RepRap%2FConfigs%2FSlic3r%2FSintox%2Fabs_gross.ini.mw

   1 avoid_crossing_perimeters = 0
   2 bed_shape = 0x0,200x0,200x200,0x200
   3 bed_temperature = 80
   4 bottom_solid_layers = 3
   5 bridge_acceleration = 0
   6 bridge_fan_speed = 100
   7 bridge_flow_ratio = 1
   8 bridge_speed = 60
   9 brim_width = 0
  10 complete_objects = 0
  11 cooling = 1
  12 default_acceleration = 0
  13 disable_fan_first_layers = 1
  14 dont_support_bridges = 1
  15 duplicate_distance = 6
  16 end_gcode = M84     ; disable motors\nM104 S0 ; turn off extruder temperature\nG0 X0    ; move X axis to 0\nG1 Y198 F6000 ; drive print table all the way out\nM84     ; disable motors\n
  17 external_perimeter_extrusion_width = 0
  18 external_perimeter_speed = 70%
  19 external_perimeters_first = 0
  20 extra_perimeters = 1
  21 extruder_clearance_height = 20
  22 extruder_clearance_radius = 20
  23 extruder_offset = 0x0
  24 extrusion_axis = E
  25 extrusion_multiplier = 1
  26 extrusion_width = 0
  27 fan_always_on = 1
  28 fan_below_layer_time = 60
  29 filament_diameter = 1.75
  30 fill_angle = 45
  31 fill_density = 35%
  32 fill_pattern = honeycomb
  33 first_layer_acceleration = 0
  34 first_layer_bed_temperature = 80
  35 first_layer_extrusion_width = 200%
  36 first_layer_height = 0.25
  37 first_layer_speed = 50%
  38 first_layer_temperature = 240
  39 gap_fill_speed = 20
  40 gcode_arcs = 0
  41 gcode_comments = 0
  42 gcode_flavor = reprap
  43 infill_acceleration = 0
  44 infill_every_layers = 1
  45 infill_extruder = 1
  46 infill_extrusion_width = 0
  47 infill_first = 0
  48 infill_only_where_needed = 0
  49 infill_speed = 70
  50 interface_shells = 0
  51 layer_gcode =
  52 layer_height = 0.2
  53 max_fan_speed = 100
  54 min_fan_speed = 35
  55 min_print_speed = 10
  56 min_skirt_length = 0
  57 notes =
  58 nozzle_diameter = 0.5
  59 only_retract_when_crossing_perimeters = 1
  60 ooze_prevention = 0
  61 output_filename_format = [input_filename_base].gcode
  62 overhangs = 1
  63 perimeter_acceleration = 0
  64 perimeter_extruder = 1
  65 perimeter_extrusion_width = 0
  66 perimeter_speed = 80
  67 perimeters = 3
  68 post_process =
  69 raft_layers = 0
  70 resolution = 0
  71 retract_before_travel = 2
  72 retract_layer_change = 1
  73 retract_length = 5
  74 retract_length_toolchange = 10
  75 retract_lift = 1
  76 retract_restart_extra = 0
  77 retract_restart_extra_toolchange = 0
  78 retract_speed = 40
  79 seam_position = aligned
  80 skirt_distance = 2
  81 skirt_height = 1
  82 skirts = 1
  83 slowdown_below_layer_time = 30
  84 small_perimeter_speed = 30
  85 solid_fill_pattern = rectilinear
  86 solid_infill_below_area = 70
  87 solid_infill_every_layers = 0
  88 solid_infill_extrusion_width = 0
  89 solid_infill_speed = 70
  90 spiral_vase = 0
  91 standby_temperature_delta = -5
  92 start_gcode = G28 X0 Y0 ; home X and Y\nG0 X60; move to X60\nG92 X0; set postition to X=0\nG92 Y40; set position to Y=0\nG28 Z0; home Z
  93 support_material = 1
  94 support_material_angle = 0
  95 support_material_enforce_layers = 0
  96 support_material_extruder = 1
  97 support_material_extrusion_width = 0
  98 support_material_interface_extruder = 1
  99 support_material_interface_layers = 3
 100 support_material_interface_spacing = 0
 101 support_material_interface_speed = 100%
 102 support_material_pattern = rectilinear
 103 support_material_spacing = 2.5
 104 support_material_speed = 20
 105 support_material_threshold = 0
 106 temperature = 240
 107 thin_walls = 1
 108 threads = 2
 109 toolchange_gcode =
 110 top_infill_extrusion_width = 0
 111 top_solid_infill_speed = 60
 112 top_solid_layers = 4
 113 travel_speed = 130
 114 use_firmware_retraction = 0
 115 use_relative_e_distances = 0
 116 vibration_limit = 0
 117 wipe = 0
 118 xy_size_compensation = 0
 119 z_offset = 0