projectconfig.h

   1 /**************************************************************************/
   2 /*!
   3     @file     projectconfig.h
   4     @author   K. Townsend (microBuilder.eu)
   5
   6     @section LICENSE
   7
   8     Software License Agreement (BSD License)
   9
  10     Copyright (c) 2012, microBuilder SARL
  11     All rights reserved.
  12
  13     Redistribution and use in source and binary forms, with or without
  14     modification, are permitted provided that the following conditions are met:
  15     1. Redistributions of source code must retain the above copyright
  16     notice, this list of conditions and the following disclaimer.
  17     2. Redistributions in binary form must reproduce the above copyright
  18     notice, this list of conditions and the following disclaimer in the
  19     documentation and/or other materials provided with the distribution.
  20     3. Neither the name of the copyright holders nor the
  21     names of its contributors may be used to endorse or promote products
  22     derived from this software without specific prior written permission.
  23
  24     THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY
  25     EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
  26     WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  27     DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY
  28     DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  29     (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
  30     LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
  31     ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
  32     (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
  33     SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  34 */
  35 /**************************************************************************/
  36
  37 #ifndef _PROJECTCONFIG_H_
  38 #define _PROJECTCONFIG_H_
  39
  40 #include "lpc134x.h"
  41 #include "sysdefs.h"
  42
  43 /*=========================================================================
  44     BOARD SELECTION
  45
  46     Because several boards use this code library with sometimes slightly
  47     different pin configuration, you will need to specify which board you
  48     are using by enabling one of the following definitions. The code base
  49     will then try to configure itself accordingly for that board.
  50
  51     CFG_BRD_LPC1343_REFDESIGN
  52     =========================
  53
  54         microBuilder.eu LPC1343 Reference Design base board with
  55         on-board peripherals initialised (EEPROM, USB or UART CLI, etc.)
  56
  57                 This is the recommended starting point for new development
  58                 since it makes it easy to send printf output to USB CDC, access
  59                 the on-board EEPROM, etc.
  60
  61     CFG_BRD_LPC1343_REFDESIGN_MINIMAL
  62     =================================
  63
  64         microBuilder.eu LPC1343 Reference Design base board with
  65         only the most common peripherals initialised by default.
  66
  67         Results in smallest code since EEPROM, USB, etc., are not
  68         initialised on startup.  By default, only the following
  69         peripherals are initialised by systemInit():
  70
  71               - CPU (Configures the PLL, etc.)
  72               - GPIO
  73               - SysTick Timer
  74               - UART (with printf support) *
  75
  76         * Can be removed to save 0.8kb in debug and 0.3 kb in
  77         release. Comment out 'CFG_PRINTF_UART' to disable it.
  78
  79         The code size can be further reduced by several KB by removing
  80         any IRQ Handlers that are not used.  The I2C IRQHandler, for
  81         example, uses ~1KB of flash in debug and ~400KB in release mode,
  82         but because it is referenced in the startup code it is always
  83         included even if I2C is never used in the project.
  84
  85         Other IRQ Handlers that you might be able to comment out
  86         to save some space are:
  87
  88         IRQ Handler               Debug   Release
  89         ------------------------- ------  -------
  90         I2C_IRQHandler            1160 b    400 b
  91         SSP_IRQHandler             160 b     76 b
  92         UART_IRQHandler            246 b    116 b
  93         WAKEUP_IRQHandler          160 b    100 b
  94         WDT_IRQHandler              50 b     28 b
  95
  96     CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
  97     ====================================
  98
  99         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with USB enabled
 100         for the CLI interface.
 101
 102     CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 103     =====================================
 104
 105         microBuilder.eu/Adafruit Stand-Alone "Smart LCD" with UART enabled
 106         for the CLI interface.
 107
 108     CFG_BRD_LPC1343_802154USBSTICK
 109     ==============================
 110
 111         microBuilder.eu USB stick 802.15.4 868/915MHz RF transceiver
 112
 113     CFG_BRD_LPC1343_OLIMEX_P
 114     ==============================
 115
 116         Simple Olimex LPC1343 breakout board
 117
 118     CFG_BRD_LPC1343_LPCXPRESSO
 119     ==============================
 120
 121         LPC1343 LPCXpresso board
 122
 123     -----------------------------------------------------------------------*/
 124     #define CFG_BRD_LPC1343_REFDESIGN
 125     // #define CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 126     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 127     // #define CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 128     // #define CFG_BRD_LPC1343_802154USBSTICK
 129     // #define CFG_BRD_LPC1343_OLIMEX_P
 130     // #define CFG_BRD_LPC1343_LPCXPRESSO
 131 /*=========================================================================*/
 132
 133
 134 /**************************************************************************
 135     PIN USAGE
 136     -----------------------------------------------------------------------
 137     This table tries to give an indication of which GPIO pins and
 138     peripherals are used by the available drivers and SW examples.  Only
 139     dedicated GPIO pins available on the LPC1343 Reference Board are shown
 140     below.  Any unused peripheral blocks like I2C, SSP, ADC, etc., can
 141     also be used as GPIO if they are available.
 142
 143                 PORT 1        PORT 2                PORT 3
 144                 =========     =================     =======
 145                 8 9 10 11     1 2 3 4 5 6 7 8 9     0 1 2 3
 146
 147     SDCARD      . .  .  .     . . . . . . . . .     X . . .
 148     PWM         . X  .  .     . . . . . . . . .     . . . .
 149     STEPPER     . .  .  .     . . . . . . . . .     X X X X
 150     CHIBI       X X  X  .     . . . . . . . . .     . . . .
 151     ILI9325/8   X X  X  X     X X X X X X X X X     . . . X
 152     ST7565      X X  X  X     X X X X X X X X X     . . . X
 153     ST7735      . .  .  .     X X X X X X . . .     . . . .
 154     SHARPMEM    . .  .  .     X X X X . . . . .     . . . .
 155     SSD1306 SPI . .  .  .     X X X . X X . . .     . . . .
 156     SSD1351     . .  .  .     X X X X X . . . .     . . . .
 157     MCP121      . .  .  .     . . . . . . . . .     . X . .
 158     PN532 [3]   . .  .  .     . . . . . . . . .     . X X .
 159
 160                 TIMERS                    SSP     ADC         UART
 161                 ======================    ===     =======     ====
 162                 16B0  16B1  32B0  32B1    0       0 1 2 3     0
 163
 164     SDCARD      .     .     .     .       X       . . . .     .
 165     PWM         .     X     .     .       .       . . . .     .
 166     PMU [1]     .     .     X     .       .       . . . .     .
 167     USB         .     .     .     X       .       . . . .     .
 168     STEPPER     .     .     X     .       .       . . . .     .
 169     CHIBI       x     .     .     .       X       . . . .     .
 170     ILI9325/8   .     .     .     .       .       X X X X     .
 171     ST7565      .     .     .     .       .       X X X X     .
 172     ST7535      .     .     .     .       .       . . . .     .
 173     SHARPMEM    .     .     .     .       .       . . . .     .
 174     SSD1306 SPI .     .     .     .       .       . . . .     .
 175     INTERFACE   .     .     .     .       .       . . . .     X[2]
 176
 177     [1]  PMU uses 32-bit Timer 0 for SW wakeup from deep-sleep.  This timer
 178          can safely be used by other peripherals, but may need to be
 179          reconfigured when you wakeup from deep-sleep.
 180     [2]  INTERFACE can be configured to use either USBCDC or UART
 181     [3]  P3.2 is only used with the I2C bus (for IRQ)
 182
 183  **************************************************************************/
 184
 185
 186 /**************************************************************************
 187     I2C Addresses
 188     -----------------------------------------------------------------------
 189     The following addresses are used by the different I2C sensors included
 190     in the code base [1]
 191
 192                                 HEX       BINARY
 193                                 ====      ========
 194     ISL12022M (RTC)             0xDE      1101111x
 195     ISL12022M (SRAM)            0xAE      1010111x
 196     LM75B                       0x90      1001000x
 197     MCP24AA                     0xA0      1010000x
 198     MCP4725                     0xC0      1100000x ***
 199     TEA5767                     0xC0      1100000x ***
 200     TSL2561                     0x72      0111001x
 201     TCS3414                     0x72      0111001x
 202     PN532                       0x48      0100100x
 203     SSD1306_I2C                 0x78      0111100x  // Assumes SA0 = GND
 204     INA219                      0xF0      10000000x // Assumes A0+A1 = GND
 205
 206     [1]  Alternative addresses may exists, but the addresses listed in this
 207          table are the values used in the code base
 208
 209  **************************************************************************/
 210
 211
 212 /*=========================================================================
 213     FIRMWARE VERSION SETTINGS
 214     -----------------------------------------------------------------------*/
 215     #define CFG_FIRMWARE_VERSION_MAJOR            (1)
 216     #define CFG_FIRMWARE_VERSION_MINOR            (1)
 217     #define CFG_FIRMWARE_VERSION_REVISION         (0)
 218 /*=========================================================================*/
 219
 220
 221 /*=========================================================================
 222     CORE CPU SETTINGS
 223     -----------------------------------------------------------------------
 224
 225     CFG_CPU_CCLK    Value is for reference only.  'core/cpu/cpu.c' must
 226                     be modified to change the clock speed, but the value
 227                     should be indicated here since CFG_CPU_CCLK is used by
 228                     other peripherals to determine timing.
 229
 230     -----------------------------------------------------------------------*/
 231     #define CFG_CPU_CCLK                (72000000)  // 1 tick = 13.88nS
 232 /*=========================================================================*/
 233
 234
 235 /*=========================================================================
 236     SYSTICK TIMER
 237     -----------------------------------------------------------------------
 238
 239     CFG_SYSTICK_DELAY_IN_MS   The number of milliseconds between each tick
 240                               of the systick timer.
 241
 242     -----------------------------------------------------------------------*/
 243     #define CFG_SYSTICK_DELAY_IN_MS     (1)
 244 /*=========================================================================*/
 245
 246
 247 /*=========================================================================
 248     GPIO INTERRUPTS
 249     -----------------------------------------------------------------------
 250
 251     IF you wish to use the GPIO interrupt handlers elsewhere in your code,
 252     you should probably define a seperate IRQHandler for the appropriate
 253     GPIO bank rather than using the definitions in core/gpio/gpio.c (to
 254     avoid causing problems in other projects, and to make updates easier,
 255     etc.)  To disable the default IRQHandler, simply comment out the
 256     define below for the appropriate GPIO bank and implement the handler
 257     somewhere else.
 258
 259     GPIO_ENABLE_IRQ0    If defined, PIOINT0_IRQHandler will be declared and
 260                         handled in core/gpio/gpio.c
 261     GPIO_ENABLE_IRQ1    If defined, PIOINT1_IRQHandler will be declared and
 262                         handled in core/gpio/gpio.c
 263     GPIO_ENABLE_IRQ2    If defined, PIOINT2_IRQHandler will be declared and
 264                         handled in core/gpio/gpio.c
 265     GPIO_ENABLE_IRQ3    If defined, PIOINT3_IRQHandler will be declared and
 266                         handled in core/gpio/gpio.c
 267
 268     -----------------------------------------------------------------------*/
 269     #ifdef CFG_BRD_LPC1343_REFDESIGN
 270       // #define GPIO_ENABLE_IRQ0
 271       #define GPIO_ENABLE_IRQ1
 272       // #define GPIO_ENABLE_IRQ2
 273       // #define GPIO_ENABLE_IRQ3
 274     #endif
 275
 276     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 277       // #define GPIO_ENABLE_IRQ0
 278       #define GPIO_ENABLE_IRQ1
 279       // #define GPIO_ENABLE_IRQ2
 280       // #define GPIO_ENABLE_IRQ3
 281     #endif
 282
 283     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 284       // #define GPIO_ENABLE_IRQ0
 285       #define GPIO_ENABLE_IRQ1
 286       // #define GPIO_ENABLE_IRQ2
 287       // #define GPIO_ENABLE_IRQ3
 288     #endif
 289
 290     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 291       // #define GPIO_ENABLE_IRQ0
 292       #define GPIO_ENABLE_IRQ1
 293       // #define GPIO_ENABLE_IRQ2
 294       // #define GPIO_ENABLE_IRQ3
 295     #endif
 296
 297     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 298       // #define GPIO_ENABLE_IRQ0
 299       #define GPIO_ENABLE_IRQ1
 300       // #define GPIO_ENABLE_IRQ2
 301       // #define GPIO_ENABLE_IRQ3
 302     #endif
 303
 304     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 305       // #define GPIO_ENABLE_IRQ0
 306       #define GPIO_ENABLE_IRQ1
 307       // #define GPIO_ENABLE_IRQ2
 308       // #define GPIO_ENABLE_IRQ3
 309     #endif
 310
 311     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 312       // #define GPIO_ENABLE_IRQ0
 313       #define GPIO_ENABLE_IRQ1
 314       // #define GPIO_ENABLE_IRQ2
 315       // #define GPIO_ENABLE_IRQ3
 316     #endif
 317 /*=========================================================================*/
 318
 319
 320 /*=========================================================================
 321     ALTERNATE RESET PIN
 322     -----------------------------------------------------------------------
 323
 324     CFG_ALTRESET        If defined, indicates that a GPIO pin should be
 325                         configured as an alternate reset pin in addition
 326                         to the dedicated reset pin.
 327     CFG_ALTRESET_PORT   The GPIO port where the alt reset pin is located
 328     CFG_ALTRESET_PIN    The GPIO pin where the alt reset pin is located
 329
 330     -----------------------------------------------------------------------*/
 331     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 332       #define CFG_ALTRESET
 333       #define CFG_ALTRESET_PORT         (1)
 334       #define CFG_ALTRESET_PIN          (5)   // P1.5 = RTS
 335     #endif
 336 /*=========================================================================*/
 337
 338
 339 /*=========================================================================
 340     UART
 341     -----------------------------------------------------------------------
 342
 343     CFG_UART_BAUDRATE         The default UART speed.  This value is used
 344                               when initialising UART, and should be a
 345                               standard value like 57600, 9600, etc.
 346                               NOTE: This value may be overridden if
 347                               another value is stored in EEPROM!
 348     CFG_UART_BUFSIZE          The length in bytes of the UART RX FIFO. This
 349                               will determine the maximum number of received
 350                               characters to store in memory.
 351
 352     -----------------------------------------------------------------------*/
 353     #ifdef CFG_BRD_LPC1343_REFDESIGN
 354       #define CFG_UART_BAUDRATE           (115200)
 355       #define CFG_UART_BUFSIZE            (512)
 356     #endif
 357
 358     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 359       #define CFG_UART_BAUDRATE           (115200)
 360       #define CFG_UART_BUFSIZE            (512)
 361     #endif
 362
 363     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 364       #define CFG_UART_BAUDRATE           (115200)
 365       #define CFG_UART_BUFSIZE            (512)
 366     #endif
 367
 368     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 369       #define CFG_UART_BAUDRATE           (57600)
 370       #define CFG_UART_BUFSIZE            (512)
 371     #endif
 372
 373     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 374       #define CFG_UART_BAUDRATE           (115200)
 375       #define CFG_UART_BUFSIZE            (512)
 376     #endif
 377
 378     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 379       #define CFG_UART_BAUDRATE           (115200)
 380       #define CFG_UART_BUFSIZE            (512)
 381     #endif
 382
 383     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 384       #define CFG_UART_BAUDRATE           (115200)
 385       #define CFG_UART_BUFSIZE            (512)
 386     #endif
 387 /*=========================================================================*/
 388
 389
 390 /*=========================================================================
 391     SSP
 392     -----------------------------------------------------------------------
 393
 394     CFG_SSP0_SCKPIN_2_11      Indicates which pin should be used for SCK0
 395     CFG_SSP0_SCKPIN_0_6
 396
 397     -----------------------------------------------------------------------*/
 398     #ifdef CFG_BRD_LPC1343_REFDESIGN
 399       #define CFG_SSP0_SCKPIN_2_11
 400       // #define CFG_SSP0_SCKPIN_0_6
 401     #endif
 402
 403     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 404       #define CFG_SSP0_SCKPIN_2_11
 405       // #define CFG_SSP0_SCKPIN_0_6
 406     #endif
 407
 408     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 409       #define CFG_SSP0_SCKPIN_2_11
 410       // #define CFG_SSP0_SCKPIN_0_6
 411     #endif
 412
 413     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 414       // #define CFG_SSP0_SCKPIN_2_11
 415       #define CFG_SSP0_SCKPIN_0_6
 416     #endif
 417
 418     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 419       #define CFG_SSP0_SCKPIN_2_11
 420       // #define CFG_SSP0_SCKPIN_0_6
 421     #endif
 422
 423     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 424       #define CFG_SSP0_SCKPIN_2_11
 425       // #define CFG_SSP0_SCKPIN_0_6
 426     #endif
 427 /*=========================================================================*/
 428
 429
 430 /*=========================================================================
 431     ADC
 432     -----------------------------------------------------------------------
 433
 434     ADC_AVERAGING_ENABLE      To get better results, the ADC code can take
 435                               a number of samples and return the average
 436                               value.  This is slower, but can give more
 437                               accurate results compared to single-reading.
 438
 439                               To enable averaging, set ADC_AVERAGING_ENABLE
 440                               to a non-zero value.
 441     ADC_AVERAGING_SAMPLES     The number of ADC samples to read and
 442                               average if ADC averaging is enabled.
 443
 444     -----------------------------------------------------------------------*/
 445     #ifdef CFG_BRD_LPC1343_REFDESIGN
 446       #define ADC_AVERAGING_ENABLE    (1)
 447       #define ADC_AVERAGING_SAMPLES   (5)
 448     #endif
 449
 450     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 451       #define ADC_AVERAGING_ENABLE    (1)
 452       #define ADC_AVERAGING_SAMPLES   (5)
 453     #endif
 454
 455     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 456       #define ADC_AVERAGING_ENABLE    (0)
 457       #define ADC_AVERAGING_SAMPLES   (5)
 458     #endif
 459
 460     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 461       #define ADC_AVERAGING_ENABLE    (0)
 462       #define ADC_AVERAGING_SAMPLES   (5)
 463     #endif
 464
 465     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 466       #define ADC_AVERAGING_ENABLE    (0)
 467       #define ADC_AVERAGING_SAMPLES   (5)
 468     #endif
 469
 470     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 471       #define ADC_AVERAGING_ENABLE    (0)
 472       #define ADC_AVERAGING_SAMPLES   (5)
 473     #endif
 474 /*=========================================================================*/
 475
 476
 477 /*=========================================================================
 478     ON-BOARD LED
 479     -----------------------------------------------------------------------
 480
 481     CFG_LED_PORT              The port for the on board LED
 482     CFG_LED_PIN               The pin for the on board LED
 483     CFG_LED_ON                The pin state to turn the LED on (0 = low, 1 = high)
 484     CFG_LED_OFF               The pin state to turn the LED off (0 = low, 1 = high)
 485
 486     -----------------------------------------------------------------------*/
 487     #ifdef CFG_BRD_LPC1343_REFDESIGN
 488       #define CFG_LED_PORT                (2)
 489       #define CFG_LED_PIN                 (10)
 490       #define CFG_LED_ON                  (0)
 491       #define CFG_LED_OFF                 (1)
 492     #endif
 493
 494     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 495       #define CFG_LED_PORT                (2)
 496       #define CFG_LED_PIN                 (10)
 497       #define CFG_LED_ON                  (0)
 498       #define CFG_LED_OFF                 (1)
 499     #endif
 500
 501     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 502       #define CFG_LED_PORT                (2)
 503       #define CFG_LED_PIN                 (10)
 504       #define CFG_LED_ON                  (0)
 505       #define CFG_LED_OFF                 (1)
 506     #endif
 507
 508     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 509       #define CFG_LED_PORT                (3)
 510       #define CFG_LED_PIN                 (2)
 511       #define CFG_LED_ON                  (0)
 512       #define CFG_LED_OFF                 (1)
 513     #endif
 514
 515     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 516       #define CFG_LED_PORT                (3)
 517       #define CFG_LED_PIN                 (2)
 518       #define CFG_LED_ON                  (0)
 519       #define CFG_LED_OFF                 (1)
 520     #endif
 521
 522     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 523       #define CFG_LED_PORT                (0)
 524       #define CFG_LED_PIN                 (7)
 525       #define CFG_LED_ON                  (0)
 526       #define CFG_LED_OFF                 (1)
 527     #endif
 528 /*=========================================================================*/
 529
 530
 531 /*=========================================================================
 532     MICRO-SD CARD
 533     -----------------------------------------------------------------------
 534
 535     CFG_SDCARD                If this field is defined SD Card and FAT32
 536                               file system support will be included
 537     CFG_SDCARD_READONLY       If this is set to 1, all commands to
 538                               write to the SD card will be removed
 539                               saving some flash space.
 540     CFG_SDCARD_CDPORT         The card detect port number
 541     CFG_SDCARD_CDPIN          The card detect pin number
 542
 543     NOTE:                     All config settings for FAT32 are defined
 544                               in ffconf.h
 545
 546     BENCHMARK:                With SPI set to 6.0MHz, FATFS can read
 547                               ~300KB/s (w/512 byte read buffer)
 548
 549     PIN LAYOUT:               The pin layout that is used by this driver
 550                               can be seen in the following schematic:
 551                               /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
 552
 553     DEPENDENCIES:             SDCARD requires the use of SSP0.
 554     -----------------------------------------------------------------------*/
 555     #ifdef CFG_BRD_LPC1343_REFDESIGN
 556       // #define CFG_SDCARD
 557       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 558       #define CFG_SDCARD_CDPORT           (3)
 559       #define CFG_SDCARD_CDPIN            (0)
 560     #endif
 561
 562     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 563       // #define CFG_SDCARD
 564       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 565       #define CFG_SDCARD_CDPORT           (3)
 566       #define CFG_SDCARD_CDPIN            (0)
 567     #endif
 568
 569     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 570       #define CFG_SDCARD
 571       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 572       #define CFG_SDCARD_CDPORT           (3)
 573       #define CFG_SDCARD_CDPIN            (0)
 574     #endif
 575
 576     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 577       // #define CFG_SDCARD
 578       #define CFG_SDCARD_READONLY         (1)   // Must be 0 or 1
 579       #define CFG_SDCARD_CDPORT           (3)
 580       #define CFG_SDCARD_CDPIN            (0)
 581     #endif
 582
 583     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 584       // #define CFG_SDCARD
 585       #define CFG_SDCARD_READONLY         (1) // Must be 0 or 1
 586       #define CFG_SDCARD_CDPORT           (3)
 587       #define CFG_SDCARD_CDPIN            (0)
 588     #endif
 589
 590     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 591       // #define CFG_SDCARD
 592       #define CFG_SDCARD_READONLY         (1) // Must be 0 or 1
 593       #define CFG_SDCARD_CDPORT           (3)
 594       #define CFG_SDCARD_CDPIN            (0)
 595     #endif
 596 /*=========================================================================*/
 597
 598
 599 /*=========================================================================
 600     USB
 601     -----------------------------------------------------------------------
 602
 603     CFG_USBHID                If this field is defined USB HID support will
 604                               be included.  Currently uses ROM-based USB HID
 605     CFG_USBCDC                If this field is defined USB CDC support will
 606                               be included, with the USB Serial Port speed
 607                               set to 115200 BPS by default
 608     CFG_USBCDC_BAUDRATE       The default TX/RX speed.  This value is used
 609                               when initialising USBCDC, and should be a
 610                               standard value like 57600, 9600, etc.
 611     CFG_USBCDC_INITTIMEOUT    The maximum delay in milliseconds to wait for
 612                               USB to connect.  Must be a multiple of 10!
 613     CFG_USBCDC_BUFFERSIZE     Size of the buffer (in bytes) that stores
 614                               printf data until it can be sent out in
 615                               64 byte frames.  The buffer is required since
 616                               only one frame per ms can be sent using USB
 617                               CDC (see 'puts' in systeminit.c).
 618
 619     -----------------------------------------------------------------------*/
 620     #define CFG_USB_VID                   (0x239A)
 621     #define CFG_USB_PID                   (0x1002)
 622
 623     #ifdef CFG_BRD_LPC1343_REFDESIGN
 624       // #define CFG_USBHID
 625       #define CFG_USBCDC
 626       #define CFG_USBCDC_BAUDRATE         (115200)
 627       #define CFG_USBCDC_INITTIMEOUT      (5000)
 628       #define CFG_USBCDC_BUFFERSIZE       (256)
 629     #endif
 630
 631     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 632       // #define CFG_USBHID
 633       // #define CFG_USBCDC
 634       #define CFG_USBCDC_BAUDRATE         (115200)
 635       #define CFG_USBCDC_INITTIMEOUT      (5000)
 636       #define CFG_USBCDC_BUFFERSIZE       (256)
 637     #endif
 638
 639     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 640       // #define CFG_USBHID
 641       #define CFG_USBCDC
 642       #define CFG_USBCDC_BAUDRATE         (115200)
 643       #define CFG_USBCDC_INITTIMEOUT      (5000)
 644       #define CFG_USBCDC_BUFFERSIZE       (256)
 645     #endif
 646
 647     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 648       // #define CFG_USBHID
 649       // #define CFG_USBCDC
 650       #define CFG_USBCDC_BAUDRATE         (57600)
 651       #define CFG_USBCDC_INITTIMEOUT      (5000)
 652       #define CFG_USBCDC_BUFFERSIZE       (256)
 653     #endif
 654
 655     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 656       // #define CFG_USBHID
 657       #define CFG_USBCDC
 658       #define CFG_USBCDC_BAUDRATE         (115200)
 659       #define CFG_USBCDC_INITTIMEOUT      (5000)
 660       #define CFG_USBCDC_BUFFERSIZE       (256)
 661     #endif
 662
 663     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 664       // #define CFG_USBHID
 665       #define CFG_USBCDC
 666       #define CFG_USBCDC_BAUDRATE         (115200)
 667       #define CFG_USBCDC_INITTIMEOUT      (5000)
 668       #define CFG_USBCDC_BUFFERSIZE       (256)
 669     #endif
 670
 671     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 672       // #define CFG_USBHID
 673       #define CFG_USBCDC
 674       #define CFG_USBCDC_BAUDRATE         (115200)
 675       #define CFG_USBCDC_INITTIMEOUT      (5000)
 676       #define CFG_USBCDC_BUFFERSIZE       (256)
 677     #endif
 678 /*=========================================================================*/
 679
 680
 681 /*=========================================================================
 682     PRINTF REDIRECTION
 683     -----------------------------------------------------------------------
 684
 685     CFG_PRINTF_MAXSTRINGSIZE  Maximum size of string buffer for printf
 686     CFG_PRINTF_UART           Will cause all printf statements to be
 687                               redirected to UART
 688     CFG_PRINTF_USBCDC         Will cause all printf statements to be
 689                               redirect to USB Serial
 690     CFG_PRINTF_NEWLINE        This is typically "\r\n" for Windows or
 691                               "\n" for *nix
 692
 693     Note: If no printf redirection definitions are present, all printf
 694     output will be ignored.
 695     -----------------------------------------------------------------------*/
 696     #ifdef CFG_BRD_LPC1343_REFDESIGN
 697       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 698       // #define CFG_PRINTF_UART
 699       #define CFG_PRINTF_USBCDC
 700       #define CFG_PRINTF_NEWLINE          "\r\n"
 701     #endif
 702
 703     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 704       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 705       #define CFG_PRINTF_UART
 706       // #define CFG_PRINTF_USBCDC
 707       #define CFG_PRINTF_NEWLINE          "\r\n"
 708     #endif
 709
 710     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 711       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 712       // #define CFG_PRINTF_UART
 713       #define CFG_PRINTF_USBCDC
 714       #define CFG_PRINTF_NEWLINE          "\r\n"
 715     #endif
 716
 717     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 718       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 719       #define CFG_PRINTF_UART
 720       // #define CFG_PRINTF_USBCDC
 721       #define CFG_PRINTF_NEWLINE          "\n"
 722     #endif
 723
 724     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 725       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 726       // #define CFG_PRINTF_UART
 727       #define CFG_PRINTF_USBCDC
 728       #define CFG_PRINTF_NEWLINE          "\r\n"
 729     #endif
 730
 731     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 732       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 733       // #define CFG_PRINTF_UART
 734       #define CFG_PRINTF_USBCDC
 735       #define CFG_PRINTF_NEWLINE          "\r\n"
 736     #endif
 737
 738     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 739       #define CFG_PRINTF_MAXSTRINGSIZE    (255)
 740       // #define CFG_PRINTF_UART
 741       #define CFG_PRINTF_USBCDC
 742       #define CFG_PRINTF_NEWLINE          "\r\n"
 743     #endif
 744 /*=========================================================================*/
 745
 746
 747 /*=========================================================================
 748     COMMAND LINE INTERFACE
 749     -----------------------------------------------------------------------
 750
 751     CFG_INTERFACE             If this field is defined the UART or USBCDC
 752                               based command-line interface will be included
 753     CFG_INTERFACE_MAXMSGSIZE  The maximum number of bytes to accept for an
 754                               incoming command
 755     CFG_INTERFACE_PROMPT      The command prompt to display at the start
 756                               of every new data entry line
 757     CFG_INTERFACE_SILENTMODE  If this is set to 1 only text generated in
 758                               response to commands will be send to the
 759                               output buffer.  The command prompt will not
 760                               be displayed and incoming text will not be
 761                               echoed back to the output buffer (allowing
 762                               you to see the text you have input).  This
 763                               is normally only desirable in a situation
 764                               where another MCU is communicating with
 765                               the LPC1343.
 766     CFG_INTERFACE_DROPCR      If this is set to 1 all incoming \r
 767                               characters will be dropped
 768     CFG_INTERFACE_ENABLEIRQ   If this is set to 1 the IRQ pin will be
 769                               set high when a command starts executing
 770                               and will go low when the command has
 771                               finished executing or the LCD is not busy.
 772                               This allows another device to know when a
 773                               new command can safely be sent.
 774     CFG_INTERFACE_IRQPORT     The gpio port for the IRQ/busy pin
 775     CFG_INTERFACE_IRQPIN      The gpio pin number for the IRQ/busy pin
 776     CFG_INTERFACE_SHORTERRORS If this is enabled only short 1 character
 777                               error messages will be returned (followed
 778                               by CFG_PRINTF_NEWLINE), rather than more
 779                               verbose error messages.  The specific
 780                               characters used are defined below.
 781     CFG_INTERFACE_CONFIRMREADY  If this is set to 1 a text confirmation
 782                               will be sent when the command prompt is
 783                               ready for a new command.  This is in
 784                               addition to CFG_INTERFACE_ENABLEIRQ if
 785                               this is also enabled.  The character used
 786                               is defined below.
 787     CFG_INTERFACE_LONGSYSINFO If this is set to 1 extra information will
 788                               be included in the Sys Info ('V') command
 789                               on the CLI. This can be useful when trying
 790                               to debug problems on remote HW, or with
 791                               unknown firmware.  It will also use about
 792                               0.5KB flash, though, so only enable it is
 793                               necessary.
 794
 795     NOTE:                     The command-line interface will use either
 796                               USB-CDC or UART depending on whether
 797                               CFG_PRINTF_UART or CFG_PRINTF_USBCDC are
 798                               selected.
 799     -----------------------------------------------------------------------*/
 800     #ifdef CFG_BRD_LPC1343_REFDESIGN
 801       #define CFG_INTERFACE
 802       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 803       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 804       #define CFG_INTERFACE_SILENTMODE    (0)
 805       #define CFG_INTERFACE_DROPCR        (0)
 806       #define CFG_INTERFACE_ENABLEIRQ     (0)
 807       #define CFG_INTERFACE_IRQPORT       (0)
 808       #define CFG_INTERFACE_IRQPIN        (7)
 809       #define CFG_INTERFACE_SHORTERRORS   (0)
 810       #define CFG_INTERFACE_CONFIRMREADY  (0)
 811       #define CFG_INTERFACE_LONGSYSINFO   (0)
 812     #endif
 813
 814     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 815       // #define CFG_INTERFACE
 816       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 817       #define CFG_INTERFACE_PROMPT        "LPC1343 >> "
 818       #define CFG_INTERFACE_SILENTMODE    (0)
 819       #define CFG_INTERFACE_DROPCR        (0)
 820       #define CFG_INTERFACE_ENABLEIRQ     (0)
 821       #define CFG_INTERFACE_IRQPORT       (0)
 822       #define CFG_INTERFACE_IRQPIN        (7)
 823       #define CFG_INTERFACE_SHORTERRORS   (0)
 824       #define CFG_INTERFACE_CONFIRMREADY  (0)
 825       #define CFG_INTERFACE_LONGSYSINFO   (0)
 826     #endif
 827
 828     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB
 829       #define CFG_INTERFACE
 830       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 831       #define CFG_INTERFACE_PROMPT        "CMD >> "
 832       #define CFG_INTERFACE_SILENTMODE    (0)
 833       #define CFG_INTERFACE_DROPCR        (0)
 834       #define CFG_INTERFACE_ENABLEIRQ     (0)
 835       #define CFG_INTERFACE_IRQPORT       (0)
 836       #define CFG_INTERFACE_IRQPIN        (7)
 837       #define CFG_INTERFACE_SHORTERRORS   (0)
 838       #define CFG_INTERFACE_CONFIRMREADY  (0)
 839       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 840       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 841       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 842       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 843       #define CFG_INTERFACE_LONGSYSINFO   (0)
 844     #endif
 845
 846     #ifdef CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 847       #define CFG_INTERFACE
 848       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 849       #define CFG_INTERFACE_PROMPT        ">>"
 850       #define CFG_INTERFACE_SILENTMODE    (1)
 851       #define CFG_INTERFACE_DROPCR        (1)
 852       #define CFG_INTERFACE_ENABLEIRQ     (1)
 853       #define CFG_INTERFACE_IRQPORT       (0)
 854       #define CFG_INTERFACE_IRQPIN        (7)
 855       #define CFG_INTERFACE_SHORTERRORS   (1)
 856       #define CFG_INTERFACE_CONFIRMREADY  (0)
 857       #define CFG_INTERFACE_SHORTERRORS_UNKNOWNCOMMAND    "?"
 858       #define CFG_INTERFACE_SHORTERRORS_TOOMANYARGS       ">"
 859       #define CFG_INTERFACE_SHORTERRORS_TOOFEWARGS        "<"
 860       #define CFG_INTERFACE_CONFIRMREADY_TEXT             "."
 861       #define CFG_INTERFACE_LONGSYSINFO   (0)
 862     #endif
 863
 864     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 865       // #define CFG_INTERFACE
 866       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 867       #define CFG_INTERFACE_PROMPT        "CMD >> "
 868       #define CFG_INTERFACE_SILENTMODE    (0)
 869       #define CFG_INTERFACE_DROPCR        (0)
 870       #define CFG_INTERFACE_ENABLEIRQ     (0)
 871       #define CFG_INTERFACE_IRQPORT       (0)
 872       #define CFG_INTERFACE_IRQPIN        (7)
 873       #define CFG_INTERFACE_SHORTERRORS   (0)
 874       #define CFG_INTERFACE_CONFIRMREADY  (0)
 875       #define CFG_INTERFACE_LONGSYSINFO   (0)
 876     #endif
 877
 878     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 879       #define CFG_INTERFACE
 880       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 881       #define CFG_INTERFACE_PROMPT        "LPC-P1343 >> "
 882       #define CFG_INTERFACE_SILENTMODE    (0)
 883       #define CFG_INTERFACE_DROPCR        (0)
 884       #define CFG_INTERFACE_ENABLEIRQ     (0)
 885       #define CFG_INTERFACE_IRQPORT       (0)
 886       #define CFG_INTERFACE_IRQPIN        (7)
 887       #define CFG_INTERFACE_SHORTERRORS   (0)
 888       #define CFG_INTERFACE_CONFIRMREADY  (0)
 889       #define CFG_INTERFACE_LONGSYSINFO   (0)
 890     #endif
 891
 892     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 893       #define CFG_INTERFACE
 894       #define CFG_INTERFACE_MAXMSGSIZE    (256)
 895       #define CFG_INTERFACE_PROMPT        "LPC-P1343 >> "
 896       #define CFG_INTERFACE_SILENTMODE    (0)
 897       #define CFG_INTERFACE_DROPCR        (0)
 898       #define CFG_INTERFACE_ENABLEIRQ     (0)
 899       #define CFG_INTERFACE_IRQPORT       (0)
 900       #define CFG_INTERFACE_IRQPIN        (7)
 901       #define CFG_INTERFACE_SHORTERRORS   (0)
 902       #define CFG_INTERFACE_CONFIRMREADY  (0)
 903       #define CFG_INTERFACE_LONGSYSINFO   (0)
 904     #endif
 905 /*=========================================================================*/
 906
 907
 908 /*=========================================================================
 909     PWM SETTINGS
 910     -----------------------------------------------------------------------
 911
 912     CFG_PWM                     If this is defined, a basic PWM driver
 913                                 will be included using 16-bit Timer 1 and
 914                                 Pin 1.9 (MAT0) for the PWM output.  In
 915                                 order to allow for a fixed number of
 916                                 pulses to be generated, some PWM-specific
 917                                 code is required in the 16-Bit Timer 1
 918                                 ISR.  See "core/timer16/timer16.c" for
 919                                 more information.
 920     CFG_PWM_DEFAULT_PULSEWIDTH  The default pulse width in ticks
 921     CFG_PWM_DEFAULT_DUTYCYCLE   The default duty cycle in percent
 922
 923     DEPENDENCIES:               PWM output requires the use of 16-bit
 924                                 timer 1 and pin 1.9 (CT16B1_MAT0).
 925     -----------------------------------------------------------------------*/
 926     // #define CFG_PWM
 927     #define CFG_PWM_DEFAULT_PULSEWIDTH  (CFG_CPU_CCLK / 1000)
 928     #define CFG_PWM_DEFAULT_DUTYCYCLE   (50)
 929 /*=========================================================================*/
 930
 931
 932 /*=========================================================================
 933     STEPPER MOTOR SETTINGS
 934     -----------------------------------------------------------------------
 935
 936     CFG_STEPPER                 If this is defined, a simple bi-polar
 937                                 stepper motor will be included for common
 938                                 H-bridge chips like the L293D or SN754410N
 939
 940     DEPENDENCIES:               STEPPER requires the use of pins 3.0-3 and
 941                                 32-bit Timer 0.
 942     -----------------------------------------------------------------------*/
 943     // #define CFG_STEPPER
 944 /*=========================================================================*/
 945
 946
 947 /*=========================================================================
 948     EEPROM
 949     -----------------------------------------------------------------------
 950
 951     CFG_I2CEEPROM             If defined, drivers for the onboard EEPROM
 952                               will be included during build
 953     CFG_I2CEEPROM_SIZE        The number of bytes available on the EEPROM
 954
 955     -----------------------------------------------------------------------*/
 956     #ifdef CFG_BRD_LPC1343_REFDESIGN
 957       #define CFG_I2CEEPROM
 958       #define CFG_I2CEEPROM_SIZE          (3072)
 959     #endif
 960
 961     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
 962       // #define CFG_I2CEEPROM
 963       #define CFG_I2CEEPROM_SIZE          (3072)
 964     #endif
 965
 966     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
 967       #define CFG_I2CEEPROM
 968       #define CFG_I2CEEPROM_SIZE          (3072)
 969     #endif
 970
 971     #ifdef CFG_BRD_LPC1343_802154USBSTICK
 972       #define CFG_I2CEEPROM
 973       #define CFG_I2CEEPROM_SIZE          (3072)
 974     #endif
 975
 976     #ifdef CFG_BRD_LPC1343_OLIMEX_P
 977       // #define CFG_I2CEEPROM
 978       #define CFG_I2CEEPROM_SIZE          (3072)
 979     #endif
 980
 981     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
 982       // #define CFG_I2CEEPROM
 983       #define CFG_I2CEEPROM_SIZE          (3072)
 984     #endif
 985 /*=========================================================================*/
 986
 987
 988 /*=========================================================================
 989     EEPROM MEMORY MAP
 990     -----------------------------------------------------------------------
 991     EEPROM is used to persist certain user modifiable values to make
 992     sure that these changes remain in effect after a reset or hard
 993     power-down.  The addresses in EEPROM for these various system
 994     settings/values are defined below.  The first 256 bytes of EEPROM
 995     are reserved for this (0x0000..0x00FF).
 996
 997     CFG_EEPROM_RESERVED       The last byte of reserved EEPROM memory
 998
 999           EEPROM Address (0x0000..0x00FF)
1000           ===============================
1001           0 1 2 3 4 5 6 7 8 9 A B C D E F
1002     000x  x x x x x x x x . x x . . . . .   Chibi
1003     001x  . . . . . . . . . . . . . . . .
1004     002x  x x x x . . . . . . . . . . . .   UART
1005     003x  x x x x x x x x x x x x x x x x   Touch Screen Calibration
1006     004x  x x x x x x x x x x x x x x . .   Touch Screen Calibration
1007     005x  . . . . . . . . . . . . . . . .
1008     006x  . . . . . . . . . . . . . . . .
1009     007x  . . . . . . . . . . . . . . . .
1010     008x  . . . . . . . . . . . . . . . .
1011     009x  . . . . . . . . . . . . . . . .
1012     00Ax  . . . . . . . . . . . . . . . .
1013     00Bx  . . . . . . . . . . . . . . . .
1014     00Cx  . . . . . . . . . . . . . . . .
1015     00Dx  . . . . . . . . . . . . . . . .
1016     00Ex  . . . . . . . . . . . . . . . .
1017     00Fx  . . . . . . . . . . . . . . . .
1018
1019     -----------------------------------------------------------------------*/
1020     #define CFG_EEPROM_RESERVED                 (0x00FF)              // Protect first 256 bytes of memory
1021     #define CFG_EEPROM_CHIBI_IEEEADDR           (uint16_t)(0x0000)    // 8
1022     #define CFG_EEPROM_CHIBI_SHORTADDR          (uint16_t)(0x0009)    // 2
1023     #define CFG_EEPROM_UART_SPEED               (uint16_t)(0x0020)    // 4
1024     #define CFG_EEPROM_TOUCHSCREEN_CALIBRATED   (uint16_t)(0x0030)    // 1
1025     #define CFG_EEPROM_TOUCHSCREEN_CAL_AN       (uint16_t)(0x0031)    // 4
1026     #define CFG_EEPROM_TOUCHSCREEN_CAL_BN       (uint16_t)(0x0035)    // 4
1027     #define CFG_EEPROM_TOUCHSCREEN_CAL_CN       (uint16_t)(0x0039)    // 4
1028     #define CFG_EEPROM_TOUCHSCREEN_CAL_DN       (uint16_t)(0x003D)    // 4
1029     #define CFG_EEPROM_TOUCHSCREEN_CAL_EN       (uint16_t)(0x0041)    // 4
1030     #define CFG_EEPROM_TOUCHSCREEN_CAL_FN       (uint16_t)(0x0045)    // 4
1031     #define CFG_EEPROM_TOUCHSCREEN_CAL_DIVIDER  (uint16_t)(0x0049)    // 4
1032     #define CFG_EEPROM_TOUCHSCREEN_THRESHHOLD   (uint16_t)(0x004D)    // 1
1033 /*=========================================================================*/
1034
1035
1036 /*=========================================================================
1037     LM75B TEMPERATURE SENSOR
1038     -----------------------------------------------------------------------
1039
1040     CFG_LM75B                 If defined, drivers for an optional LM75B
1041                               temperature sensor will be included during
1042                               build (requires external HW)
1043
1044     -----------------------------------------------------------------------*/
1045     // #define CFG_LM75B
1046 /*=========================================================================*/
1047
1048
1049 /*=========================================================================
1050     CHIBI WIRELESS STACK
1051     -----------------------------------------------------------------------
1052
1053     CFG_CHIBI                   If defined, the CHIBI wireless stack will be
1054                                 included during build.  Requires external HW.
1055     CFG_CHIBI_MODE              The mode to use when receiving and transmitting
1056                                 wireless data.  See chb_drvr.h for possible values
1057     CFG_CHIBI_POWER             The power level to use when transmitting.  See
1058                                 chb_drvr.h for possible values
1059     CFG_CHIBI_CHANNEL           802.15.4 Channel (0 = 868MHz, 1-10 = 915MHz)
1060     CFG_CHIBI_PANID             16-bit PAN Identifier (ex.0x1234)
1061     CFG_CHIBI_PROMISCUOUS       Set to 1 to enabled promiscuous mode or
1062                                 0 to disable it.  If promiscuous mode is
1063                                 enabled be sure to set CFG_CHIBI_BUFFERSIZE
1064                                 to an appropriately large value (ex. 1024)
1065     CFG_CHIBI_BUFFERSIZE        The size of the message buffer in bytes
1066
1067     DEPENDENCIES:               Chibi requires the use of SSP0, 16-bit timer
1068                                 0 and pins 3.1, 3.2, 3.3.  It also requires
1069                                 the presence of CFG_I2CEEPROM.
1070
1071     NOTE:                       These settings are not relevant to all boards!
1072                                 'tools/schematics/AT86RF212LPC1114_v1.6.pdf'
1073                                 show how 'CHIBI' is meant to be connected
1074     -----------------------------------------------------------------------*/
1075     #ifdef CFG_BRD_LPC1343_REFDESIGN
1076       // #define CFG_CHIBI
1077       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1078       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1079       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1080       #define CFG_CHIBI_PANID             (0x1234)
1081       #define CFG_CHIBI_PROMISCUOUS       (0)
1082       #define CFG_CHIBI_BUFFERSIZE        (128)
1083     #endif
1084
1085     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
1086       // #define CFG_CHIBI
1087       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1088       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1089       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1090       #define CFG_CHIBI_PANID             (0x1234)
1091       #define CFG_CHIBI_PROMISCUOUS       (0)
1092       #define CFG_CHIBI_BUFFERSIZE        (128)
1093     #endif
1094
1095     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
1096       // #define CFG_CHIBI
1097       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1098       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1099       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1100       #define CFG_CHIBI_PANID             (0x1234)
1101       #define CFG_CHIBI_PROMISCUOUS       (0)
1102       #define CFG_CHIBI_BUFFERSIZE        (128)
1103     #endif
1104
1105     #ifdef CFG_BRD_LPC1343_802154USBSTICK
1106       #define CFG_CHIBI
1107       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1108       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1109       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1110       #define CFG_CHIBI_PANID             (0x1234)
1111       #define CFG_CHIBI_PROMISCUOUS       (0)
1112       #define CFG_CHIBI_BUFFERSIZE        (1024)
1113     #endif
1114
1115     #ifdef CFG_BRD_LPC1343_OLIMEX_P
1116       // #define CFG_CHIBI
1117       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1118       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1119       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1120       #define CFG_CHIBI_PANID             (0x1234)
1121       #define CFG_CHIBI_PROMISCUOUS       (0)
1122       #define CFG_CHIBI_BUFFERSIZE        (128)
1123     #endif
1124
1125     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
1126       // #define CFG_CHIBI
1127       #define CFG_CHIBI_MODE              (0)                 // OQPSK_868MHZ
1128       #define CFG_CHIBI_POWER             (0xE9)              // CHB_PWR_EU2_3DBM
1129       #define CFG_CHIBI_CHANNEL           (0)                 // 868-868.6 MHz
1130       #define CFG_CHIBI_PANID             (0x1234)
1131       #define CFG_CHIBI_PROMISCUOUS       (0)
1132       #define CFG_CHIBI_BUFFERSIZE        (128)
1133     #endif
1134 /*=========================================================================*/
1135
1136
1137 /*=========================================================================
1138     TFT LCD
1139     -----------------------------------------------------------------------
1140
1141     CFG_TFTLCD                  If defined, this will cause drivers for
1142                                 a pre-determined LCD screen to be included
1143                                 during build.  Only one LCD driver can be
1144                                 included during the build process (for ex.
1145                                 'drivers/displays/hw/ILI9325.c')
1146     CFG_TFTLCD_INCLUDESMALLFONTS If set to 1, smallfont support will be
1147                                 included for 3x6, 5x8, 7x8 and 8x8 fonts.
1148                                 This should only be enabled if these small
1149                                 fonts are required since there is already
1150                                 support for larger fonts generated with
1151                                 Dot Factory
1152                                 http://www.pavius.net/downloads/tools/53-the-dot-factory
1153     CFG_TFTLCD_USEAAFONTS       If set to a non-zero value, anti-aliased
1154                                 fonts will be used instead of regular 1-bit
1155                                 font.  These result in much higher-
1156                                 quality text, but the fonts are 2 or 4
1157                                 times larger than plain bitmap fonts and
1158                                 take a bit more rendering time to display.
1159     CFG_TFTLCD_TS_DEFAULTTHRESHOLD  Default minimum threshold to trigger a
1160                                 touch event with the touch screen (and exit
1161                                 from 'tsWaitForEvent' in touchscreen.c).
1162                                 Should be an 8-bit value somewhere between
1163                                 8 and 75 in normal circumstances.  This is
1164                                 the default value and may be overriden by
1165                                 a value stored in EEPROM.
1166     CFG_TFTLCD_TS_KEYPADDELAY   The delay in milliseconds between key
1167                                 presses in dialogue boxes
1168
1169     PIN LAYOUT:                 The pin layout that is used by this driver
1170                                 can be seen in the following schematic:
1171                                 /tools/schematics/Breakout_TFTLCD_ILI9325_v1.3
1172
1173     DEPENDENCIES:               TFTLCD requires the use of pins 1.8, 1.9,
1174                                 1.10, 1.11, 3.3 and 2.1-9.
1175     -----------------------------------------------------------------------*/
1176     #ifdef CFG_BRD_LPC1343_REFDESIGN
1177       // #define CFG_TFTLCD
1178       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1179       #define CFG_TFTLCD_USEAAFONTS          (0)
1180       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1181       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1182     #endif
1183
1184     #ifdef CFG_BRD_LPC1343_REFDESIGN_MINIMAL
1185       // #define CFG_TFTLCD
1186       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1187       #define CFG_TFTLCD_USEAAFONTS          (0)
1188       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1189       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1190     #endif
1191
1192     #if defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB || defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART
1193       #define CFG_TFTLCD
1194       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1195       #define CFG_TFTLCD_USEAAFONTS          (0)
1196       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1197       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1198     #endif
1199
1200     #ifdef CFG_BRD_LPC1343_802154USBSTICK
1201       // #define CFG_TFTLCD
1202       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1203       #define CFG_TFTLCD_USEAAFONTS          (0)
1204       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1205       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1206     #endif
1207
1208     #ifdef CFG_BRD_LPC1343_OLIMEX_P
1209       // #define CFG_TFTLCD
1210       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1211       #define CFG_TFTLCD_USEAAFONTS          (0)
1212       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1213       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1214     #endif
1215
1216     #ifdef CFG_BRD_LPC1343_LPCXPRESSO
1217       // #define CFG_TFTLCD
1218       #define CFG_TFTLCD_INCLUDESMALLFONTS   (0)
1219       #define CFG_TFTLCD_USEAAFONTS          (0)
1220       #define CFG_TFTLCD_TS_DEFAULTTHRESHOLD (50)
1221       #define CFG_TFTLCD_TS_KEYPADDELAY      (100)
1222     #endif
1223 /*=========================================================================*/
1224
1225
1226 /*=========================================================================
1227     Monochrome/Bitmap Graphic LCDs
1228     -----------------------------------------------------------------------
1229
1230     CFG_ST7565                If defined, this will cause drivers for
1231                               the 128x64 pixel ST7565 LCD to be included
1232     CFG_SSD1306               If defined, this will cause drivers for
1233                               the 128x64 pixel SSD1306 OLED display to be
1234                               included (using bit-banged SPI)
1235     CFG_SHARPMEM              If defined, this will cause drivers for
1236                               Sharp Memory Displays to be included
1237
1238     DEPENDENCIES:             ST7565 requires the use of pins 2.1-6.
1239     DEPENDENCIES:             SSD1306 requires the use of pins 2.1-6.
1240     DEPENDENCIES:             SSD1306_I2C requires the use of pins 2.2.
1241     DEPENDENCIES:             SHARPMEM requires the use of pins 2.1-4.
1242     -----------------------------------------------------------------------*/
1243     // #define CFG_ST7565
1244     // #define CFG_SSD1306
1245     // #define CFG_SHARPMEM
1246 /*=========================================================================*/
1247
1248
1249 /*=========================================================================
1250     RSA Encryption
1251     -----------------------------------------------------------------------
1252
1253     CFG_RSA                     If defined, support for basic RSA
1254                                 encryption will be included.
1255     CFG_RSA_BITS                Indicates the number of bits used for
1256                                 RSA encryption keys.  To keep code size
1257                                 reasonable, RSA encryption is currently
1258                                 limited to using 64-bit or 32-bit numbers,
1259                                 with 64-bit providing higher security, and
1260                                 32-bit providing smaller encrypted text
1261                                 size.
1262
1263     NOTE:                       Please note that Printf can not be
1264                                 used to display 64-bit values (%lld)!
1265     -----------------------------------------------------------------------*/
1266     // #define CFG_RSA
1267     #define CFG_RSA_BITS                  (32)
1268 /*=========================================================================*/
1269
1270
1271
1272
1273 /*=========================================================================
1274   CONFIG FILE VALIDATION
1275   -------------------------------------------------------------------------
1276   Basic error checking to make sure that incompatible defines are not
1277   enabled at the same time, etc.
1278
1279   =========================================================================*/
1280
1281 #if !defined CFG_BRD_LPC1343_REFDESIGN && \
1282   !defined CFG_BRD_LPC1343_REFDESIGN_MINIMAL && \
1283   !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_USB && \
1284   !defined CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART && \
1285   !defined CFG_BRD_LPC1343_802154USBSTICK && \
1286   !defined CFG_BRD_LPC1343_OLIMEX_P && \
1287   !defined CFG_BRD_LPC1343_LPCXPRESSO
1288   #error "You must defined a target board (CFG_BRD_LPC1343_REFDESIGN or CFG_BRD_LPC1343_REFDESIGN_MINIMAL or CFG_BRD_LPC1343_TFTLCDSTANDALONE or CFG_BRD_LPC1343_TFTLCDSTANDALONE_UART or CFG_BRD_LPC1343_802154USBSTICK or CFG_BRD_LPC1343_LPCXPRESSO)"
1289 #endif
1290
1291 #if defined CFG_PRINTF_USBCDC && defined CFG_PRINTF_UART
1292   #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC cannot both be defined at once"
1293 #endif
1294
1295 #if defined CFG_PRINTF_USBCDC && !defined CFG_USBCDC
1296   #error "CFG_PRINTF_CDC requires CFG_USBCDC to be defined as well"
1297 #endif
1298
1299 #if defined CFG_USBCDC && defined CFG_USBHID
1300   #error "Only one USB class can be defined at a time (CFG_USBCDC or CFG_USBHID)"
1301 #endif
1302
1303 #if defined CFG_SSP0_SCKPIN_2_11 && defined CFG_SSP0_SCKPIN_0_6
1304   #error "Only one SCK pin can be defined at a time for SSP0"
1305 #endif
1306
1307 #if !defined CFG_SSP0_SCKPIN_2_11 && !defined CFG_SSP0_SCKPIN_0_6
1308   #error "An SCK pin must be selected for SSP0 (CFG_SSP0_SCKPIN_2_11 or CFG_SSP0_SCKPIN_0_6)"
1309 #endif
1310
1311 #ifdef CFG_INTERFACE
1312   #if !defined CFG_PRINTF_UART && !defined CFG_PRINTF_USBCDC
1313     #error "CFG_PRINTF_UART or CFG_PRINTF_USBCDC must be defined for for CFG_INTERFACE Input/Output"
1314   #endif
1315   #if defined CFG_PRINTF_USBCDC && CFG_INTERFACE_SILENTMODE == 1
1316     #error "CFG_INTERFACE_SILENTMODE typically isn't enabled with CFG_PRINTF_USBCDC"
1317   #endif
1318 #endif
1319
1320 #ifdef CFG_CHIBI
1321   #if !defined CFG_I2CEEPROM
1322     #error "CFG_CHIBI requires CFG_I2CEEPROM to store and retrieve addresses"
1323   #endif
1324   #ifdef CFG_SDCARD
1325     #error "CFG_CHIBI and CFG_SDCARD can not be defined at the same time. Only one SPI block is available on the LPC1343."
1326   #endif
1327   #ifdef CFG_TFTLCD
1328     #error "CFG_CHIBI and CFG_TFTLCD can not be defined at the same time since they both use pins 1.8, 1.9 and 1.10."
1329   #endif
1330   #ifdef CFG_PWM
1331     #error "CFG_CHIBI and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1332   #endif
1333   #if CFG_CHIBI_PROMISCUOUS != 0 && CFG_CHIBI_PROMISCUOUS != 1
1334     #error "CFG_CHIBI_PROMISCUOUS must be equal to either 1 or 0"
1335   #endif
1336   #if !defined GPIO_ENABLE_IRQ1
1337     #error "GPIO_ENABLE_IRQ1 must be enabled when using Chibi (Chibi IRQ is on GPIO1.8)"
1338   #endif
1339 #endif
1340
1341 #ifdef CFG_TFTLCD
1342   #ifdef CFG_ST7565
1343     #error "CFG_TFTLCD and CFG_ST7565 can not be defined at the same time."
1344   #endif
1345   #ifdef CFG_SSD1306
1346     #error "CFG_TFTLCD and CFG_SSD1306 can not be defined at the same time."
1347   #endif
1348   #ifdef CFG_SHARPMEM
1349     #error "CFG_TFTLCD and CFG_SHARPMEM can not be defined at the same time."
1350   #endif
1351   #ifdef CFG_PWM
1352     #error "CFG_TFTLCD and CFG_PWM can not be defined at the same time since they both use pin 1.9."
1353   #endif
1354   #if !defined CFG_I2CEEPROM
1355     #error "CFG_TFTLCD requires CFG_I2CEEPROM to store and retrieve configuration settings"
1356   #endif
1357 #endif
1358
1359 #ifdef CFG_SDCARD
1360   #ifdef CFG_STEPPER
1361     #error  "CFG_SDCARD and CFG_STEPPER can not be defined at the same time since they both use pin 3.0."
1362   #endif
1363 #endif
1364
1365 #ifdef CFG_ST7565
1366   #ifdef CFG_SSD1306
1367     #error "CFG_ST7565 and CFG_SSD1306 can not be defined at the same time"
1368   #endif
1369 #endif
1370
1371 #ifdef CFG_RSA
1372   #if CFG_RSA_BITS != 64 && CFG_RSA_BITS != 32
1373     #error "CFG_RSA_BITS must be equal to either 32 or 64."
1374   #endif
1375 #endif
1376
1377 #if ADC_AVERAGING_ENABLE && ADC_AVERAGING_SAMPLES < 1
1378   #error "ADC_AVERAGING_SAMPLES must be 1 or higher when ADC averaging is enabled"
1379 #endif
1380
1381 #endif