-# generated by Slic3r 1.2.9 on Mon May 9 21:40:16 2016
+# generated by Slic3r 1.2.9 on Fri May 13 17:04:53 2016
-[filament:LULZBOT PLA]
-bed_temperature = 50
-bridge_fan_speed = 100
+[filament:LULZBOT ABS fine]
+bed_temperature = 100
+bridge_fan_speed = 0
cooling = 1
disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 2.89
-first_layer_bed_temperature = 55
-first_layer_temperature = 190
-max_fan_speed = 100
-min_fan_speed = 35
-min_print_speed = 25
-slowdown_below_layer_time = 25
-temperature = 185
+first_layer_bed_temperature = 100
+first_layer_temperature = 250
+max_fan_speed = 0
+min_fan_speed = 0
+min_print_speed = 15
+slowdown_below_layer_time = 20
+temperature = 240
[filament:MendelPro ABS]
bed_temperature = 0
slowdown_below_layer_time = 30
temperature = 245
+[filament:MendelPro Holz]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 1
+disable_fan_first_layers = 1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FFFFFF
+filament_diameter = 1.7
+first_layer_bed_temperature = 55
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 50
+min_print_speed = 5
+slowdown_below_layer_time = 30
+temperature = 185
+
[filament:MendelPro PLA]
bed_temperature = 50
bridge_fan_speed = 100
slowdown_below_layer_time = 15
temperature = 185
-[filament:prusa i3 ABS black]
-bed_temperature = 0
+[filament:prusa i3 PLA black fine]
+bed_temperature = 50
bridge_fan_speed = 100
-cooling = 0
-disable_fan_first_layers = 2
+cooling = 1
+disable_fan_first_layers = 1
extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 60
+filament_colour = #FF0000
+filament_diameter = 2.9
+first_layer_bed_temperature = 50
+first_layer_temperature = 200
+max_fan_speed = 100
+min_fan_speed = 100
+min_print_speed = 5
+slowdown_below_layer_time = 15
+temperature = 200
+
+[filament:prusa i3 PLA igus]
+bed_temperature = 50
+bridge_fan_speed = 100
+cooling = 0
+disable_fan_first_layers = 1
+extrusion_multiplier = 0.9
fan_always_on = 0
fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.8
-first_layer_bed_temperature = 0
+filament_colour = #D0C9B0
+filament_diameter = 2.9
+first_layer_bed_temperature = 50
first_layer_temperature = 250
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
slowdown_below_layer_time = 15
-temperature = 245
+temperature = 250
-[filament:prusa i3 PLA klar orange]
+[filament:prusa i3 PLA rot]
bed_temperature = 50
bridge_fan_speed = 100
cooling = 1
-disable_fan_first_layers = 2
+disable_fan_first_layers = 1
extrusion_multiplier = 1
fan_always_on = 1
fan_below_layer_time = 60
-filament_colour = #FFFFFF
-filament_diameter = 2.6
+filament_colour = #FF0000
+filament_diameter = 2.9
first_layer_bed_temperature = 50
-first_layer_temperature = 190
+first_layer_temperature = 200
max_fan_speed = 100
min_fan_speed = 35
min_print_speed = 5
temperature = 200
[presets]
-filament = TinyBoy PLA.ini
-print = TinyBoy.ini
-printer = prusa i3.ini
+filament = LULZBOT ABS fine.ini
+print = prusa i3 100.ini
+printer = LULZBOT ABS fine.ini
-[print:LULZBOT]
-avoid_crossing_perimeters = 0
-bottom_solid_layers = 3
-bridge_acceleration = 2000
-bridge_flow_ratio = 1
-bridge_speed = 72
+[print:LULZBOT ABS fine ]
+avoid_crossing_perimeters = 1
+bottom_solid_layers = 2
+bridge_acceleration = 1000
+bridge_flow_ratio = 1.1
+bridge_speed = 40
brim_width = 0
complete_objects = 0
-default_acceleration = 2000
+default_acceleration = 900
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 45
+external_perimeter_speed = 30
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
-extrusion_width = 0.42
-fill_angle = 45
-fill_density = 20%
-fill_pattern = rectilinear
-first_layer_acceleration = 2000
-first_layer_extrusion_width = 0.53
-first_layer_height = 0.2
-first_layer_speed = 75%
-gap_fill_speed = 55
+extrusion_width = 0.37
+fill_angle = 35
+fill_density = 30%
+fill_pattern = line
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0.37
+first_layer_height = 120%
+first_layer_speed = 85%
+gap_fill_speed = 45
gcode_comments = 0
-infill_acceleration = 2000
-infill_every_layers = 1
+infill_acceleration = 1400
+infill_every_layers = 2
infill_extruder = 1
-infill_extrusion_width = 0.68
+infill_extrusion_width = 0.6
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
-infill_speed = 80
+infill_speed = 70
interface_shells = 0
-layer_height = 0.2
+layer_height = 0.14
max_print_speed = 80
max_volumetric_speed = 0
min_skirt_length = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
-perimeter_acceleration = 1200
+perimeter_acceleration = 900
perimeter_extruder = 1
-perimeter_extrusion_width = 0.38
-perimeter_speed = 75
-perimeters = 2
+perimeter_extrusion_width = 0.34
+perimeter_speed = 40
+perimeters = 4
post_process =
raft_layers = 0
-resolution = 0.001
+resolution = 0
seam_position = aligned
skirt_distance = 6
skirt_height = 1
-skirts = 3
-small_perimeter_speed = 50
-solid_infill_below_area = 90
+skirts = 2
+small_perimeter_speed = 30
+solid_infill_below_area = 30
solid_infill_every_layers = 0
solid_infill_extruder = 1
-solid_infill_extrusion_width = 0.5
-solid_infill_speed = 75
+solid_infill_extrusion_width = 0
+solid_infill_speed = 60
spiral_vase = 0
standby_temperature_delta = -5
support_material = 0
support_material_threshold = 45
thin_walls = 1
threads = 2
-top_infill_extrusion_width = 0.4
-top_solid_infill_speed = 60
-top_solid_layers = 3
-travel_speed = 160
+top_infill_extrusion_width = 0.35
+top_solid_infill_speed = 80%
+top_solid_layers = 4
+travel_speed = 80
xy_size_compensation = 0
[print:MendelPro]
extruder_clearance_radius = 20
extrusion_width = 0
fill_angle = 45
-fill_density = 20%
+fill_density = 15%
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_extrusion_width = 150%
travel_speed = 100
xy_size_compensation = 0
+[print:prusa i3 100]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 3
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 10
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 20%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 110%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.1
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 1
+notes =
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 3
+post_process =
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 6
+skirt_height = 1
+skirts = 3
+small_perimeter_speed = 10
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 5
+support_material_speed = 0
+support_material_threshold = 40
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 10
+top_solid_layers = 3
+travel_speed = 100
+xy_size_compensation = 0
+
+[print:prusa i3 100 testtesttest]
+avoid_crossing_perimeters = 0
+bottom_solid_layers = 0
+bridge_acceleration = 0
+bridge_flow_ratio = 1
+bridge_speed = 40
+brim_width = 0
+complete_objects = 0
+default_acceleration = 0
+dont_support_bridges = 1
+external_fill_pattern = rectilinear
+external_perimeter_extrusion_width = 0
+external_perimeter_speed = 10
+external_perimeters_first = 0
+extra_perimeters = 1
+extruder_clearance_height = 20
+extruder_clearance_radius = 20
+extrusion_width = 0
+fill_angle = 45
+fill_density = 0%
+fill_pattern = rectilinear
+first_layer_acceleration = 0
+first_layer_extrusion_width = 0
+first_layer_height = 0.2
+first_layer_speed = 10
+gap_fill_speed = 10
+gcode_comments = 0
+infill_acceleration = 0
+infill_every_layers = 1
+infill_extruder = 1
+infill_extrusion_width = 110%
+infill_first = 0
+infill_only_where_needed = 0
+infill_overlap = 15%
+infill_speed = 0
+interface_shells = 0
+layer_height = 0.1
+max_print_speed = 80
+max_volumetric_speed = 0
+min_skirt_length = 1
+notes =
+only_retract_when_crossing_perimeters = 1
+ooze_prevention = 0
+output_filename_format = [input_filename_base].gcode
+overhangs = 1
+perimeter_acceleration = 0
+perimeter_extruder = 1
+perimeter_extrusion_width = 0
+perimeter_speed = 0
+perimeters = 1
+post_process =
+raft_layers = 0
+resolution = 0
+seam_position = aligned
+skirt_distance = 1
+skirt_height = 1
+skirts = 1
+small_perimeter_speed = 10
+solid_infill_below_area = 70
+solid_infill_every_layers = 0
+solid_infill_extruder = 1
+solid_infill_extrusion_width = 0
+solid_infill_speed = 0
+spiral_vase = 0
+standby_temperature_delta = -5
+support_material = 0
+support_material_angle = 0
+support_material_contact_distance = 0.2
+support_material_enforce_layers = 0
+support_material_extruder = 1
+support_material_extrusion_width = 0
+support_material_interface_extruder = 1
+support_material_interface_layers = 2
+support_material_interface_spacing = 0
+support_material_interface_speed = 100%
+support_material_pattern = rectilinear
+support_material_spacing = 5
+support_material_speed = 0
+support_material_threshold = 40
+thin_walls = 1
+threads = 2
+top_infill_extrusion_width = 0
+top_solid_infill_speed = 10
+top_solid_layers = 0
+travel_speed = 100
+xy_size_compensation = 0
+
[print:prusa i3 250]
avoid_crossing_perimeters = 0
bottom_solid_layers = 3
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_flow_ratio = 1
-bridge_speed = 40
+bridge_speed = 60
brim_width = 0
complete_objects = 0
default_acceleration = 0
dont_support_bridges = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
-external_perimeter_speed = 10
+external_perimeter_speed = 20
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
first_layer_acceleration = 0
first_layer_extrusion_width = 0
first_layer_height = 0.2
-first_layer_speed = 15
+first_layer_speed = 10
gap_fill_speed = 10
gcode_comments = 0
infill_acceleration = 0
travel_speed = 100
xy_size_compensation = 0
-[printer:LULZBOT]
-bed_shape = 0x0,300x0,300x300,0x300
+[printer:LULZBOT ABS fine]
+bed_shape = 0x0,298x0,298x275,0x275
before_layer_gcode =
-end_gcode = M400 ; \nM104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200\nG28 X0 ; home X axis\nM84 ; disable motors
+end_gcode = M104 S0 ; turn off nozzle temperature\nM140 S0 ; turn off bed temperature\nG1 Y200 ;\nG28 X0 ; home X axis\nM84 ; disable motors
extruder_offset = 0x0
gcode_flavor = reprap
layer_gcode =
-nozzle_diameter = 0.5
+nozzle_diameter = 0.35
octoprint_apikey =
octoprint_host =
pressure_advance = 0
retract_before_travel = 2
retract_layer_change = 1
-retract_length = 1.9
+retract_length = 1.75
retract_length_toolchange = 3
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
-retract_speed = 30
+retract_speed = 20
start_gcode = G28 ; home all axes
toolchange_gcode =
use_firmware_retraction = 0
projects / stratum0-wiki.git / commitdiff