drivers/rf/chibi/chb_drvr.c

   1 /*******************************************************************
   2     Copyright (C) 2009 FreakLabs
   3     All rights reserved.
   4
   5     Redistribution and use in source and binary forms, with or without
   6     modification, are permitted provided that the following conditions
   7     are met:
   8
   9     1. Redistributions of source code must retain the above copyright
  10        notice, this list of conditions and the following disclaimer.
  11     2. Redistributions in binary form must reproduce the above copyright
  12        notice, this list of conditions and the following disclaimer in the
  13        documentation and/or other materials provided with the distribution.
  14     3. Neither the name of the the copyright holder nor the names of its contributors
  15        may be used to endorse or promote products derived from this software
  16        without specific prior written permission.
  17
  18     THIS SOFTWARE IS PROVIDED BY THE THE COPYRIGHT HOLDERS AND CONTRIBUTORS ``AS IS'' AND
  19     ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
  20     IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
  21     ARE DISCLAIMED.  IN NO EVENT SHALL THE INSTITUTE OR CONTRIBUTORS BE LIABLE
  22     FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
  23     DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
  24     OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  25     HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
  26     LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
  27     OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
  28     SUCH DAMAGE.
  29
  30     Originally written by Christopher Wang aka Akiba.
  31     Please post support questions to the FreakLabs forum.
  32
  33 *******************************************************************/
  34 #include <stdio.h>
  35 #include "chb.h"
  36 #include "chb_drvr.h"
  37 #include "chb_buf.h"
  38 #include "chb_spi.h"
  39 #include "chb_eeprom.h"
  40
  41 #include "core/systick/systick.h"
  42 #include "core/timer16/timer16.h"
  43
  44 // store string messages in flash rather than RAM
  45 const char chb_err_overflow[] = "BUFFER FULL. TOSSING INCOMING DATA\r\n";
  46 const char chb_err_init[] = "RADIO NOT INITIALIZED PROPERLY\r\n";
  47 /**************************************************************************/
  48 /*!
  49
  50 */
  51 /**************************************************************************/
  52 static U8 chb_get_state()
  53 {
  54     return chb_reg_read(TRX_STATUS) & 0x1f;
  55 }
  56
  57 /**************************************************************************/
  58 /*!
  59
  60 */
  61 /**************************************************************************/
  62 static U8 chb_get_status()
  63 {
  64     return chb_reg_read(TRX_STATE) >> CHB_TRAC_STATUS_POS;
  65 }
  66
  67 /**************************************************************************/
  68 /*!
  69     Cause a blocking delay for x microseconds
  70 */
  71 /**************************************************************************/
  72 static void chb_delay_us(U16 usec)
  73 {
  74   // Determine maximum delay using a 16 bit timer
  75   // ToDo: Move this to a macro or fixed value!
  76   uint32_t maxus = 0xFFFF / (CFG_CPU_CCLK / 1000000);
  77
  78   // Check if delay can be done in one operation
  79   if (usec <= maxus)
  80   {
  81     timer16DelayUS(0, usec);
  82     return;
  83   }
  84
  85   // Split delay into several steps (to stay within limit of 16-bit timer)
  86   do
  87   {
  88     if (usec >= maxus)
  89     {
  90       timer16DelayUS(0, maxus);
  91       usec -= maxus;
  92     }
  93     else
  94     {
  95       timer16DelayUS(0, usec);
  96       usec = 0;
  97     }
  98   } while (usec > 0);
  99 }
 100
 101 /**************************************************************************/
 102 /*!
 103
 104 */
 105 /**************************************************************************/
 106 void chb_reset()
 107 {
 108     CHB_RST_DISABLE();
 109     CHB_SLPTR_DISABLE();
 110
 111     // wait a bit while transceiver wakes up
 112     chb_delay_us(TIME_P_ON_TO_CLKM_AVAIL);
 113
 114     // reset the device
 115     CHB_RST_ENABLE();
 116     chb_delay_us(TIME_RST_PULSE_WIDTH);
 117     CHB_RST_DISABLE();
 118
 119     // check that we have the part number that we're expecting
 120     while (1)
 121     {
 122         // if you're stuck in this loop, that means that you're not reading
 123         // the version and part number register correctly. possible that version number
 124         // changes. if so, update version num in header file
 125         if ((chb_reg_read(VERSION_NUM) == CHB_AT86RF212_VER_NUM) && (chb_reg_read(PART_NUM) == CHB_AT86RF212_PART_NUM))
 126         {
 127             break;
 128         }
 129     }
 130 }
 131
 132 /**************************************************************************/
 133 /*!
 134
 135 */
 136 /**************************************************************************/
 137 U8 chb_reg_read(U8 addr)
 138 {
 139     U8 val = 0;
 140
 141     /* Add the register read command to the register address. */
 142     addr |= 0x80;
 143
 144     CHB_ENTER_CRIT();
 145     CHB_SPI_ENABLE();
 146
 147     /*Send Register address and read register content.*/
 148     val = chb_xfer_byte(addr);
 149     val = chb_xfer_byte(val);
 150
 151     CHB_SPI_DISABLE();
 152     CHB_LEAVE_CRIT();
 153
 154     return val;
 155 }
 156
 157 /**************************************************************************/
 158 /*!
 159
 160 */
 161 /**************************************************************************/
 162 U16 chb_reg_read16(U8 addr)
 163 {
 164     U8 i;
 165     U16 val = 0;
 166
 167     for (i=0; i<2; i++)
 168     {
 169         addr |= chb_reg_read(addr + i) << (8 * i);
 170     }
 171     return val;
 172 }
 173
 174 /**************************************************************************/
 175 /*!
 176
 177 */
 178 /**************************************************************************/
 179 void chb_reg_write(U8 addr, U8 val)
 180 {
 181     // U8 dummy;
 182
 183     /* Add the Register Write command to the address. */
 184     addr |= 0xC0;
 185
 186     CHB_ENTER_CRIT();
 187     CHB_SPI_ENABLE();
 188
 189     /*Send Register address and write register content.*/
 190     // dummy = chb_xfer_byte(addr);
 191     // dummy = chb_xfer_byte(val);
 192     chb_xfer_byte(addr);
 193     chb_xfer_byte(val);
 194
 195     CHB_SPI_DISABLE();
 196     CHB_LEAVE_CRIT();
 197 }
 198
 199 /**************************************************************************/
 200 /*!
 201
 202 */
 203 /**************************************************************************/
 204 void chb_reg_write16(U8 addr, U16 val)
 205 {
 206     U8 i;
 207
 208     for (i=0; i<2; i++)
 209     {
 210         chb_reg_write(addr + i, val >> (8 * i));
 211     }
 212 }
 213
 214 /**************************************************************************/
 215 /*!
 216
 217 */
 218 /**************************************************************************/
 219 void chb_reg_write64(U8 addr, U8 *val)
 220 {
 221     U8 i;
 222
 223     for (i=0; i<8; i++)
 224     {
 225         chb_reg_write(addr + i, *(val + i));
 226     }
 227 }
 228
 229 /**************************************************************************/
 230 /*!
 231
 232 */
 233 /**************************************************************************/
 234 void chb_reg_read_mod_write(U8 addr, U8 val, U8 mask)
 235 {
 236     U8 tmp;
 237
 238     tmp = chb_reg_read(addr);
 239     val &= mask;                // mask off stray bits from val
 240     tmp &= ~mask;               // mask off bits in reg val
 241     tmp |= val;                 // copy val into reg val
 242     chb_reg_write(addr, tmp);   // write back to reg
 243 }
 244
 245 /**************************************************************************/
 246 /*!
 247
 248 */
 249 /**************************************************************************/
 250 void chb_frame_write(U8 *hdr, U8 hdr_len, U8 *data, U8 data_len)
 251 {
 252     //U8 i, dummy;
 253     U8 i;
 254
 255     // dont allow transmission longer than max frame size
 256     if ((hdr_len + data_len) > 127)
 257     {
 258         return;
 259     }
 260
 261     // initiate spi transaction
 262     CHB_ENTER_CRIT();
 263     CHB_SPI_ENABLE();
 264
 265     // send fifo write command
 266     // dummy = chb_xfer_byte(CHB_SPI_CMD_FW);
 267     chb_xfer_byte(CHB_SPI_CMD_FW);
 268
 269     // write hdr contents to fifo
 270     for (i=0; i<hdr_len; i++)
 271     {
 272         // dummy = chb_xfer_byte(*hdr++);
 273         chb_xfer_byte(*hdr++);
 274     }
 275
 276     // write data contents to fifo
 277     for (i=0; i<data_len; i++)
 278     {
 279         // dummy = chb_xfer_byte(*data++);
 280         chb_xfer_byte(*data++);
 281     }
 282
 283     // terminate spi transaction
 284     CHB_SPI_DISABLE();
 285     CHB_LEAVE_CRIT();
 286 }
 287
 288 /**************************************************************************/
 289 /*!
 290
 291 */
 292 /**************************************************************************/
 293 static void chb_frame_read()
 294 {
 295     U8 i, len, data;
 296
 297     // CHB_ENTER_CRIT();
 298     CHB_SPI_ENABLE();
 299
 300     /*Send frame read command and read the length.*/
 301     chb_xfer_byte(CHB_SPI_CMD_FR);
 302     len = chb_xfer_byte(0);
 303
 304     /*Check for correct frame length.*/
 305     if ((len >= CHB_MIN_FRAME_LENGTH) && (len <= CHB_MAX_FRAME_LENGTH))
 306     {
 307         // check to see if there is room to write the frame in the buffer. if not, then drop it
 308         if (len < (CFG_CHIBI_BUFFERSIZE - chb_buf_get_len()))
 309         {
 310             chb_buf_write(len);
 311
 312             for (i=0; i<len; i++)
 313             {
 314                 data = chb_xfer_byte(0);
 315                 chb_buf_write(data);
 316             }
 317         }
 318         else
 319         {
 320             // we've overflowed the buffer. toss the data and do some housekeeping
 321             chb_pcb_t *pcb = chb_get_pcb();
 322
 323             // read out the data and throw it away
 324             for (i=0; i<len; i++)
 325             {
 326                 data = chb_xfer_byte(0);
 327             }
 328
 329             // Increment the overflow stat
 330             pcb->overflow++;
 331
 332             // print the error message
 333             printf(chb_err_overflow);
 334         }
 335     }
 336
 337     CHB_SPI_DISABLE();
 338     CHB_LEAVE_CRIT();
 339 }
 340
 341 /**************************************************************************/
 342 /*!
 343     Read directly from the SRAM on the radio. This is only used for debugging
 344     purposes.
 345 */
 346 /**************************************************************************/
 347 #ifdef CHB_DEBUG
 348 void chb_sram_read(U8 addr, U8 len, U8 *data)
 349 {
 350     U8 i, dummy;
 351
 352     CHB_ENTER_CRIT();
 353     CHB_SPI_ENABLE();
 354
 355     /*Send SRAM read command.*/
 356     dummy = chb_xfer_byte(CHB_SPI_CMD_SR);
 357
 358     /*Send address where to start reading.*/
 359     dummy = chb_xfer_byte(addr);
 360
 361     for (i=0; i<len; i++)
 362     {
 363         *data++ = chb_xfer_byte(0);
 364     }
 365
 366     CHB_SPI_DISABLE();
 367     CHB_LEAVE_CRIT();
 368 }
 369
 370 /**************************************************************************/
 371 /*!
 372
 373 */
 374 /**************************************************************************/
 375 void chb_sram_write(U8 addr, U8 len, U8 *data)
 376 {
 377     U8 i, dummy;
 378
 379     CHB_ENTER_CRIT();
 380     CHB_SPI_ENABLE();
 381
 382     /*Send SRAM write command.*/
 383     dummy = chb_xfer_byte(CHB_SPI_CMD_SW);
 384
 385     /*Send address where to start writing to.*/
 386     dummy = chb_xfer_byte(addr);
 387
 388     for (i=0; i<len; i++)
 389     {
 390         dummy = chb_xfer_byte(*data++);
 391     }
 392
 393     CHB_SPI_DISABLE();
 394     CHB_LEAVE_CRIT();
 395 }
 396 #endif
 397
 398 /**************************************************************************/
 399 /*!
 400     Set the channel mode, BPSK, OQPSK, etc...
 401 */
 402 /**************************************************************************/
 403 void chb_set_mode(U8 mode)
 404 {
 405     switch (mode)
 406     {
 407     case OQPSK_868MHZ:
 408         chb_reg_read_mod_write(TRX_CTRL_2, 0x08, 0x3f);                 // 802.15.4-2006, channel page 2, channel 0 (868 MHz, Europe)
 409         chb_reg_read_mod_write(RF_CTRL_0, CHB_OQPSK_TX_OFFSET, 0x3);    // this is according to table 7-16 in at86rf212 datasheet
 410         break;
 411     case OQPSK_915MHZ:
 412         chb_reg_read_mod_write(TRX_CTRL_2, 0x0c, 0x3f);                 // 802.15.4-2006, channel page 2, channels 1-10 (915 MHz, US)
 413         chb_reg_read_mod_write(RF_CTRL_0, CHB_OQPSK_TX_OFFSET, 0x3);    // this is according to table 7-16 in at86rf212 datasheet
 414         break;
 415     case OQPSK_780MHZ:
 416         chb_reg_read_mod_write(TRX_CTRL_2, 0x1c, 0x3f);                 // 802.15.4-2006, channel page 5, channel 0-3 (780 MHz, China)
 417         chb_reg_read_mod_write(RF_CTRL_0, CHB_OQPSK_TX_OFFSET, 0x3);    // this is according to table 7-16 in at86rf212 datasheet
 418         break;
 419     case BPSK40_915MHZ:
 420         chb_reg_read_mod_write(TRX_CTRL_2, 0x00, 0x3f);                 // 802.15.4-2006, BPSK, 40 kbps
 421         chb_reg_read_mod_write(RF_CTRL_0, CHB_BPSK_TX_OFFSET, 0x3);     // this is according to table 7-16 in at86rf212 datasheet
 422         break;
 423     case BPSK20_868MHZ:
 424         chb_reg_read_mod_write(TRX_CTRL_2, 0x00, 0x3f);                 // 802.15.4-2006, BPSK, 20 kbps
 425         chb_reg_read_mod_write(RF_CTRL_0, CHB_BPSK_TX_OFFSET, 0x3);     // this is according to table 7-16 in at86rf212 datasheet
 426         break;
 427     }
 428 }
 429
 430 /**************************************************************************/
 431 /*!
 432
 433 */
 434 /**************************************************************************/
 435 U8 chb_set_channel(U8 channel)
 436 {
 437     U8 state;
 438
 439 #if (CHB_CHINA == 1)
 440
 441     // this if for China only which uses a 780 MHz frequency band
 442     if ((chb_reg_read(TRX_CTRL2) & 0x3f) != 0x1c)
 443     {
 444         chb_reg_read_mod_write(TRX_CTRL2, 0x1c, 0x3f);
 445     }
 446
 447     if (channel > 3)
 448     {
 449         channel = 0;
 450     }
 451
 452     channel = (channel << 1) + 11;
 453
 454     chb_reg_read_mod_write(CC_CTRL_1, 0x4, 0x7);                // set 769 MHz base frequency for China
 455     chb_reg_write(CC_CTRL_0, channel);                          // set the center frequency for the channel
 456
 457 #else
 458     //if (channel == 0)
 459     //{
 460     //    // Channel 0 is for European use only. make sure we are using channel page 2,
 461     //    // channel 0 settings for 100 kbps
 462     //    if ((chb_reg_read(TRX_CTRL_2) & 0x3f) != 0x08)
 463     //    {
 464     //        chb_reg_read_mod_write(TRX_CTRL_2, 0x08, 0x3f);
 465     //    }
 466     //}
 467     //else if (channel > 10)
 468     //{
 469     //    // if the channel is out of bounds for page 2, then default to channel 1 and
 470     //    // assume we're on the US frequency of 915 MHz
 471     //    channel = 1;
 472     //    if ((chb_reg_read(TRX_CTRL_2) & 0x3f) != 0x0c)
 473     //    {
 474     //        chb_reg_read_mod_write(TRX_CTRL_2, 0x0c, 0x3f);
 475     //    }
 476     //}
 477     //else
 478     //{
 479     //    // Channels 1-10 are for US frequencies of 915 MHz
 480     //    if ((chb_reg_read(TRX_CTRL_2) & 0x3f) != 0x0c)
 481     //    {
 482     //        chb_reg_read_mod_write(TRX_CTRL_2, 0x0c, 0x3f);
 483     //    }
 484     //}
 485
 486     chb_reg_read_mod_write(PHY_CC_CCA, channel, 0x1f);
 487 #endif
 488
 489     // add a delay to allow the PLL to lock if in active mode.
 490     state = chb_get_state();
 491     if ((state == RX_ON) || (state == PLL_ON))
 492     {
 493         chb_delay_us(TIME_PLL_LOCK_TIME);
 494     }
 495
 496     return ((chb_reg_read(PHY_CC_CCA) & 0x1f) == channel) ? RADIO_SUCCESS : RADIO_TIMED_OUT;
 497 }
 498
 499 /**************************************************************************/
 500 /*!
 501     Set the power level
 502 */
 503 /**************************************************************************/
 504 void chb_set_pwr(U8 val)
 505 {
 506     chb_reg_write(PHY_TX_PWR, val);
 507 }
 508
 509 /**************************************************************************/
 510 /*!
 511     Set the TX/RX state machine state. Some manual manipulation is required
 512     for certain operations. Check the datasheet for more details on the state
 513     machine and manipulations.
 514 */
 515 /**************************************************************************/
 516 U8 chb_set_state(U8 state)
 517 {
 518     U8 curr_state, delay;
 519
 520     // if we're sleeping then don't allow transition
 521     if (gpioGetValue(CHB_SLPTRPORT, CHB_SLPTRPIN))
 522     {
 523         return RADIO_WRONG_STATE;
 524     }
 525
 526     // if we're in a transition state, wait for the state to become stable
 527     curr_state = chb_get_state();
 528     if ((curr_state == BUSY_TX_ARET) || (curr_state == BUSY_RX_AACK) || (curr_state == BUSY_RX) || (curr_state == BUSY_TX))
 529     {
 530         while (chb_get_state() == curr_state);
 531     }
 532
 533     // At this point it is clear that the requested new_state is:
 534     // TRX_OFF, RX_ON, PLL_ON, RX_AACK_ON or TX_ARET_ON.
 535     // we need to handle some special cases before we transition to the new state
 536     switch (state)
 537     {
 538     case TRX_OFF:
 539         /* Go to TRX_OFF from any state. */
 540         CHB_SLPTR_DISABLE();
 541         chb_reg_read_mod_write(TRX_STATE, CMD_FORCE_TRX_OFF, 0x1f);
 542         chb_delay_us(TIME_ALL_STATES_TRX_OFF);
 543         break;
 544
 545     case TX_ARET_ON:
 546         if (curr_state == RX_AACK_ON)
 547         {
 548             /* First do intermediate state transition to PLL_ON, then to TX_ARET_ON. */
 549             chb_reg_read_mod_write(TRX_STATE, CMD_PLL_ON, 0x1f);
 550             chb_delay_us(TIME_RX_ON_PLL_ON);
 551         }
 552         break;
 553
 554     case RX_AACK_ON:
 555         if (curr_state == TX_ARET_ON)
 556         {
 557             /* First do intermediate state transition to RX_ON, then to RX_AACK_ON. */
 558             chb_reg_read_mod_write(TRX_STATE, CMD_PLL_ON, 0x1f);
 559             chb_delay_us(TIME_RX_ON_PLL_ON);
 560         }
 561         break;
 562     }
 563
 564     /* Now we're okay to transition to any new state. */
 565     chb_reg_read_mod_write(TRX_STATE, state, 0x1f);
 566
 567     /* When the PLL is active most states can be reached in 1us. However, from */
 568     /* TRX_OFF the PLL needs time to activate. */
 569     delay = (curr_state == TRX_OFF) ? TIME_TRX_OFF_PLL_ON : TIME_RX_ON_PLL_ON;
 570     chb_delay_us(delay);
 571
 572     if (chb_get_state() == state)
 573     {
 574         return RADIO_SUCCESS;
 575     }
 576     return RADIO_TIMED_OUT;
 577 }
 578
 579 /**************************************************************************/
 580 /*!
 581
 582 */
 583 /**************************************************************************/
 584 void chb_set_ieee_addr(U8 *addr)
 585 {
 586     chb_eeprom_write(CFG_EEPROM_CHIBI_IEEEADDR, addr, 8);
 587     chb_reg_write64(IEEE_ADDR_0, addr);
 588 }
 589
 590 /**************************************************************************/
 591 /*!
 592
 593 */
 594 /**************************************************************************/
 595 void chb_get_ieee_addr(U8 *addr)
 596 {
 597     chb_eeprom_read(CFG_EEPROM_CHIBI_IEEEADDR, addr, 8);
 598 }
 599
 600 /**************************************************************************/
 601 /*!
 602
 603 */
 604 /**************************************************************************/
 605 void chb_set_short_addr(U16 addr)
 606 {
 607     U8 *addr_ptr = (U8 *)&addr;
 608     chb_pcb_t *pcb = chb_get_pcb();
 609
 610     chb_eeprom_write(CFG_EEPROM_CHIBI_SHORTADDR, addr_ptr, 2);
 611     chb_reg_write16(SHORT_ADDR_0, addr);
 612     pcb->src_addr = addr;
 613 }
 614
 615 /**************************************************************************/
 616 /*!
 617
 618 */
 619 /**************************************************************************/
 620 U16 chb_get_short_addr()
 621 {
 622     int16_t addr;
 623
 624     chb_eeprom_read(CFG_EEPROM_CHIBI_SHORTADDR, (uint8_t*)&addr, 2);
 625     return addr;
 626 }
 627 /**************************************************************************/
 628 /*!
 629     Set the high gain mode pin for the CC1190
 630 */
 631 /**************************************************************************/
 632 #if (CHB_CC1190_PRESENT)
 633 void chb_set_hgm(U8 enb)
 634 {
 635     if (enb)
 636     {
 637         gpioSetValue(CHB_CC1190_HGM_PORT, CHB_CC1190_HGM_PIN, 1);
 638     }
 639     else
 640     {
 641         gpioSetValue(CHB_CC1190_HGM_PORT, CHB_CC1190_HGM_PIN, 0);
 642     }
 643 }
 644 #endif
 645
 646 /**************************************************************************/
 647 /*!
 648     Load the data into the fifo, initiate a transmission attempt,
 649     and return the status of the transmission attempt.
 650 */
 651 /**************************************************************************/
 652 U8 chb_tx(U8 *hdr, U8 *data, U8 len)
 653 {
 654     U8 state = chb_get_state();
 655     chb_pcb_t *pcb = chb_get_pcb();
 656
 657     if ((state == BUSY_TX) || (state == BUSY_TX_ARET))
 658     {
 659         return RADIO_WRONG_STATE;
 660     }
 661
 662     // TODO: check why we need to transition to the off state before we go to tx_aret_on
 663     chb_set_state(TRX_OFF);
 664     chb_set_state(TX_ARET_ON);
 665
 666     // TODO: try and start the frame transmission by writing TX_START command instead of toggling
 667     // sleep pin...i just feel like it's kind of weird...
 668
 669     // write frame to buffer. first write header into buffer (add 1 for len byte), then data.
 670     chb_frame_write(hdr, CHB_HDR_SZ + 1, data, len);
 671
 672     //Do frame transmission
 673     chb_reg_read_mod_write(TRX_STATE, CMD_TX_START, 0x1F);
 674
 675     // wait for the transmission to end, signalled by the TRX END flag
 676     while (!pcb->tx_end);
 677     pcb->tx_end = false;
 678
 679     // check the status of the transmission
 680     return chb_get_status();
 681 }
 682
 683 /**************************************************************************/
 684 /*!
 685
 686 */
 687 /**************************************************************************/
 688 static void chb_radio_init()
 689 {
 690     U8 ieee_addr[8];
 691
 692     // reset chip
 693     chb_reset();
 694
 695     // disable intps while we config the radio
 696     chb_reg_write(IRQ_MASK, 0);
 697
 698     // force transceiver off while we configure the intps
 699     chb_reg_read_mod_write(TRX_STATE, CMD_FORCE_TRX_OFF, 0x1F);
 700
 701     // make sure the transceiver is in the off state before proceeding
 702     while ((chb_reg_read(TRX_STATUS) & 0x1f) != TRX_OFF);
 703
 704     // set radio cfg parameters
 705     // **note** uncomment if these will be set to something other than default
 706     //chb_reg_read_mod_write(XAH_CTRL_0, CHB_MAX_FRAME_RETRIES << CHB_MAX_FRAME_RETRIES_POS, 0xF << CHB_MAX_FRAME_RETRIES_POS);
 707     //chb_reg_read_mod_write(XAH_CTRL_0, CHB_MAX_CSMA_RETRIES << CHB_MAX_CSMA_RETIRES_POS, 0x7 << CHB_MAX_CSMA_RETIRES_POS);
 708     //chb_reg_read_mod_write(CSMA_SEED_1, CHB_CSMA_SEED1 << CHB_CSMA_SEED1_POS, 0x7 << CHB_CSMA_SEED1_POS);
 709     //chb_ret_write(CSMA_SEED0, CHB_CSMA_SEED0);
 710     //chb_reg_read_mod_write(PHY_CC_CCA, CHB_CCA_MODE << CHB_CCA_MODE_POS,0x3 << CHB_CCA_MODE_POS);
 711     //chb_reg_write(CCA_THRES, CHB_CCA_ED_THRES);
 712
 713     // set frame version that we'll accept
 714     chb_reg_read_mod_write(CSMA_SEED_1, CHB_FRM_VER << CHB_FVN_POS, 3 << CHB_FVN_POS);
 715
 716     // set interrupt mask
 717     // re-enable intps while we config the radio
 718     chb_reg_write(IRQ_MASK, (1<<IRQ_RX_START) | (1<<IRQ_TRX_END));
 719
 720     #if (CFG_CHIBI_PROMISCUOUS == 0)
 721       // set autocrc mode
 722       chb_reg_read_mod_write(TRX_CTRL_1, 1 << CHB_AUTO_CRC_POS, 1 << CHB_AUTO_CRC_POS);
 723     #endif
 724     // set up default phy modulation, data rate and power (Ex. OQPSK, 100 kbps, 868 MHz, 3dBm)
 725     chb_set_mode(CFG_CHIBI_MODE);       // Defined in projectconfig.h
 726     chb_set_pwr(CFG_CHIBI_POWER);       // Defined in projectconfig.h
 727     chb_set_channel(CFG_CHIBI_CHANNEL); // Defined in projectconfig.h
 728
 729     // set fsm state
 730     // put trx in rx auto ack mode
 731     chb_set_state(RX_STATE);
 732
 733     // set pan ID
 734     chb_reg_write16(PAN_ID_0, CFG_CHIBI_PANID); // Defined in projectconfig.h
 735
 736     // set short addr
 737     // NOTE: Possibly get this from EEPROM
 738     chb_reg_write16(SHORT_ADDR_0, chb_get_short_addr());
 739
 740     // set long addr
 741     // NOTE: Possibly get this from EEPROM
 742     chb_get_ieee_addr(ieee_addr);
 743     chb_reg_write64(IEEE_ADDR_0, ieee_addr);
 744
 745 #if (CHB_CC1190_PRESENT)
 746     // set high gain mode pin to output and init to zero
 747     gpioSetDir (CHB_CC1190_HGM_PORT, CHB_CC1190_HGM_PIN, 1);
 748     gpioSetPullup (&CHB_CC1190_HGM_IOCONREG, gpioPullupMode_Inactive);
 749     gpioSetValue (CHB_CC1190_HGM_PORT, CHB_CC1190_HGM_PIN, 0);
 750
 751     // set external power amp on AT86RF212
 752     chb_reg_read_mod_write(TRX_CTRL_1, 1<<CHB_PA_EXT_EN_POS, 1<<CHB_PA_EXT_EN_POS);
 753
 754     // set power to lowest level possible
 755     chb_set_pwr(0xd);   // set to -11 dBm
 756 #endif
 757
 758     // set interrupt/gpio pin to input
 759     gpioSetDir (CHB_EINTPORT, CHB_EINTPIN, 0);
 760
 761     // set internal resistor on EINT pin to inactive
 762     gpioSetPullup (&CHB_EINTPIN_IOCONREG, gpioPullupMode_Inactive);
 763
 764     // configure pin for interrupt
 765     gpioSetInterrupt (CHB_EINTPORT,
 766                       CHB_EINTPIN,
 767                       gpioInterruptSense_Edge,        // Edge-sensitive
 768                       gpioInterruptEdge_Single,       // Single edge
 769                       gpioInterruptEvent_ActiveLow);  // High triggers interrupt
 770
 771     // enable interrupt
 772     gpioIntEnable (CHB_EINTPORT,
 773                    CHB_EINTPIN);
 774
 775     if (chb_get_state() != RX_STATE)
 776     {
 777         // ERROR occurred initializing the radio. Print out error message.
 778         printf(chb_err_init);
 779     }
 780 }
 781
 782 /**************************************************************************/
 783 /*!
 784
 785 */
 786 /**************************************************************************/
 787 void chb_drvr_init()
 788 {
 789     // ToDo: Make sure gpioInit has been called
 790     // ToDo: Make sure CT32B0 has been initialised and enabled
 791
 792     // config SPI for at86rf230 access
 793     chb_spi_init();
 794
 795     // Setup 16-bit timer 0 (used for us delays)
 796     timer16Init(0, 0xFFFF);
 797     timer16Enable(0);
 798
 799     // Set sleep and reset as output
 800     gpioSetDir(CHB_SLPTRPORT, CHB_SLPTRPIN, 1);
 801     gpioSetDir(CHB_RSTPORT, CHB_RSTPIN, 1);
 802
 803     // configure IOs
 804     gpioSetValue(CHB_SLPTRPORT, CHB_SLPTRPIN, 1);  // Set sleep high
 805     gpioSetValue(CHB_RSTPORT, CHB_RSTPIN, 1);      // Set reset high
 806
 807     // Set internal resistors
 808     gpioSetPullup (&CHB_SLPTRPIN_IOCONREG, gpioPullupMode_Inactive);
 809     gpioSetPullup (&CHB_RSTPIN_IOCONREG, gpioPullupMode_Inactive);
 810
 811     // config radio
 812     chb_radio_init();
 813 }
 814
 815 /**************************************************************************/
 816 /*!
 817     Enable or disable the radio's sleep mode.
 818 */
 819 /**************************************************************************/
 820 void chb_sleep(U8 enb)
 821 {
 822   if (enb)
 823   {
 824     // first we need to go to TRX OFF state
 825     chb_set_state(TRX_OFF);
 826
 827     // set the SLPTR pin
 828     // CHB_SLPTR_PORT |= _BV(CHB_SLPTR_PIN);
 829     CHB_SLPTR_ENABLE();
 830   }
 831   else
 832   {
 833     // make sure the SLPTR pin is low first
 834     // CHB_SLPTR_PORT &= ~(_BV(CHB_SLPTR_PIN));
 835     CHB_SLPTR_DISABLE();
 836
 837     // we need to allow some time for the PLL to lock
 838     chb_delay_us(TIME_SLEEP_TO_TRX_OFF);
 839
 840     // Turn the transceiver back on
 841     chb_set_state(RX_STATE);
 842   }
 843 }
 844 /**************************************************************************/
 845 /*!
 846
 847 */
 848 /**************************************************************************/
 849 void chb_ISR_Handler (void)
 850 {
 851     // U8 dummy, state, intp_src = 0;
 852     U8 state, intp_src = 0;
 853     chb_pcb_t *pcb = chb_get_pcb();
 854
 855     CHB_ENTER_CRIT();
 856
 857     /*Read Interrupt source.*/
 858     CHB_SPI_ENABLE();
 859
 860     /*Send Register address and read register content.*/
 861     // dummy = chb_xfer_byte(IRQ_STATUS | CHB_SPI_CMD_RR);
 862     chb_xfer_byte(IRQ_STATUS | CHB_SPI_CMD_RR);
 863     intp_src = chb_xfer_byte(0);
 864
 865     CHB_SPI_DISABLE();
 866
 867     while (intp_src)
 868     {
 869         /*Handle the incomming interrupt. Prioritized.*/
 870         if ((intp_src & CHB_IRQ_RX_START_MASK))
 871         {
 872             intp_src &= ~CHB_IRQ_RX_START_MASK;
 873         }
 874         else if (intp_src & CHB_IRQ_TRX_END_MASK)
 875         {
 876             state = chb_get_state();
 877
 878             if ((state == RX_ON) || (state == RX_AACK_ON) || (state == BUSY_RX_AACK))
 879             {
 880                 // get the ed measurement
 881                 pcb->ed = chb_reg_read(PHY_ED_LEVEL);
 882
 883                 // get the crc
 884                 pcb->crc = (chb_reg_read(PHY_RSSI) & (1<<7)) ? 1 : 0;
 885
 886                 // if the crc is not valid, then do not read the frame and set the rx flag
 887                 if (pcb->crc)
 888                 {
 889                     // get the data
 890                     chb_frame_read();
 891                     pcb->rcvd_xfers++;
 892                     pcb->data_rcv = true;
 893                 }
 894             }
 895             else
 896             {
 897                 pcb->tx_end = true;
 898             }
 899             intp_src &= ~CHB_IRQ_TRX_END_MASK;
 900             while (chb_set_state(RX_STATE) != RADIO_SUCCESS);
 901         }
 902         else if (intp_src & CHB_IRQ_TRX_UR_MASK)
 903         {
 904             intp_src &= ~CHB_IRQ_TRX_UR_MASK;
 905             pcb->underrun++;
 906         }
 907         else if (intp_src & CHB_IRQ_PLL_UNLOCK_MASK)
 908         {
 909             intp_src &= ~CHB_IRQ_PLL_UNLOCK_MASK;
 910         }
 911         else if (intp_src & CHB_IRQ_PLL_LOCK_MASK)
 912         {
 913             intp_src &= ~CHB_IRQ_PLL_LOCK_MASK;
 914         }
 915         else if (intp_src & CHB_IRQ_BAT_LOW_MASK)
 916         {
 917             intp_src &= ~CHB_IRQ_BAT_LOW_MASK;
 918             pcb->battlow++;
 919         }
 920         else
 921         {
 922         }
 923     }
 924     CHB_LEAVE_CRIT();
 925 }