ausgelagert aus [[RepRap/Configs/Slic3r]]
authorDaniel Bohrer <Daniel Bohrer@stratum0.org/mediawiki/>
Sun, 12 Oct 2014 21:48:25 +0000 (21:48 +0000)
committerDaniel Bohrer <Daniel Bohrer@stratum0.org/mediawiki/>
Sun, 12 Oct 2014 21:48:25 +0000 (21:48 +0000)
RepRap%2FConfigs%2FSlic3r%2Fnetz39.ini.mw [new file with mode: 0644]

diff --git a/RepRap%2FConfigs%2FSlic3r%2Fnetz39.ini.mw b/RepRap%2FConfigs%2FSlic3r%2Fnetz39.ini.mw
new file mode 100644 (file)
index 0000000..623333a
--- /dev/null
@@ -0,0 +1,112 @@
+# generated by Slic3r 0.9.9-dev on Mon Jun  3 17:06:48 2013
+avoid_crossing_perimeters = 0
+bed_size = 180,200
+bed_temperature = 50
+bottom_solid_layers = 5
+bridge_acceleration = 0
+bridge_fan_speed = 100
+bridge_flow_ratio = 1
+bridge_speed = 30
+brim_width = 0
+complete_objects = 1
+cooling = 
+default_acceleration = 0
+disable_fan_first_layers = 1
+duplicate = 1
+duplicate_distance = 6
+duplicate_grid = 1,1
+end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed temperature \nG28 X0    ; home X axis\nG92 Z0 E1\nG1 Z10 E0 F3000 ; retract extruder and filament\nG1 Y180 F6000 ; drive print table all the way out\nM84     ; disable motors
+external_perimeter_speed = 40%
+external_perimeters_first = 0
+extra_perimeters = 
+extruder_clearance_height = 35
+extruder_clearance_radius = 62
+extruder_offset = 0x0
+extrusion_axis = E
+extrusion_multiplier = 1.1
+extrusion_width = 0
+fan_always_on = 0
+fan_below_layer_time = 60
+filament_diameter = 1.75
+fill_angle = 30
+fill_density = 0.5
+fill_pattern = rectilinear
+first_layer_bed_temperature = 50
+first_layer_extrusion_width = 0
+first_layer_height = 150%
+first_layer_speed = 40%
+first_layer_temperature = 197
+g0 = 0
+gap_fill_speed = 20
+gcode_arcs = 0
+gcode_comments = 0
+gcode_flavor = reprap
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 0
+infill_first = 0
+infill_only_where_needed = 0
+infill_speed = 60
+layer_gcode = 
+layer_height = 0.2
+max_fan_speed = 100
+min_fan_speed = 35
+min_print_speed = 5
+min_skirt_length = 15
+notes = config for printing netz39 pieces
+nozzle_diameter = 0.33
+only_retract_when_crossing_perimeters = 1
+output_filename_format = [input_filename_base].gcode
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 60
+perimeters = 3
+post_process = 
+print_center = 90,100
+raft_layers = 0
+randomize_start = 
+resolution = 0
+retract_before_travel = 0
+retract_layer_change = 1
+retract_length = 2
+retract_length_toolchange = 5
+retract_lift = 0
+retract_restart_extra = 0
+retract_restart_extra_toolchange = 0
+retract_speed = 50
+rotate = 0
+scale = 1
+skirt_distance = 5
+skirt_height = 1
+skirts = 2
+slowdown_below_layer_time = 50
+small_perimeter_speed = 60%
+solid_fill_pattern = rectilinear
+solid_infill_below_area = 0
+solid_infill_every_layers = 0
+solid_infill_extrusion_width = 0
+solid_infill_speed = 100%
+start_gcode = G28 ; home all axes\nM92 E820
+support_material = 
+support_material_angle = 45
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_layers = 0
+support_material_interface_spacing = 0
+support_material_pattern = rectilinear
+support_material_spacing = 2
+support_material_speed = 60
+support_material_threshold = 41
+temperature = 188
+threads = 2
+toolchange_gcode = 
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 70%
+top_solid_layers = 5
+travel_speed = 100
+use_relative_e_distances = 0
+vibration_limit = 0
+z_offset = 0
This page took 0.032151 seconds and 4 git commands to generate.