core/usbhid-rom/usbhid.c

   1 /**************************************************************************/
   2 /*!
   3     @file     usbhid.c
   4     @author   K. Townsend (microBuilder.eu)
   5
   6     @section LICENSE
   7
   8     Software License Agreement (BSD License)
   9
  10     Copyright (c) 2010, microBuilder SARL
  11     All rights reserved.
  12
  13     Redistribution and use in source and binary forms, with or without
  14     modification, are permitted provided that the following conditions are met:
  15     1. Redistributions of source code must retain the above copyright
  16     notice, this list of conditions and the following disclaimer.
  17     2. Redistributions in binary form must reproduce the above copyright
  18     notice, this list of conditions and the following disclaimer in the
  19     documentation and/or other materials provided with the distribution.
  20     3. Neither the name of the copyright holders nor the
  21     names of its contributors may be used to endorse or promote products
  22     derived from this software without specific prior written permission.
  23
  24     THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
  25     EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
  26     WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  27     DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
  28     DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  29     (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
  30     LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  31     ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  32     (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
  33     SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  34 */
  35 /**************************************************************************/
  36 #include <string.h>
  37
  38 #include "core/usbhid-rom/usb.h"
  39 #include "core/usbhid-rom/usbconfig.h"
  40 #include "core/rom_drivers.h"
  41 #include "core/gpio/gpio.h"
  42 #include "core/adc/adc.h"
  43 #include "core/systick/systick.h"
  44
  45 #include "usbhid.h"
  46
  47 USB_DEV_INFO DeviceInfo;
  48 HID_DEVICE_INFO HidDevInfo;
  49 ROM ** rom = (ROM **)0x1fff1ff8;
  50
  51 typedef struct usbhid_out_s
  52 {
  53   uint16_t gpio1Dir;
  54   uint16_t gpio1Data;
  55   uint16_t gpio2Dir;
  56   uint16_t gpio2Data;
  57   uint16_t gpio3Dir;
  58   uint16_t gpio3Data;
  59   uint16_t adc0;
  60   uint16_t adc1;
  61   uint16_t adc2;
  62   uint16_t adc3;
  63   uint32_t systicks;
  64   uint32_t rollovers;
  65 } usbhid_out_t;
  66
  67 /**************************************************************************/
  68 /*!
  69     @brief Gets the HID In Report (the report going from the LPC1343 to
  70     the USB host)
  71 */
  72 /**************************************************************************/
  73 void usbHIDGetInReport (uint8_t src[], uint32_t length)
  74 {
  75   usbhid_out_t out;
  76
  77   out.gpio1Dir = GPIO_GPIO1DIR;
  78   out.gpio1Data = GPIO_GPIO1DATA;
  79   out.gpio2Dir = GPIO_GPIO2DIR;
  80   out.gpio2Data = GPIO_GPIO2DATA;
  81   out.gpio3Dir = GPIO_GPIO3DIR;
  82   out.gpio3Data = GPIO_GPIO3DATA;
  83   out.adc0 = adcRead(0);
  84   out.adc1 = adcRead(1);
  85   out.adc2 = adcRead(2);
  86   out.adc3 = adcRead(3);
  87   out.systicks = systickGetTicks();
  88   out.rollovers = systickGetRollovers();
  89
  90   size_t i = 0;
  91   memcpy(&src[i], &out.gpio1Dir, sizeof out.gpio1Dir);
  92   i += sizeof out.gpio1Dir;
  93   memcpy(&src[i], &out.gpio1Data, sizeof out.gpio1Data);
  94   i += sizeof out.gpio1Data;
  95   memcpy(&src[i], &out.gpio2Dir, sizeof out.gpio2Dir);
  96   i += sizeof out.gpio2Dir;
  97   memcpy(&src[i], &out.gpio2Data, sizeof out.gpio2Data);
  98   i += sizeof out.gpio2Data;
  99   memcpy(&src[i], &out.gpio3Dir, sizeof out.gpio3Dir);
 100   i += sizeof out.gpio3Dir;
 101   memcpy(&src[i], &out.gpio3Data, sizeof out.gpio3Data);
 102   i += sizeof out.gpio3Data;
 103   memcpy(&src[i], &out.adc0, sizeof out.adc0);
 104   i += sizeof out.adc0;
 105   memcpy(&src[i], &out.adc1, sizeof out.adc1);
 106   i += sizeof out.adc1;
 107   memcpy(&src[i], &out.adc2, sizeof out.adc2);
 108   i += sizeof out.adc2;
 109   memcpy(&src[i], &out.adc3, sizeof out.adc3);
 110   i += sizeof out.adc3;
 111   memcpy(&src[i], &out.systicks, sizeof out.systicks);
 112   i += sizeof out.systicks;
 113   memcpy(&src[i], &out.rollovers, sizeof out.rollovers);
 114   i += sizeof out.rollovers;
 115 }
 116
 117 /**************************************************************************/
 118 /*!
 119     @brief Sets the HID Out Report (the report coming in from the USB
 120     host to the LPC1343).
 121 */
 122 /**************************************************************************/
 123 void usbHIDSetOutReport (uint8_t dst[], uint32_t length)
 124 {
 125   uint8_t PCOutReportData = dst[0];
 126   // Check bit 0 in the incoming report to determine is LED should
 127   // be enabled or disabled (1 = enabled, 0 = disabled)
 128   if (PCOutReportData & (1<<0))
 129   {
 130     // Enable LED (set low)
 131     gpioSetValue (CFG_LED_PORT, CFG_LED_PIN, 0);
 132   }
 133   else
 134   {
 135     // Disable LED (set high)
 136     gpioSetValue (CFG_LED_PORT, CFG_LED_PIN, 1);
 137   }
 138 }
 139
 140 /**************************************************************************/
 141 /*!
 142     @brief Initialises the USB port
 143
 144     The ROM-based USB HID code is capable of configuring the PLL and pins
 145     for USB, but there seems to be a bug in the code that sets the system
 146     clock to 48MHz (normally the USB and System clocks can be configured
 147     seperately).  As such, this code does not use the "init_clk_pins()"
 148     function in the rom, and the USB clock and pins are manually
 149     configured.
 150 */
 151 /**************************************************************************/
 152 void usbHIDInit (void)
 153 {
 154   // Setup USB clock
 155   SCB_PDRUNCFG &= ~(SCB_PDSLEEPCFG_USBPAD_PD);        // Power-up USB PHY
 156   SCB_PDRUNCFG &= ~(SCB_PDSLEEPCFG_USBPLL_PD);        // Power-up USB PLL
 157
 158   SCB_USBPLLCLKSEL = SCB_USBPLLCLKSEL_SOURCE_MAINOSC; // Select PLL Input
 159   SCB_USBPLLCLKUEN = SCB_USBPLLCLKUEN_UPDATE;         // Update Clock Source
 160   SCB_USBPLLCLKUEN = SCB_USBPLLCLKUEN_DISABLE;        // Toggle Update Register
 161   SCB_USBPLLCLKUEN = SCB_USBPLLCLKUEN_UPDATE;
 162
 163   // Wait until the USB clock is updated
 164   while (!(SCB_USBPLLCLKUEN & SCB_USBPLLCLKUEN_UPDATE));
 165
 166   // Set USB clock to 48MHz (12MHz x 4)
 167   SCB_USBPLLCTRL = (SCB_USBPLLCTRL_MULT_4);
 168   while (!(SCB_USBPLLSTAT & SCB_USBPLLSTAT_LOCK));    // Wait Until PLL Locked
 169   SCB_USBCLKSEL = SCB_USBCLKSEL_SOURCE_USBPLLOUT;
 170
 171   // Set USB pin functions
 172   IOCON_PIO0_1 &= ~IOCON_PIO0_1_FUNC_MASK;
 173   IOCON_PIO0_1 |= IOCON_PIO0_1_FUNC_CLKOUT;           // CLK OUT
 174   IOCON_PIO0_3 &= ~IOCON_PIO0_3_FUNC_MASK;
 175   IOCON_PIO0_3 |= IOCON_PIO0_3_FUNC_USB_VBUS;         // VBus
 176   IOCON_PIO0_6 &= ~IOCON_PIO0_6_FUNC_MASK;
 177   IOCON_PIO0_6 |= IOCON_PIO0_6_FUNC_USB_CONNECT;      // Soft Connect
 178
 179   // Disable internal resistor on VBUS (0.3)
 180   gpioSetPullup(&IOCON_PIO0_3, gpioPullupMode_Inactive);
 181
 182   // HID Device Info
 183   volatile int n;
 184   HidDevInfo.idVendor = USB_VENDOR_ID;
 185   HidDevInfo.idProduct = USB_PROD_ID;
 186   HidDevInfo.bcdDevice = USB_DEVICE;
 187   HidDevInfo.StrDescPtr = (uint32_t)&USB_HIDStringDescriptor[0];
 188   HidDevInfo.InReportCount = sizeof(usbhid_out_t);
 189   HidDevInfo.OutReportCount = 1;
 190   HidDevInfo.SampleInterval = 0x20;
 191   HidDevInfo.InReport = usbHIDGetInReport;
 192   HidDevInfo.OutReport = usbHIDSetOutReport;
 193
 194   DeviceInfo.DevType = USB_DEVICE_CLASS_HUMAN_INTERFACE;
 195   DeviceInfo.DevDetailPtr = (uint32_t)&HidDevInfo;
 196
 197   /* Enable Timer32_1, IOCON, and USB blocks (for USB ROM driver) */
 198   SCB_SYSAHBCLKCTRL |= (SCB_SYSAHBCLKCTRL_CT32B1 | SCB_SYSAHBCLKCTRL_IOCON | SCB_SYSAHBCLKCTRL_USB_REG);
 199
 200   /* Use pll and pin init function in rom */
 201   /* Warning: This will also set the system clock to 48MHz! */
 202   // (*rom)->pUSBD->init_clk_pins();
 203
 204   /* insert a delay between clk init and usb init */
 205   for (n = 0; n < 75; n++) {__asm("nop");}
 206
 207   (*rom)->pUSBD->init(&DeviceInfo); /* USB Initialization */
 208   (*rom)->pUSBD->connect(true);     /* USB Connect */
 209 }
 210
 211 /**************************************************************************/
 212 /*!
 213     @brief Passes the USB interrupt to the internal ROM-based handler
 214 */
 215 /**************************************************************************/
 216 #ifdef CFG_USBHID
 217 void USB_IRQHandler()
 218 {
 219   (*rom)->pUSBD->isr();
 220 }
 221 #endif
 222