
 245 filament_colour = #000000
 246 filament_diameter = 2.9
 247 first_layer_bed_temperature = 100
 248 first_layer_temperature = 260
 249 max_fan_speed = 0
 250 min_fan_speed = 0
 251 min_print_speed = 5
 252 slowdown_below_layer_time = 15
 253 temperature = 255
 254
 255 [filament:prusa i3 PLA]
 256 bed_temperature = 50
 257 bridge_fan_speed = 100
 258 cooling = 1
 259 disable_fan_first_layers = 1
 260 extrusion_multiplier = 1
 261 fan_always_on = 1
 262 fan_below_layer_time = 60
 263 filament_colour = #FFFFFF
 264 filament_diameter = 2.9
 265 first_layer_bed_temperature = 50
 266 first_layer_temperature = 200
 267 max_fan_speed = 100
 268 min_fan_speed = 50
 269 min_print_speed = 5
 270 slowdown_below_layer_time = 30
 271 temperature = 190
 272
 273 [filament:prusa i3 PLA lila]
 274 bed_temperature = 50
 275 bridge_fan_speed = 100
 276 cooling = 1
 277 disable_fan_first_layers = 1
 278 extrusion_multiplier = 1
 279 fan_always_on = 1
 280 fan_below_layer_time = 60
 281 filament_colour = #8000FF
 282 filament_diameter = 3
 283 first_layer_bed_temperature = 50
 284 first_layer_temperature = 200
 285 max_fan_speed = 100
 286 min_fan_speed = 35
 287 min_print_speed = 5
 288 slowdown_below_layer_time = 15
 289 temperature = 200
 290
 291 [filament:prusa i3 PLA pink]
 292 bed_temperature = 50
 293 bridge_fan_speed = 100
 294 cooling = 1
 295 disable_fan_first_layers = 1
 296 extrusion_multiplier = 1
 297 fan_always_on = 1
 298 fan_below_layer_time = 60
 299 filament_colour = #FF00FF
 300 filament_diameter = 2.83
 301 first_layer_bed_temperature = 50
 302 first_layer_temperature = 200
 303 max_fan_speed = 100
 304 min_fan_speed = 35
 305 min_print_speed = 5
 306 slowdown_below_layer_time = 15
 307 temperature = 180
 308
 309 [presets]
 310 filament = prusa i3 ABS grün blau.ini
 311 print = Lulzbot fine sup.ini
 312 printer = Lulzbot.ini
 313
 314 [print:Lulzbot fine]
 315 avoid_crossing_perimeters = 1
 316 bottom_solid_layers = 2
 317 bridge_acceleration = 0
 318 bridge_flow_ratio = 1
 319 bridge_speed = 40
 320 brim_width = 5
 321 complete_objects = 0
 322 default_acceleration = 0
 323 dont_support_bridges = 1
 324 external_fill_pattern = rectilinear
 325 external_perimeter_extrusion_width = 0
 326 external_perimeter_speed = 50%
 327 external_perimeters_first = 0
 328 extra_perimeters = 1
 329 extruder_clearance_height = 20
 330 extruder_clearance_radius = 20
 331 extrusion_width = 0
 332 fill_angle = 35
 333 fill_density = 15%
 334 fill_pattern = 3dhoneycomb
 335 first_layer_acceleration = 0
 336 first_layer_extrusion_width = 0
 337 first_layer_height = 0.2
 338 first_layer_speed = 10
 339 gap_fill_speed = 20
 340 gcode_comments = 0
 341 infill_acceleration = 0
 342 infill_every_layers = 1
 343 infill_extruder = 1
 344 infill_extrusion_width = 110%
 345 infill_first = 0
 346 infill_only_where_needed = 0
 347 infill_overlap = 15%
 348 infill_speed = 80
 349 interface_shells = 0
 350 layer_height = 0.2
 351 max_print_speed = 80
 352 max_volumetric_speed = 0
 353 min_skirt_length = 0
 354 notes =
 355 only_retract_when_crossing_perimeters = 0
 356 ooze_prevention = 0
 357 output_filename_format = [input_filename_base].gcode
 358 overhangs = 1
 359 perimeter_acceleration = 0
 360 perimeter_extruder = 1
 361 perimeter_extrusion_width = 0
 362 perimeter_speed = 60
 363 perimeters = 3
 364 post_process =
 365 raft_layers = 0
 366 resolution = 0
 367 seam_position = aligned
 368 skirt_distance = 10
 369 skirt_height = 1
 370 skirts = 1
 371 small_perimeter_speed = 20
 372 solid_infill_below_area = 30
 373 solid_infill_every_layers = 0
 374 solid_infill_extruder = 1
 375 solid_infill_extrusion_width = 0
 376 solid_infill_speed = 20
 377 spiral_vase = 0
 378 standby_temperature_delta = -5
 379 support_material = 0
 380 support_material_angle = 0
 381 support_material_contact_distance = 0.2
 382 support_material_enforce_layers = 0
 383 support_material_extruder = 1
 384 support_material_extrusion_width = 0
 385 support_material_interface_extruder = 1
 386 support_material_interface_layers = 0
 387 support_material_interface_spacing = 0
 388 support_material_interface_speed = 100%
 389 support_material_pattern = rectilinear
 390 support_material_spacing = 2.5
 391 support_material_speed = 60
 392 support_material_threshold = 45
 393 thin_walls = 1
 394 threads = 2
 395 top_infill_extrusion_width = 0
 396 top_solid_infill_speed = 20
 397 top_solid_layers = 3
 398 travel_speed = 100
 399 xy_size_compensation = 0
 400
 401 [print:Lulzbot fine sup]
 402 avoid_crossing_perimeters = 1
 403 bottom_solid_layers = 2
 404 bridge_acceleration = 0
 405 bridge_flow_ratio = 1
 406 bridge_speed = 40
 407 brim_width = 3
 408 complete_objects = 0
 409 default_acceleration = 0
 410 dont_support_bridges = 1
 411 external_fill_pattern = rectilinear
 412 external_perimeter_extrusion_width = 0
 413 external_perimeter_speed = 50%
 414 external_perimeters_first = 0
 415 extra_perimeters = 1
 416 extruder_clearance_height = 20
 417 extruder_clearance_radius = 20
 418 extrusion_width = 0
 419 fill_angle = 35
 420 fill_density = 15%
 421 fill_pattern = 3dhoneycomb
 422 first_layer_acceleration = 0
 423 first_layer_extrusion_width = 0
 424 first_layer_height = 0.2
 425 first_layer_speed = 10
 426 gap_fill_speed = 20
 427 gcode_comments = 0
 428 infill_acceleration = 0
 429 infill_every_layers = 1
 430 infill_extruder = 1
 431 infill_extrusion_width = 110%
 432 infill_first = 0
 433 infill_only_where_needed = 0
 434 infill_overlap = 15%
 435 infill_speed = 80
 436 interface_shells = 0
 437 layer_height = 0.2
 438 max_print_speed = 80
 439 max_volumetric_speed = 0
 440 min_skirt_length = 0
 441 notes =
 442 only_retract_when_crossing_perimeters = 0
 443 ooze_prevention = 0
 444 output_filename_format = [input_filename_base].gcode
 445 overhangs = 1
 446 perimeter_acceleration = 0
 447 perimeter_extruder = 1
 448 perimeter_extrusion_width = 0
 449 perimeter_speed = 60
 450 perimeters = 3
 451 post_process =
 452 raft_layers = 0
 453 resolution = 0
 454 seam_position = aligned
 455 skirt_distance = 10
 456 skirt_height = 1
 457 skirts = 1
 458 small_perimeter_speed = 20
 459 solid_infill_below_area = 30
 460 solid_infill_every_layers = 0
 461 solid_infill_extruder = 1
 462 solid_infill_extrusion_width = 0
 463 solid_infill_speed = 20
 464 spiral_vase = 0
 465 standby_temperature_delta = -5
 466 support_material = 1
 467 support_material_angle = 0
 468 support_material_contact_distance = 0.2
 469 support_material_enforce_layers = 0
 470 support_material_extruder = 1
 471 support_material_extrusion_width = 0
 472 support_material_interface_extruder = 1
 473 support_material_interface_layers = 3
 474 support_material_interface_spacing = 0
 475 support_material_interface_speed = 100%
 476 support_material_pattern = honeycomb
 477 support_material_spacing = 2.5
 478 support_material_speed = 60
 479 support_material_threshold = 45
 480 thin_walls = 1
 481 threads = 2
 482 top_infill_extrusion_width = 0
 483 top_solid_infill_speed = 20
 484 top_solid_layers = 3
 485 travel_speed = 100
 486 xy_size_compensation = 0
 487
 488 [print:MendelPro]
 489 avoid_crossing_perimeters = 0
 490 bottom_solid_layers = 3
 491 bridge_acceleration = 0
 492 bridge_flow_ratio = 1
 493 bridge_speed = 40
 494 brim_width = 1
 495 complete_objects = 0
 496 default_acceleration = 0
 497 dont_support_bridges = 1
 498 external_fill_pattern = rectilinear
 499 external_perimeter_extrusion_width = 0
 500 external_perimeter_speed = 20
 501 external_perimeters_first = 0
 502 extra_perimeters = 1
 503 extruder_clearance_height = 20
 504 extruder_clearance_radius = 20
 505 extrusion_width = 0
 506 fill_angle = 45
 507 fill_density = 15%
 508 fill_pattern = 3dhoneycomb
 509 first_layer_acceleration = 0
 510 first_layer_extrusion_width = 0
 511 first_layer_height = 0.2
 512 first_layer_speed = 10
 513 gap_fill_speed = 10
 514 gcode_comments = 0
 515 infill_acceleration = 0
 516 infill_every_layers = 1
 517 infill_extruder = 1
 518 infill_extrusion_width = 0
 519 infill_first = 0
 520 infill_only_where_needed = 0
 521 infill_overlap = 15%
 522 infill_speed = 0
 523 interface_shells = 0
 524 layer_height = 0.2
 525 max_print_speed = 80
 526 max_volumetric_speed = 0
 527 min_skirt_length = 2
 528 notes =
 529 only_retract_when_crossing_perimeters = 1
 530 ooze_prevention = 0
 531 output_filename_format = [input_filename_base].gcode
 532 overhangs = 1
 533 perimeter_acceleration = 0
 534 perimeter_extruder = 1
 535 perimeter_extrusion_width = 0
 536 perimeter_speed = 0
 537 perimeters = 2
 538 post_process =
 539 raft_layers = 0
 540 resolution = 0
 541 seam_position = aligned
 542 skirt_distance = 1
 543 skirt_height = 1
 544 skirts = 1
 545 small_perimeter_speed = 10
 546 solid_infill_below_area = 70
 547 solid_infill_every_layers = 0
 548 solid_infill_extruder = 1
 549 solid_infill_extrusion_width = 0
 550 solid_infill_speed = 0
 551 spiral_vase = 0
 552 standby_temperature_delta = -5
 553 support_material = 0
 554 support_material_angle = 0
 555 support_material_contact_distance = 0.2
 556 support_material_enforce_layers = 0
 557 support_material_extruder = 1
 558 support_material_extrusion_width = 0
 559 support_material_interface_extruder = 1
 560 support_material_interface_layers = 2
 561 support_material_interface_spacing = 0
 562 support_material_interface_speed = 100%
 563 support_material_pattern = rectilinear
 564 support_material_spacing = 5
 565 support_material_speed = 60
 566 support_material_threshold = 40
 567 thin_walls = 1
 568 threads = 2
 569 top_infill_extrusion_width = 0
 570 top_solid_infill_speed = 20
 571 top_solid_layers = 3
 572 travel_speed = 100
 573 xy_size_compensation = 0
 574
 575 [print:MendelPro fast]
 576 avoid_crossing_perimeters = 0
 577 bottom_solid_layers = 3
 578 bridge_acceleration = 0
 579 bridge_flow_ratio = 1
 580 bridge_speed = 40
 581 brim_width = 0
 582 complete_objects = 0
 583 default_acceleration = 0
 584 dont_support_bridges = 1
 585 external_fill_pattern = rectilinear
 586 external_perimeter_extrusion_width = 0
 587 external_perimeter_speed = 20
 588 external_perimeters_first = 0
 589 extra_perimeters = 1
 590 extruder_clearance_height = 20
 591 extruder_clearance_radius = 20
 592 extrusion_width = 0
 593 fill_angle = 45
 594 fill_density = 15%
 595 fill_pattern = 3dhoneycomb
 596 first_layer_acceleration = 0
 597 first_layer_extrusion_width = 0
 598 first_layer_height = 0.2
 599 first_layer_speed = 10
 600 gap_fill_speed = 10
 601 gcode_comments = 0
 602 infill_acceleration = 0
 603 infill_every_layers = 1
 604 infill_extruder = 1
 605 infill_extrusion_width = 0
 606 infill_first = 0
 607 infill_only_where_needed = 0
 608 infill_overlap = 15%
 609 infill_speed = 0
 610 interface_shells = 0
 611 layer_height = 0.5
 612 max_print_speed = 80
 613 max_volumetric_speed = 0
 614 min_skirt_length = 2
 615 notes =
 616 only_retract_when_crossing_perimeters = 1
 617 ooze_prevention = 0
 618 output_filename_format = [input_filename_base].gcode
 619 overhangs = 1
 620 perimeter_acceleration = 0
 621 perimeter_extruder = 1
 622 perimeter_extrusion_width = 0
 623 perimeter_speed = 0
 624 perimeters = 2
 625 post_process =
 626 raft_layers = 0
 627 resolution = 0
 628 seam_position = aligned
 629 skirt_distance = 1
 630 skirt_height = 1
 631 skirts = 1
 632 small_perimeter_speed = 10
 633 solid_infill_below_area = 70
 634 solid_infill_every_layers = 0
 635 solid_infill_extruder = 1
 636 solid_infill_extrusion_width = 0
 637 solid_infill_speed = 0
 638 spiral_vase = 0
 639 standby_temperature_delta = -5
 640 support_material = 0
 641 support_material_angle = 0
 642 support_material_contact_distance = 0.2
 643 support_material_enforce_layers = 0
 644 support_material_extruder = 1
 645 support_material_extrusion_width = 0
 646 support_material_interface_extruder = 1
 647 support_material_interface_layers = 2
 648 support_material_interface_spacing = 0
 649 support_material_interface_speed = 100%
 650 support_material_pattern = rectilinear
 651 support_material_spacing = 5
 652 support_material_speed = 60
 653 support_material_threshold = 40
 654 thin_walls = 1
 655 threads = 2
 656 top_infill_extrusion_width = 0
 657 top_solid_infill_speed = 20
 658 top_solid_layers = 3
 659 travel_speed = 100
 660 xy_size_compensation = 0
 661
 662 [print:MendelProSup]
 663 avoid_crossing_perimeters = 0
 664 bottom_solid_layers = 3
 665 bridge_acceleration = 0
 666 bridge_flow_ratio = 1
 667 bridge_speed = 40
 668 brim_width = 3
 669 complete_objects = 0
 670 default_acceleration = 0
 671 dont_support_bridges = 1
 672 external_fill_pattern = rectilinear
 673 external_perimeter_extrusion_width = 0
 674 external_perimeter_speed = 20
 675 external_perimeters_first = 0
 676 extra_perimeters = 1
 677 extruder_clearance_height = 20
 678 extruder_clearance_radius = 20
 679 extrusion_width = 0
 680 fill_angle = 45
 681 fill_density = 15%
 682 fill_pattern = 3dhoneycomb
 683 first_layer_acceleration = 0
 684 first_layer_extrusion_width = 0
 685 first_layer_height = 0.2
 686 first_layer_speed = 10
 687 gap_fill_speed = 10
 688 gcode_comments = 0
 689 infill_acceleration = 0
 690 infill_every_layers = 1
 691 infill_extruder = 1
 692 infill_extrusion_width = 0
 693 infill_first = 0
 694 infill_only_where_needed = 0
 695 infill_overlap = 15%
 696 infill_speed = 0
 697 interface_shells = 0
 698 layer_height = 0.2
 699 max_print_speed = 80
 700 max_volumetric_speed = 0
 701 min_skirt_length = 2
 702 notes =
 703 only_retract_when_crossing_perimeters = 1
 704 ooze_prevention = 0
 705 output_filename_format = [input_filename_base].gcode
 706 overhangs = 1
 707 perimeter_acceleration = 0
 708 perimeter_extruder = 1
 709 perimeter_extrusion_width = 0
 710 perimeter_speed = 0
 711 perimeters = 2
 712 post_process =
 713 raft_layers = 0
 714 resolution = 0
 715 seam_position = aligned
 716 skirt_distance = 1
 717 skirt_height = 1
 718 skirts = 1
 719 small_perimeter_speed = 10
 720 solid_infill_below_area = 70
 721 solid_infill_every_layers = 0
 722 solid_infill_extruder = 1
 723 solid_infill_extrusion_width = 0
 724 solid_infill_speed = 0
 725 spiral_vase = 0
 726 standby_temperature_delta = -5
 727 support_material = 1
 728 support_material_angle = 0
 729 support_material_contact_distance = 0.2
 730 support_material_enforce_layers = 0
 731 support_material_extruder = 1
 732 support_material_extrusion_width = 0
 733 support_material_interface_extruder = 1
 734 support_material_interface_layers = 3
 735 support_material_interface_spacing = 0
 736 support_material_interface_speed = 100%
 737 support_material_pattern = honeycomb
 738 support_material_spacing = 2.5
 739 support_material_speed = 60
 740 support_material_threshold = 40
 741 thin_walls = 1
 742 threads = 2
 743 top_infill_extrusion_width = 0
 744 top_solid_infill_speed = 20
 745 top_solid_layers = 3
 746 travel_speed = 100
 747 xy_size_compensation = 0
 748
 749 [print:TinyBoy]
 750 avoid_crossing_perimeters = 0
 751 bottom_solid_layers = 3
 752 bridge_acceleration = 0
 753 bridge_flow_ratio = 1
 754 bridge_speed = 40
 755 brim_width = 0
 756 complete_objects = 0
 757 default_acceleration = 0
 758 dont_support_bridges = 1
 759 external_fill_pattern = rectilinear
 760 external_perimeter_extrusion_width = 0
 761 external_perimeter_speed = 20
 762 external_perimeters_first = 0
 763 extra_perimeters = 1
 764 extruder_clearance_height = 20
 765 extruder_clearance_radius = 20
 766 extrusion_width = 0
 767 fill_angle = 45
 768 fill_density = 20%
 769 fill_pattern = 3dhoneycomb
 770 first_layer_acceleration = 0
 771 first_layer_extrusion_width = 0
 772 first_layer_height = 0.2
 773 first_layer_speed = 10
 774 gap_fill_speed = 20
 775 gcode_comments = 0
 776 infill_acceleration = 0
 777 infill_every_layers = 1
 778 infill_extruder = 1
 779 infill_extrusion_width = 0
 780 infill_first = 0
 781 infill_only_where_needed = 0
 782 infill_overlap = 15%
 783 infill_speed = 0
 784 interface_shells = 0
 785 layer_height = 0.2
 786 max_print_speed = 80
 787 max_volumetric_speed = 0
 788 min_skirt_length = 1
 789 notes =
 790 only_retract_when_crossing_perimeters = 1
 791 ooze_prevention = 0
 792 output_filename_format = [input_filename_base].gcode
 793 overhangs = 1
 794 perimeter_acceleration = 0
 795 perimeter_extruder = 1
 796 perimeter_extrusion_width = 0
 797 perimeter_speed = 0
 798 perimeters = 2
 799 post_process =
 800 raft_layers = 0
 801 resolution = 0
 802 seam_position = aligned
 803 skirt_distance = 1
 804 skirt_height = 1
 805 skirts = 1
 806 small_perimeter_speed = 0
 807 solid_infill_below_area = 70
 808 solid_infill_every_layers = 0
 809 solid_infill_extruder = 1
 810 solid_infill_extrusion_width = 0
 811 solid_infill_speed = 0
 812 spiral_vase = 0
 813 standby_temperature_delta = -5
 814 support_material = 0
 815 support_material_angle = 0
 816 support_material_contact_distance = 0.2
 817 support_material_enforce_layers = 0
 818 support_material_extruder = 1
 819 support_material_extrusion_width = 0
 820 support_material_interface_extruder = 1
 821 support_material_interface_layers = 2
 822 support_material_interface_spacing = 0
 823 support_material_interface_speed = 100%
 824 support_material_pattern = rectilinear
 825 support_material_spacing = 5
 826 support_material_speed = 0
 827 support_material_threshold = 40
 828 thin_walls = 1
 829 threads = 2
 830 top_infill_extrusion_width = 0
 831 top_solid_infill_speed = 20
 832 top_solid_layers = 4
 833 travel_speed = 100
 834 xy_size_compensation = 0
 835
 836 [print:TinyBoy sup]
 837 avoid_crossing_perimeters = 0
 838 bottom_solid_layers = 3
 839 bridge_acceleration = 0
 840 bridge_flow_ratio = 1
 841 bridge_speed = 40
 842 brim_width = 0
 843 complete_objects = 0
 844 default_acceleration = 0
 845 dont_support_bridges = 1
 846 external_fill_pattern = rectilinear
 847 external_perimeter_extrusion_width = 0
 848 external_perimeter_speed = 20
 849 external_perimeters_first = 0
 850 extra_perimeters = 1
 851 extruder_clearance_height = 20
 852 extruder_clearance_radius = 20
 853 extrusion_width = 0
 854 fill_angle = 45
 855 fill_density = 20%
 856 fill_pattern = 3dhoneycomb
 857 first_layer_acceleration = 0
 858 first_layer_extrusion_width = 0
 859 first_layer_height = 0.2
 860 first_layer_speed = 10
 861 gap_fill_speed = 20
 862 gcode_comments = 0
 863 infill_acceleration = 0
 864 infill_every_layers = 1
 865 infill_extruder = 1
 866 infill_extrusion_width = 0
 867 infill_first = 0
 868 infill_only_where_needed = 0
 869 infill_overlap = 15%
 870 infill_speed = 0
 871 interface_shells = 0
 872 layer_height = 0.2
 873 max_print_speed = 80
 874 max_volumetric_speed = 0
 875 min_skirt_length = 1
 876 notes =
 877 only_retract_when_crossing_perimeters = 1
 878 ooze_prevention = 0
 879 output_filename_format = [input_filename_base].gcode
 880 overhangs = 1
 881 perimeter_acceleration = 0
 882 perimeter_extruder = 1
 883 perimeter_extrusion_width = 0
 884 perimeter_speed = 0
 885 perimeters = 2
 886 post_process =
 887 raft_layers = 0
 888 resolution = 0
 889 seam_position = aligned
 890 skirt_distance = 1
 891 skirt_height = 1
 892 skirts = 1
 893 small_perimeter_speed = 0
 894 solid_infill_below_area = 70
 895 solid_infill_every_layers = 0
 896 solid_infill_extruder = 1
 897 solid_infill_extrusion_width = 0
 898 solid_infill_speed = 0
 899 spiral_vase = 0
 900 standby_temperature_delta = -5
 901 support_material = 1
 902 support_material_angle = 0
 903 support_material_contact_distance = 0.3
 904 support_material_enforce_layers = 0
 905 support_material_extruder = 1
 906 support_material_extrusion_width = 0
 907 support_material_interface_extruder = 1
 908 support_material_interface_layers = 2
 909 support_material_interface_spacing = 0
 910 support_material_interface_speed = 100%
 911 support_material_pattern = rectilinear
 912 support_material_spacing = 5
 913 support_material_speed = 0
 914 support_material_threshold = 40
 915 thin_walls = 1
 916 threads = 2
 917 top_infill_extrusion_width = 0
 918 top_solid_infill_speed = 20
 919 top_solid_layers = 4
 920 travel_speed = 100
 921 xy_size_compensation = 0
 922
 923 [print:Toy]
 924 avoid_crossing_perimeters = 0
 925 bottom_solid_layers = 2
 926 bridge_acceleration = 0
 927 bridge_flow_ratio = 1
 928 bridge_speed = 0
 929 brim_width = 0
 930 complete_objects = 0
 931 default_acceleration = 0
 932 dont_support_bridges = 1
 933 external_fill_pattern = rectilinear
 934 external_perimeter_extrusion_width = 0
 935 external_perimeter_speed = 0
 936 external_perimeters_first = 0
 937 extra_perimeters = 1
 938 extruder_clearance_height = 20
 939 extruder_clearance_radius = 20
 940 extrusion_width = 0
 941 fill_angle = 45
 942 fill_density = 0%
 943 fill_pattern = rectilinear
 944 first_layer_acceleration = 0
 945 first_layer_extrusion_width = 0
 946 first_layer_height = 0.2
 947 first_layer_speed = 10
 948 gap_fill_speed = 0
 949 gcode_comments = 0
 950 infill_acceleration = 0
 951 infill_every_layers = 1
 952 infill_extruder = 1
 953 infill_extrusion_width = 0
 954 infill_first = 0
 955 infill_only_where_needed = 0
 956 infill_overlap = 15%
 957 infill_speed = 0
 958 interface_shells = 0
 959 layer_height = 0.2
 960 max_print_speed = 10
 961 max_volumetric_speed = 0
 962 min_skirt_length = 1
 963 notes =
 964 only_retract_when_crossing_perimeters = 1
 965 ooze_prevention = 0
 966 output_filename_format = [input_filename_base].gcode
 967 overhangs = 1
 968 perimeter_acceleration = 0
 969 perimeter_extruder = 1
 970 perimeter_extrusion_width = 0
 971 perimeter_speed = 0
 972 perimeters = 2
 973 post_process =
 974 raft_layers = 0
 975 resolution = 0
 976 seam_position = aligned
 977 skirt_distance = 1
 978 skirt_height = 1
 979 skirts = 1
 980 small_perimeter_speed = 0
 981 solid_infill_below_area = 70
 982 solid_infill_every_layers = 0
 983 solid_infill_extruder = 1
 984 solid_infill_extrusion_width = 0
 985 solid_infill_speed = 0
 986 spiral_vase = 0
 987 standby_temperature_delta = -5
 988 support_material = 1
 989 support_material_angle = 0
 990 support_material_contact_distance = 0.3
 991 support_material_enforce_layers = 0
 992 support_material_extruder = 1
 993 support_material_extrusion_width = 0
 994 support_material_interface_extruder = 1
 995 support_material_interface_layers = 3
 996 support_material_interface_spacing = 0
 997 support_material_interface_speed = 100%
 998 support_material_pattern = rectilinear
 999 support_material_spacing = 5
1000 support_material_speed = 0
1001 support_material_threshold = 40
1002 thin_walls = 1
1003 threads = 2
1004 top_infill_extrusion_width = 0
1005 top_solid_infill_speed = 0
1006 top_solid_layers = 0
1007 travel_speed = 100
1008 xy_size_compensation = 0
1009
1010 [print:prusa i3 200]
1011 avoid_crossing_perimeters = 0
1012 bottom_solid_layers = 3
1013 bridge_acceleration = 0
1014 bridge_flow_ratio = 1
1015 bridge_speed = 40
1016 brim_width = 5
1017 complete_objects = 0
1018 default_acceleration = 0
1019 dont_support_bridges = 1
1020 external_fill_pattern = rectilinear
1021 external_perimeter_extrusion_width = 0
1022 external_perimeter_speed = 20
1023 external_perimeters_first = 0
1024 extra_perimeters = 1
1025 extruder_clearance_height = 20
1026 extruder_clearance_radius = 20
1027 extrusion_width = 0
1028 fill_angle = 45
1029 fill_density = 20%
1030 fill_pattern = 3dhoneycomb
1031 first_layer_acceleration = 0
1032 first_layer_extrusion_width = 0
1033 first_layer_height = 0.2
1034 first_layer_speed = 15
1035 gap_fill_speed = 20
1036 gcode_comments = 0
1037 infill_acceleration = 0
1038 infill_every_layers = 1
1039 infill_extruder = 1
1040 infill_extrusion_width = 0
1041 infill_first = 0
1042 infill_only_where_needed = 0
1043 infill_overlap = 15%
1044 infill_speed = 0
1045 interface_shells = 0
1046 layer_height = 0.2
1047 max_print_speed = 60
1048 max_volumetric_speed = 0
1049 min_skirt_length = 1
1050 notes =
1051 only_retract_when_crossing_perimeters = 1
1052 ooze_prevention = 0
1053 output_filename_format = [input_filename_base].gcode
1054 overhangs = 1
1055 perimeter_acceleration = 0
1056 perimeter_extruder = 1
1057 perimeter_extrusion_width = 0
1058 perimeter_speed = 0
1059 perimeters = 2
1060 post_process =
1061 raft_layers = 0
1062 resolution = 0
1063 seam_position = aligned
1064 skirt_distance = 1
1065 skirt_height = 1
1066 skirts = 1
1067 small_perimeter_speed = 15
1068 solid_infill_below_area = 70
1069 solid_infill_every_layers = 0
1070 solid_infill_extruder = 1
1071 solid_infill_extrusion_width = 0
1072 solid_infill_speed = 0
1073 spiral_vase = 0
1074 standby_temperature_delta = -5
1075 support_material = 0
1076 support_material_angle = 0
1077 support_material_contact_distance = 0
1078 support_material_enforce_layers = 0
1079 support_material_extruder = 1
1080 support_material_extrusion_width = 0
1081 support_material_interface_extruder = 1
1082 support_material_interface_layers = 2
1083 support_material_interface_spacing = 0
1084 support_material_interface_speed = 10
1085 support_material_pattern = pillars
1086 support_material_spacing = 2.5
1087 support_material_speed = 40
1088 support_material_threshold = 40
1089 thin_walls = 1
1090 threads = 2
1091 top_infill_extrusion_width = 0
1092 top_solid_infill_speed = 20
1093 top_solid_layers = 3
1094 travel_speed = 100
1095 xy_size_compensation = 0
1096
1097 [print:prusa i3 200 sup]
1098 avoid_crossing_perimeters = 0
1099 bottom_solid_layers = 3
1100 bridge_acceleration = 0
1101 bridge_flow_ratio = 1
1102 bridge_speed = 40
1103 brim_width = 5
1104 complete_objects = 0
1105 default_acceleration = 0
1106 dont_support_bridges = 1
1107 external_fill_pattern = rectilinear
1108 external_perimeter_extrusion_width = 0
1109 external_perimeter_speed = 20
1110 external_perimeters_first = 0
1111 extra_perimeters = 1
1112 extruder_clearance_height = 20
1113 extruder_clearance_radius = 20
1114 extrusion_width = 0
1115 fill_angle = 45
1116 fill_density = 20%
1117 fill_pattern = 3dhoneycomb
1118 first_layer_acceleration = 0
1119 first_layer_extrusion_width = 0
1120 first_layer_height = 0.2
1121 first_layer_speed = 15
1122 gap_fill_speed = 20
1123 gcode_comments = 0
1124 infill_acceleration = 0
1125 infill_every_layers = 1
1126 infill_extruder = 1
1127 infill_extrusion_width = 0
1128 infill_first = 0
1129 infill_only_where_needed = 0
1130 infill_overlap = 15%
1131 infill_speed = 0
1132 interface_shells = 0
1133 layer_height = 0.2
1134 max_print_speed = 60
1135 max_volumetric_speed = 0
1136 min_skirt_length = 1
1137 notes =
1138 only_retract_when_crossing_perimeters = 1
1139 ooze_prevention = 0
1140 output_filename_format = [input_filename_base].gcode
1141 overhangs = 1
1142 perimeter_acceleration = 0
1143 perimeter_extruder = 1
1144 perimeter_extrusion_width = 0
1145 perimeter_speed = 0
1146 perimeters = 2
1147 post_process =
1148 raft_layers = 1
1149 resolution = 0
1150 seam_position = aligned
1151 skirt_distance = 1
1152 skirt_height = 1
1153 skirts = 1
1154 small_perimeter_speed = 15
1155 solid_infill_below_area = 70
1156 solid_infill_every_layers = 0
1157 solid_infill_extruder = 1
1158 solid_infill_extrusion_width = 0
1159 solid_infill_speed = 0
1160 spiral_vase = 0
1161 standby_temperature_delta = -5
1162 support_material = 1
1163 support_material_angle = 0
1164 support_material_contact_distance = 0.2
1165 support_material_enforce_layers = 0
1166 support_material_extruder = 1
1167 support_material_extrusion_width = 0
1168 support_material_interface_extruder = 1
1169 support_material_interface_layers = 2
1170 support_material_interface_spacing = 0
1171 support_material_interface_speed = 10
1172 support_material_pattern = pillars
1173 support_material_spacing = 2.5
1174 support_material_speed = 40
1175 support_material_threshold = 40
1176 thin_walls = 1
1177 threads = 2
1178 top_infill_extrusion_width = 0
1179 top_solid_infill_speed = 20
1180 top_solid_layers = 3
1181 travel_speed = 100
1182 xy_size_compensation = 0
1183
1184 [printer:Lulzbot]
1185 bed_shape = 0x0,298x0,298x275,0x275
1186 before_layer_gcode =
1187 end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
1188 extruder_offset = 0x0
1189 gcode_flavor = reprap
1190 layer_gcode =
1191 nozzle_diameter = 0.35
1192 octoprint_apikey =
1193 octoprint_host =
1194 pressure_advance = 0
1195 retract_before_travel = 2
1196 retract_layer_change = 1
1197 retract_length = 2
1198 retract_length_toolchange = 3
1199 retract_lift = 0
1200 retract_restart_extra = 0
1201 retract_restart_extra_toolchange = 0
1202 retract_speed = 20
1203 start_gcode = G28 ; home all axes\n
1204 toolchange_gcode =
1205 use_firmware_retraction = 0
1206 use_relative_e_distances = 0
1207 use_volumetric_e = 0
1208 vibration_limit = 0
1209 wipe = 0
1210 z_offset = 0
1211
1212 [printer:MendelPro]
1213 bed_shape = 0x0,220x0,220x177,0x177
1214 before_layer_gcode =
1215 end_gcode = M104 S0        ; turn off temperature\nM140 S0;\nG28 X0           ; home X axis\nG0 Y177;\nM84               ; disable motors\n
1216 extruder_offset = 0x0
1217 gcode_flavor = reprap
1218 layer_gcode =
1219 nozzle_diameter = 0.5
1220 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
1221 octoprint_host =
1222 pressure_advance = 0
1223 retract_before_travel = 2
1224 retract_layer_change = 1
1225 retract_length = 5
1226 retract_length_toolchange = 10
1227 retract_lift = 0
1228 retract_restart_extra = 0
1229 retract_restart_extra_toolchange = 0
1230 retract_speed = 40
1231 start_gcode = G28 Z            ; home Z\nG28 X Y         ; home X Y\n
1232 toolchange_gcode =
1233 use_firmware_retraction = 0
1234 use_relative_e_distances = 0
1235 use_volumetric_e = 0
1236 vibration_limit = 0
1237 wipe = 0
1238 z_offset = 0
1239
1240 [printer:TinyBoy]
1241 bed_shape = 0x0,88x0,88x74,0x74
1242 before_layer_gcode =
1243 end_gcode = M104 S0        ; turn off temperature\nG28 X0           ; home X axis\nM84               ; disable motors\n
1244 extruder_offset = 0x0
1245 gcode_flavor = reprap
1246 layer_gcode =
1247 nozzle_diameter = 0.4
1248 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
1249 octoprint_host =
1250 pressure_advance = 0
1251 retract_before_travel = 2
1252 retract_layer_change = 1
1253 retract_length = 5
1254 retract_length_toolchange = 10
1255 retract_lift = 0
1256 retract_restart_extra = 0
1257 retract_restart_extra_toolchange = 0
1258 retract_speed = 40
1259 start_gcode = G28 Z            ; home Z\nG0 Z 1          ; lift Z\nG28 X Y         ; home X Y\n
1260 toolchange_gcode =
1261 use_firmware_retraction = 0
1262 use_relative_e_distances = 0
1263 use_volumetric_e = 0
1264 vibration_limit = 0
1265 wipe = 0
1266 z_offset = 0
1267
1268 [printer:Toyrep]
1269 bed_shape = 0x0,125x0,125x125,0x125
1270 before_layer_gcode =
1271 end_gcode = M104 S0 ; turn off nozzle temperature\nM84 ; disable motors
1272 extruder_offset = 0x0
1273 gcode_flavor = reprap
1274 layer_gcode =
1275 nozzle_diameter = 0.4
1276 octoprint_apikey =
1277 octoprint_host =
1278 pressure_advance = 0
1279 retract_before_travel = 2
1280 retract_layer_change = 1
1281 retract_length = 0
1282 retract_length_toolchange = 3
1283 retract_lift = 0
1284 retract_restart_extra = 0
1285 retract_restart_extra_toolchange = 0
1286 retract_speed = 10
1287 start_gcode = \n
1288 toolchange_gcode =
1289 use_firmware_retraction = 0
1290 use_relative_e_distances = 0
1291 use_volumetric_e = 0
1292 vibration_limit = 0
1293 wipe = 0
1294 z_offset = 0
1295
1296 [printer:prusa i3]
1297 bed_shape = 0x0,190x0,190x190,0x190
1298 before_layer_gcode =
1299 end_gcode = M104 S0        ; turn off temperature\nM140 S0        ; turn off bed temp \nG28 X0           ; home X axis\nG0 Y190         ; präsent object\nM84               ; disable motors\nM81               ; Power off\n\n
1300 extruder_offset = 0x0
1301 gcode_flavor = reprap
1302 layer_gcode =
1303 nozzle_diameter = 0.4
1304 octoprint_apikey = 176444E92BFF48819CE0D8F1B264A91C
1305 octoprint_host =
1306 pressure_advance = 0
1307 retract_before_travel = 2
1308 retract_layer_change = 1
1309 retract_length = 5
1310 retract_length_toolchange = 10
1311 retract_lift = 0
1312 retract_restart_extra = 0
1313 retract_restart_extra_toolchange = 0
1314 retract_speed = 40
1315 start_gcode = G28 Z            ; home Z\nG0 Z1            ; lift Z\nG28 X Y         ; home X Y\nG0         Y40 ; clab move
1316 toolchange_gcode = M83 ; turn on relative movement for extruder  \nG1 E-5  ; retract filament 5mm  \nG1 X10 Y10 Z4.000000  ; home X and Y axis leave Z at current height  \nM84 E ; release extruder stepper motor from 'holding' position  \n@pause ; pause print!  \nG1 E0 ; reset extruder, ready to push out plastic again  \nM82 ; set extruder movement back to absolute ready for next layer
1317 use_firmware_retraction = 0
1318 use_relative_e_distances = 0
1319 use_volumetric_e = 0
1320 vibration_limit = 0
1321 wipe = 0
1322 z_offset = 0
1323
1324 [settings]
1325 autocenter = 1
1326 mode = expert